Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2011.12–2014.12
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light via the RR FOG relay in the instrument panel junction block assembly.

WIRING DIAGRAM

E241400E01
6.322,0.943 6.730,1.117 0.408,0.174 10 TRLY 6.322,2.449 6.896,2.637 0.574,0.189 10 RFGO 0.325,0.935 1.185,1.272 0.860,0.337 10 from Auxiliary Battery 3.454,3.817 5.079,4.149 1.625,0.332 10 Instrument Panel Junction Block Assembly 6.083,0.855 6.258,1.030 0.175,0.174 10 14 6.083,2.358 6.258,2.532 0.175,0.174 10 27 3.326,0.943 3.533,1.117 0.208,0.174 10 3E 3.362,0.757 3.456,0.932 0.095,0.174 10 1 3.318,2.855 3.541,3.030 0.223,0.174 10 3D 3.364,2.67 3.468,2.844 0.105,0.174 10 3 1.964,1.104 2.431,1.279 0.467,0.174 10 DC/DC 4.558,1.598 4.871,1.773 0.313,0.174 10 TAIL 5.29,1.481 5.603,1.655 0.313,0.174 10 TAIL 4.421,3.106 5.086,3.314 0.665,0.208 10 FOG RR 5.164,2.984 5.843,3.158 0.679,0.174 10 FOG RR 5.452,4.388 7.093,4.720 1.641,0.332 10 Main Body ECU (Multiplex Network Body ECU) 5.452,4.229 5.765,4.403 0.313,0.174 10 MB 0.5,3.324 0.765,3.499 0.265,0.174 10 M5 0.5,3.483 2.964,3.748 2.465,0.265 10 Rear Combination Light Assembly LH 1.928,2.771 2.023,2.946 0.095,0.174 10 6 0.996,2.778 1.090,2.952 0.095,0.174 10 1 1.196,3.077 1.836,3.254 0.641,0.177 10 Rear Fog 1.15,2.778 1.301,2.974 0.151,0.196 10 E 1.744,2.771 1.896,2.967 0.151,0.196 10 B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.




OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light relay ON/OFF Light control switch is in tail position

OK:

Rear fog light relay operates. (Rear fog light comes on.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

U183727E02
3.375,2.802 3.438,3.167 false 4.875,2.813 4.938,3.177 false 0.135,0.021 0.333,0.208 0.198,0.188 10 false *a 3.313,3.198 3.688,3.354 0.375,0.156 10 false TRLY 4.781,3.219 5.438,3.448 0.656,0.229 10 false RFGO 1.896,0.438 2.083,0.615 0.188,0.177 10 false 3E 4.76,0.354 4.958,0.531 0.198,0.177 10 false 3D 3.604,2.292 3.833,2.469 0.229,0.177 10 false MB

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


c.

Connect a positive (+) lead from the auxiliary battery to terminal 3E-1.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14 (TRLY) and MB-27 (RFGO).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3D-3 - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the M5 rear combination light assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-6 (B) - 3D-3 Always Below 1 Ω
3D-3 - Body ground Always 10 kΩ or higher
M5-1 (E) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR