Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM2170E _59 Vehicle Exterior _057048 WIPER / WASHER _0278174 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85143R 1.INSTALL REAR WIPER MOTOR GROMMET

a.
E237516E02
1.417,0.396 1.729,0.792 1.729,0.792 2.021,0.396 false 1.656,0.802 1.833,0.948 0.177,0.146 10 false *a

Apply MP grease to the entire surface of the rear wiper motor grommet lip.

Text in Illustration
*a Rear Wiper Motor Grommet Lip

HINT:

Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



b.

Install the rear wiper motor grommet.


Hide 85110R 2.INSTALL REAR WIPER MOTOR ASSEMBLY

a.

Insert the shaft of rear wiper motor assembly to the rear wiper motor grommet.


b.
E237514

Install the rear wiper motor assembly with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


Hide 3.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.

When reusing the rear wiper arm and blade assembly:

i.
E237517E01
0.326,0.919 0.495,1.075 0.170,0.156 10 *1 0.52,1.005 1.6,1.01 false 2.674,2.794 2.839,2.931 0.165,0.137 10 *2 1.606,2.861 2.66,2.867 false

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Serrations
*2 Wiper Pivot Serrations



b.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Operate the wiper and stop the windshield wiper motor at the automatic stop position.


d.
E237512

Temporarily install the rear wiper arm and blade assembly.


e.
E237519E01
1.738,2.852 1.910,3.004 0.172,0.152 10 *1 0.606,2.373 0.720,2.537 0.115,0.163 10 A 0.606,2.683 0.720,2.846 0.115,0.163 10 A 1.394,2.627 1.738,2.852 false

Install the rear wiper arm and blade assembly with the nut to the position as shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

Text in Illustration
*1 Dot (print)

Area Measurement
A 10.0 mm (0.394 in.)

HINT:

Hold the wiper arm by hand while tightening the nut.



f.

Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not come into contact with the vehicle body.


g.

Lift the wiper arm twice after the wiper stops and check the wiper set position.


Hide 85292A 4.INSTALL REAR WIPER ARM HEAD CAP

a.
E237511

Engage the 2 guides to the rear wiper arm and blade assembly.


b.

Engage the 2 claws to install the rear wiper arm head cap as shown in the illustration.


Hide 67761A 5.INSTALL BACK DOOR TRIM COVER

Hide 67750 6.INSTALL BACK DOOR TRIM BOARD ASSEMBLY