Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.12–2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog lights via the FOG FR relay in the instrument panel junction block assembly.

WIRING DIAGRAM

E310183E02
6.219,0.479 6.625,0.656 0.406,0.177 10 false TRLY 6.219,1.875 6.625,2.052 0.406,0.177 10 false FFGO 0.229,0.469 1.094,0.802 0.865,0.333 10 false from Auxiliary Battery 3.354,3.354 4.979,3.688 1.625,0.333 10 false Instrument Panel Junction Block Assembly 5.979,0.385 6.156,0.563 0.177,0.177 10 false 14 5.979,1.781 6.156,1.958 0.177,0.177 10 false 13 3.229,0.5 3.448,0.656 0.219,0.156 10 false 3E 3.198,0.292 3.542,0.469 0.344,0.177 10 false 1*1 3.219,2.292 3.438,2.469 0.219,0.177 10 false 3C 3.26,2.073 3.365,2.25 0.104,0.177 10 false 7 1.865,0.635 2.333,0.813 0.469,0.177 10 false DC/DC 4.458,1.135 4.771,1.313 0.313,0.177 10 false TAIL 5.188,1.01 5.5,1.188 0.313,0.177 10 false TAIL 4.333,2.573 4.917,2.75 0.583,0.177 10 false FOG FR 5.083,2.448 5.656,2.625 0.573,0.177 10 false FOG FR 5.479,3.781 7.125,4.115 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 5.479,3.625 5.792,3.802 0.313,0.177 10 false MB 0.656,2.719 0.917,2.896 0.26,0.177 10 false A12 0.656,2.885 2.115,3.063 1.458,0.177 10 false Fog Light Assembly LH 0.667,4.052 2.01,4.229 1.344,0.177 10 false A63*3, A11*4 0.677,4.229 2.156,4.406 1.479,0.177 10 false Fog Light Assembly RH 1.833,2.156 1.927,2.333 0.094,0.177 10 false 2 0.896,2.156 0.99,2.333 0.094,0.177 10 false 1 1.833,3.458 1.927,3.635 0.094,0.177 10 false 2 0.896,3.458 0.99,3.635 0.094,0.177 10 false 1 3.229,1.188 3.438,1.333 0.208,0.146 10 false 3F 3.208,0.948 3.542,1.125 0.333,0.177 10 false 1*2 3.063,5 3.906,5.188 0.844,0.188 10 false *2: for RHD 3.063,4.604 3.906,4.792 0.844,0.188 10 false *1: for LHD 4.302,4.604 5.698,4.792 1.396,0.188 10 false *3: for LED Headlight 4.302,5 5.958,5.188 1.656,0.188 10 false *4: for Halogen Headlight

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.




OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Front Fog Light Relay Front fog light relay ON/OFF Light control switch is in tail position

OK:

Front fog light relay operates. (Front fog lights come on.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (FOG LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (FOG LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the A12 fog light assembly LH connector.


b.

Disconnect the A63*1 or A11*2 fog light assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-2 - 3C-7 Always Below 1 Ω
A63-2*1 - 3C-7 Always Below 1 Ω
A11-2*2 - 3C-7 Always Below 1 Ω
3C-7 - Body ground Always 10 kΩ or higher


*1: for LED Headlight

*2: for Halogen Headlight




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.
E343934E03
1.25,0.292 1.583,0.51 0.333,0.219 1.604,1.708 1.938,1.927 0.333,0.219 1.635,3.49 1.969,3.708 0.333,0.219 1.823,0.292 2.156,0.51 0.333,0.219 1.135,4.219 1.385,3.969 false 1.677,4.198 1.49,3.979 false 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1.344,0.323 1.583,0.521 0.24,0.198 10 false 3E 1.688,1.74 1.927,1.938 0.24,0.198 10 false 3C 1.698,3.531 1.938,3.729 0.24,0.198 10 false MB 0.906,4.25 1.375,4.417 0.469,0.167 10 false FFGO 1.552,4.24 2.021,4.406 0.469,0.167 10 false TRLY 1.615,0.323 1.927,0.521 0.313,0.198 10 false *A 1.927,0.323 2.167,0.521 0.24,0.198 10 false 3F 2.188,0.323 2.5,0.521 0.313,0.198 10 false *B

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the auxiliary battery to terminal 3E-1*1 or 3F-1*2.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14 (TRLY) and MB-13 (FFGO).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-7 - Body ground Always 11 to 14 V


*1: for LHD

*2: for RHD


Text in Illustration
*A for LHD
*B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY