Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E241402E02
1.438,1.75 2.417,1.958 0.979,0.208 10 false Parking Lights 0.26,2.49 2.385,2.823 2.125,0.333 10 false Taillights and License Plate Lights 3.281,1.76 3.5,1.938 0.219,0.177 10 false 3C 3.292,2.479 3.49,2.656 0.198,0.177 10 false 3D 3.281,2.271 3.469,2.448 0.188,0.177 10 false 10 3.313,1.563 3.438,1.771 0.125,0.208 10 false 2 0.396,0.51 1.26,0.844 0.865,0.333 10 false from Auxiliary Battery 1.969,0.719 2.438,0.896 0.469,0.177 10 false DC/DC 3.281,0.542 3.51,0.719 0.229,0.177 10 false 3E 3.323,0.333 3.417,0.51 0.094,0.177 10 false 1 4.521,1.219 4.833,1.396 0.313,0.177 10 false TAIL 5.26,1.083 5.573,1.26 0.313,0.177 10 false TAIL 6.302,0.552 6.719,0.729 0.417,0.177 10 false TRLY 6.052,0.406 6.229,0.583 0.177,0.177 10 false 14 5.458,3.542 7.104,3.875 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 5.448,3.354 5.677,3.531 0.229,0.177 10 false MB 3.271,2.938 5.917,3.104 2.646,0.167 10 false Instrument Panel Junction Block Assembly 3.302,1.083 3.531,1.26 0.229,0.177 10 false 3F 3.292,0.729 3.521,0.906 0.229,0.177 10 false *1 3.313,1.281 3.542,1.458 0.229,0.177 10 false *2 3.323,0.896 3.531,1.104 0.208,0.208 10 false 1 1.135,3.625 1.938,3.833 0.802,0.208 10 false *1: for LHD 1.146,3.969 1.948,4.177 0.802,0.208 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight relay ON/OFF -

OK:

Taillight relay operates. (Taillights illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
U183668E02
0.063,0.021 0.229,0.177 0.167,0.156 10 false *a 1.198,0.292 1.406,0.448 0.208,0.156 10 false 3E 1.917,0.281 2.125,0.438 0.208,0.156 10 false 3F 1.531,0.292 1.74,0.448 0.208,0.156 10 false *A 2.25,0.281 2.458,0.438 0.208,0.156 10 false *B

Disconnect the 3E*1 or 3F*2 instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3E-1*1 - Body ground Always 11 to 14 V
3F-1*2 - Body ground Always 11 to 14 V


*1: for LHD

*2: for RHD


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

U183679E01
0.147,0.129 0.303,0.284 0.156,0.155 10 *a 3.117,3.286 3.493,3.441 0.376,0.155 10 TRLY 3.301,2.88 3.301,3.269 false 3.489,2.208 3.761,2.364 0.272,0.156 10 MB 2.971,0.303 3.184,0.458 0.213,0.156 10 3C 0.533,0.415 0.732,0.570 0.200,0.156 10 3E 5.731,0.303 5.944,0.458 0.213,0.156 10 3D 1.163,0.409 1.363,0.565 0.200,0.156 10 3F 0.827,0.419 1.027,0.575 0.200,0.156 10 *A 1.457,0.405 1.657,0.561 0.200,0.156 10 *B

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


c.

Connect a positive (+) lead from the auxiliary battery to terminal 3E-1*1 or 3F-1*2.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14 (TRLY).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-2 - Auxiliary battery negative terminal Always 11 to 14 V
3D-10 - Auxiliary battery negative terminal Always 11 to 14 V


*1: for LHD

*2: for RHD




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY