Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2011.12–2014.12
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Low Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the low beam headlights via the H-LP relay.

WIRING DIAGRAM

for Halogen Headlight


E220269E09
6.001,0.729 6.409,0.904 0.408,0.174 10 HRLY 0.134,0.722 0.998,1.052 0.865,0.330 10 from Auxiliary Battery 5.467,2.548 7.108,2.879 1.641,0.332 10 Main Body ECU (Multiplex Network Body ECU) 5.654,0.544 5.828,0.718 0.175,0.174 10 15 4.825,0.729 5.049,0.904 0.224,0.174 10 3C 0.828,2.335 0.923,2.509 0.095,0.174 10 1 0.999,2.335 1.146,2.509 0.147,0.174 10 E 2.316,2.335 2.546,2.509 0.230,0.174 10 LO 0.999,4.322 1.146,4.496 0.147,0.174 10 E 2.316,4.322 2.546,4.496 0.230,0.174 10 LO 1.624,2.637 1.898,2.812 0.274,0.174 10 Low 1.624,4.623 1.898,4.797 0.274,0.174 10 Low 2.595,2.335 2.689,2.509 0.095,0.174 10 2 3.178,0.635 3.272,0.810 0.095,0.174 10 1 3.978,0.635 4.073,0.810 0.095,0.174 10 2 3.178,0.873 3.272,1.048 0.095,0.174 10 5 3.978,0.873 4.073,1.048 0.095,0.174 10 3 4.841,0.544 5.015,0.718 0.174,0.174 10 18 5.628,0.729 5.854,0.904 0.226,0.174 10 MB 3.232,2.582 4.017,2.757 0.785,0.174 10 H-LP LH-LO 0.828,4.322 0.923,4.496 0.095,0.174 10 1 2.595,4.322 2.689,4.496 0.095,0.174 10 2 1.41,0.868 2.211,1.043 0.801,0.174 10 H-LP MAIN 3.46,1.242 3.793,1.416 0.334,0.174 10 H-LP 3.222,4.565 4.027,4.739 0.804,0.174 10 H-LP RH-LO 1.022,3.02 1.288,3.195 0.265,0.174 10 A4 1.022,3.179 2.486,3.354 1.464,0.174 10 Headlight Assembly LH 0.976,4.999 1.241,5.174 0.265,0.174 10 A3 0.976,5.158 2.463,5.333 1.487,0.174 10 Headlight Assembly RH 4.788,1.081 5.859,1.627 1.071,0.546 10 Instrument Panel Junction Block Assembly


for LED Headlight


E220268E31
0.156,0.635 1.01,1.073 0.854,0.438 10 false from Auxiliary Battery 1.427,0.917 2.167,1.094 0.74,0.177 10 false H-LP MAIN 1.281,2.396 2.531,2.885 1.25,0.49 10 false Light Control ECU (LED Driver Module) 1.552,4.365 2.313,4.615 0.76,0.25 10 false Low (LED) 1.25,5.01 2.51,5.5 1.26,0.49 10 false Light Control ECU (LED Driver Module) 3.292,0.885 3.5,1.042 0.208,0.156 10 false 5 2.771,2.344 3.083,2.604 0.313,0.26 10 false LO 3.063,2.344 3.271,2.563 0.208,0.219 10 false 1 0.583,2.344 0.781,2.604 0.198,0.26 10 false 2 0.781,2.354 1.104,2.646 0.323,0.292 10 false E 2.76,4.958 2.969,5.115 0.208,0.156 10 false LO 3.052,4.958 3.26,5.115 0.208,0.156 10 false 1 0.573,4.969 0.885,5.219 0.313,0.25 10 false 2 0.781,4.969 0.99,5.125 0.208,0.156 10 false E 1.073,3.469 1.365,3.625 0.292,0.156 10 false A10 1.073,3.625 2.865,4.094 1.792,0.469 10 false Headlight Assembly LH 1.042,6.094 1.333,6.25 0.292,0.156 10 false A9 1.052,6.26 2.802,6.552 1.75,0.292 10 false Headlight Assembly RH 3.594,1.25 3.958,1.406 0.365,0.156 10 false H-LP 3.375,2.615 4.146,2.771 0.771,0.156 10 false H-LP LH-LO 3.385,5.24 5.073,5.677 1.688,0.438 10 false H-LP RH-LO 3.292,0.656 3.5,0.813 0.208,0.156 10 false 1 4.094,0.896 4.302,1.052 0.208,0.156 10 false 3 4.094,0.646 4.302,0.802 0.208,0.156 10 false 2 4.813,0.552 5.021,0.708 0.208,0.156 10 false 18 4.813,0.75 5.01,0.917 0.198,0.167 10 false 3C 5.635,0.573 5.844,0.729 0.208,0.156 10 false 15 5.615,0.76 5.927,0.948 0.313,0.188 10 false MB 6,0.76 6.417,0.917 0.417,0.156 10 false HRLY 4.688,1.094 5.771,1.688 1.083,0.594 10 false Instrument Panel Junction Block Assembly 5.469,2.604 7.115,3.125 1.646,0.521 10 false Main Body ECU (Multiplex Network Body ECU) 1.552,1.74 2.26,2.021 0.708,0.281 10 false Low (LED)


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Headlight relay (Low beam headlights) ON/OFF -

OK:

Headlight relay operates. (Low beam headlights illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT H-LP RELAY
2.INSPECT H-LP RELAY
a.

Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
E223988E02
2.594,1.052 2.521,1.125 false 2.208,1.271 2.208,1.406 false 2.615,1.469 2.698,1.375 false 2.969,1 2.875,0.906 false 0.344,0.76 0.552,1.01 0.208,0.25 10 3 0.344,1.177 0.625,1.448 0.281,0.271 10 1 1.604,0.76 1.865,0.99 0.26,0.229 10 5 1.604,1.177 1.844,1.458 0.24,0.281 10 2 2.677,1.198 2.865,1.417 0.188,0.219 10 5 2.177,1.427 2.427,1.677 0.25,0.25 10 2 2.417,1.104 2.615,1.354 0.198,0.25 10 3 2.771,0.729 3,0.979 0.229,0.25 10 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (H-LP MAIN FUSE - H-LP RELAY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (H-LP MAIN FUSE - H-LP RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 1 - Body ground Always 11 to 14 V
Relay terminal 5 - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

for Halogen Headlight

i.

Disconnect the A4 headlight assembly LH connector.


ii.

Disconnect the A3 headlight assembly RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - A4-2 (LO) Always Below 1 Ω
Relay terminal 3 - A3-2 (LO) Always Below 1 Ω
Relay terminal 3 - Body ground Always 10 kΩ or higher




b.

for LED Headlight

i.

Disconnect the A10 headlight assembly LH connector.


ii.

Disconnect the A9 headlight assembly RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - A10-1 (LO) Always Below 1 Ω
Relay terminal 3 - A9-1 (LO) Always Below 1 Ω
Relay terminal 3 - Body ground Always 10 kΩ or higher





OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 2 - 3C-18 Always Below 1 Ω
Relay terminal 2 - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.
U159633E01
0.164,0.16 0.364,0.347 0.200,0.187 10 *a 1.62,0.824 1.826,0.981 0.206,0.157 10 3C 1.59,2.99 1.817,3.152 0.227,0.162 10 MB 1.367,3.762 1.757,3.913 0.390,0.151 10 HRLY 1.594,3.486 1.594,3.748 false

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - MB-15 (HRLY) Always Below 1 Ω
3C-18 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY