Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2011.12–2014.12
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

These DTCs are stored when the low beam headlights do not illuminate, or a malfunction is detected in the communication between the headlight assembly and main body ECU (multiplex network body ECU).

DTC No. DTC Detection Condition Trouble Area
B2430 LED headlight LH circuit malfunction
·

Light control ECU LH

·

Headlight assembly LH

·

H-LP Relay

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


B2431 LED headlight RH circuit malfunction
·

Light control ECU RH

·

Headlight assembly RH

·

H-LP Relay

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E233295E14
5.469,6.49 7.094,6.948 1.625,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 3.146,2.729 3.292,2.906 0.146,0.177 10 false 1 3.146,3.208 3.281,3.385 0.135,0.177 10 false 3 2.854,2.729 3.073,2.906 0.219,0.177 10 false LO 0.531,2.979 0.677,3.156 0.146,0.177 10 false E 6.167,0.885 6.635,1.063 0.469,0.177 10 false HRLY 6.167,3.365 6.625,3.542 0.458,0.177 10 false LLEW 6.167,6.042 6.635,6.219 0.469,0.177 10 false RLEW 1.125,3.844 2.635,4.021 1.51,0.177 10 false Headlight Assembly LH 1.125,3.677 1.427,3.854 0.302,0.177 10 false A10 2.802,3.198 3.219,3.385 0.417,0.188 10 false LED 0.344,2.979 0.458,3.156 0.115,0.177 10 false 2 5.792,0.688 6.01,0.865 0.219,0.177 10 false 15 4.667,0.885 4.917,1.063 0.25,0.177 10 false 3C 5.75,3.354 6.094,3.531 0.344,0.177 10 false G60 5.75,6.042 6.104,6.219 0.354,0.177 10 false G60 5.76,0.875 6.031,1.052 0.271,0.177 10 false MB 4.667,0.698 4.896,0.875 0.229,0.177 10 false 18 5.813,3.146 6.021,3.323 0.208,0.177 10 false 24 5.802,5.833 5.99,6.01 0.188,0.177 10 false 21 3.49,1.417 3.854,1.594 0.365,0.177 10 false H-LP 2.052,1.292 2.833,1.469 0.781,0.177 10 false H-LP MAIN 1.49,2.219 2.229,2.438 0.74,0.219 10 false Low (LED) 0.177,1.094 1.542,1.469 1.365,0.375 10 false from Auxiliary Battery 3.292,3.01 4.094,3.188 0.802,0.177 10 false H-LP LH-LO 3.313,5.708 4.177,5.885 0.865,0.177 10 false H-LP RH-LO 4.448,1.25 6.104,1.74 1.656,0.49 10 false Instrument Panel Junction Block Assembly 1.177,2.865 2.469,3.24 1.292,0.375 10 false Light Control ECU (LED Driver Module) 1.177,5.531 2.469,5.906 1.292,0.375 10 false Light Control ECU (LED Driver Module) 3.146,5.417 3.292,5.594 0.146,0.177 10 false 1 3.146,5.917 3.281,6.094 0.135,0.177 10 false 3 2.854,5.417 3.073,5.594 0.219,0.177 10 false LO 0.531,5.656 0.677,5.833 0.146,0.177 10 false E 1.125,6.698 2.635,6.875 1.51,0.177 10 false Headlight Assembly RH 1.125,6.521 1.427,6.698 0.302,0.177 10 false A9 2.813,5.927 3.167,6.135 0.354,0.208 10 false LED 0.344,5.656 0.458,5.833 0.115,0.177 10 false 2 1.49,4.885 2.229,5.104 0.74,0.219 10 false Low (LED) 3.198,0.781 3.302,0.958 0.104,0.177 10 false 1 4.021,0.771 4.125,0.948 0.104,0.177 10 false 2 3.208,1.021 3.313,1.198 0.104,0.177 10 false 5 4.021,1.031 4.125,1.208 0.104,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Both DTC B2430 and B2431 are not output. A
Both DTC B2430 and B2431 are output. B
DTC B2430 or B2431 is output. C




A

B

2.INSPECT H-LP RELAY

C

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - H-LP RELAY)
2.INSPECT H-LP RELAY
a.
E209495

Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - H-LP RELAY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - H-LP RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connector Condition Specified Condition
Relay terminal 1 - Body ground Power switch off 11 to 14 V
Relay terminal 5 - Body ground Power switch off 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

Disconnect the A10 headlight assembly LH connector.


b.

Disconnect the A9 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - A10-1 (LO) Always Below 1 Ω
Relay terminal 3 - A9-1 (LO) Always Below 1 Ω
Relay terminal 3 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 2 - 3C-18 Always Below 1 Ω
Relay terminal 2 - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.
U159634E01
0.164,0.16 0.364,0.347 0.200,0.187 10 *a 1.62,0.824 1.826,0.981 0.206,0.157 10 3C 1.59,2.99 1.817,3.152 0.227,0.162 10 MB 1.367,3.762 1.757,3.913 0.390,0.151 10 HRLY 1.594,3.486 1.594,3.748 false

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - MB-15 (HRLY) Always Below 1 Ω
3C-18 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - H-LP RELAY)
a.

Disconnect the A10 headlight assembly connector or the A9 headlight assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side (B2430)
Tester Connection Condition Specified Condition
A10-1 (LO) - Body ground Power switch off, light control switch in head position 11 to 14 V

RH Side (B2431)
Tester Connection Condition Specified Condition
A9-1 (LO) - Body ground Power switch off, light control switch in head position 11 to 14 V




OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (B2430)
Tester Connection Condition Specified Condition
A10-2 (E) - Body ground Always Below 1 Ω

RH Side (B2431)
Tester Connection Condition Specified Condition
A9-2 (E) - Body ground Always Below 1 Ω




OK

9.CHECK HEADLIGHT ASSEMBLY (INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HEADLIGHT ASSEMBLY (INPUT VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side (B2430)
Tester Connection Condition Specified Condition
A10-3 (LED) - Body ground Power switch on (IG), light control switch in head position 9.5 to 14 V

RH Side (B2431)
Tester Connection Condition Specified Condition
A9-3 (LED) - Body ground Power switch on (IG), light control switch in head position 9.5 to 14 V




OK

10.CHECK LIGHT CONTROL ECU

NG

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT ASSEMBLY)
10.CHECK LIGHT CONTROL ECU
a.

Replace the headlight control ECU with a new or known good one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL).


b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 is not output.




OK

END (HEADLIGHT CONTROL ECU WAS DEFECTIVE)

NG

11.CHECK HEADLIGHT ASSEMBLY
11.CHECK HEADLIGHT ASSEMBLY
a.

Replace the headlight assembly with a new or known good one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL).


b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 is not output.




OK

END (HEADLIGHT ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT ASSEMBLY)
a.

Disconnect the G60 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the A10 headlight assembly connector or the A9 headlight assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (B2430)
Tester Connection Condition Specified Condition
G60-24 (LLEW) - A10-3 (LED) Always Below 1 Ω
G60-24 (LLEW) - Body ground Always 10 kΩ or higher

RH Side (B2431)
Tester Connection Condition Specified Condition
G60-21 (RLEW) - A9-3 (LED) Always Below 1 Ω
G60-21 (RLEW) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR