Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.12–2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Low Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the low beam headlights via the H-LP relay.

WIRING DIAGRAM

E308061E04
0.188,1.104 2.115,1.313 1.927,0.208 10 false from Auxiliary Battery 2.052,1.281 2.917,1.49 0.865,0.208 10 false H-LP-MAIN 3.5,1.406 3.979,1.625 0.479,0.219 10 false H-LP 4.469,1.26 6.073,1.625 1.604,0.365 10 false Instrument Panel Junction Block Assembly 5.333,2.76 7.01,3.167 1.677,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 1.094,2.667 2.76,2.979 1.667,0.313 10 false Light Control ECU LH 1.406,4.542 2.552,4.719 1.146,0.177 10 false Low Beam 1.115,5.167 2.771,5.5 1.656,0.333 10 false Light Control ECU RH 1.188,6.271 2.594,6.458 1.406,0.188 10 false Headlight Assembly RH 3.271,5.583 4.208,5.76 0.938,0.177 10 false H-LP RH-LO 3.292,3.073 4.188,3.26 0.896,0.188 10 false H-LP LH-LO 6.146,0.875 6.604,1.094 0.458,0.219 10 false HRLY 1.135,3.75 2.802,4.063 1.667,0.313 10 false Headlight Assembly LH 3.208,0.76 3.448,0.979 0.24,0.219 10 false 1 4.031,0.75 4.271,0.969 0.24,0.219 10 false 2 4.031,1.021 4.271,1.24 0.24,0.219 10 false 3 3.219,1.021 3.458,1.24 0.24,0.219 10 false 5 4.667,0.875 4.906,1.094 0.24,0.219 10 false 3C 4.656,0.677 4.896,0.896 0.24,0.219 10 false 18 5.906,0.771 6.146,0.99 0.24,0.219 10 false 15 5.344,2.604 5.583,2.823 0.24,0.219 10 false MB 1.198,6.115 1.448,6.281 0.25,0.167 10 false A68 0.344,5.333 0.594,5.5 0.25,0.167 10 false 2 0.542,5.333 0.792,5.5 0.25,0.167 10 false E 0.323,2.823 0.573,2.99 0.25,0.167 10 false 2 0.552,2.823 0.802,2.99 0.25,0.167 10 false E 3.146,2.813 3.396,2.979 0.25,0.167 10 false 4 2.865,2.813 3.156,2.979 0.292,0.167 10 false LO 1.135,3.594 1.448,3.771 0.313,0.177 10 false A69 2.875,5.313 3.188,5.49 0.313,0.177 10 false LO 3.146,5.313 3.396,5.479 0.25,0.167 10 false 4 1.448,2.01 2.594,2.188 1.146,0.177 10 false Low Beam

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Headlight relay (low beam headlights) ON/OFF -

OK:

Headlight relay operates. (Low beam headlights illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT H-LP RELAY
2.INSPECT H-LP RELAY
a.

Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
E223988E02
2.594,1.052 2.521,1.125 false 2.208,1.271 2.208,1.406 false 2.615,1.469 2.698,1.375 false 2.969,1 2.875,0.906 false 0.344,0.76 0.552,1.01 0.208,0.25 10 3 0.344,1.177 0.625,1.448 0.281,0.271 10 1 1.604,0.76 1.865,0.99 0.26,0.229 10 5 1.604,1.177 1.844,1.458 0.24,0.281 10 2 2.677,1.198 2.865,1.417 0.188,0.219 10 5 2.177,1.427 2.427,1.677 0.25,0.25 10 2 2.417,1.104 2.615,1.354 0.198,0.25 10 3 2.771,0.729 3,0.979 0.229,0.25 10 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (H-LP MAIN FUSE - H-LP RELAY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (H-LP MAIN FUSE - H-LP RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 1 - Body ground Always 11 to 14 V
Relay terminal 5 - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

Disconnect the A69 headlight assembly LH connector.


b.

Disconnect the A68 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - A69-4 (LO) Always Below 1 Ω
Relay terminal 3 - A68-4 (LO) Always Below 1 Ω
Relay terminal 3 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 2 - 3C-18 Always Below 1 Ω
Relay terminal 2 - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.
U159633E01
0.164,0.16 0.364,0.347 0.200,0.187 10 *a 1.62,0.824 1.826,0.981 0.206,0.157 10 3C 1.59,2.99 1.817,3.152 0.227,0.162 10 MB 1.367,3.762 1.757,3.913 0.390,0.151 10 HRLY 1.594,3.486 1.594,3.748 false

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - MB-15 (HRLY) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY