Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2015.11–2019.07
RM2170E _59 Vehicle Exterior _057056 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0278228 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  The Sound does not Stop when The Engine is Operated or when The Shift Lever is in P  


DESCRIPTION

The vehicle approaching speaker controller receives engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the lower shift lever assembly, and produces the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM

E342158E02
3.479,0.573 3.948,0.76 0.469,0.188 10 false OPSW 3.958,0.479 4.135,0.646 0.177,0.167 10 false 12 5.073,0.448 5.25,0.615 0.177,0.167 10 false 1 4.771,0.885 5.063,1.052 0.292,0.167 10 false E2 4.771,1.021 7.146,1.375 2.375,0.354 10 false Engine Oil Pressure Switch Assembly 3.052,0.573 3.521,0.76 0.469,0.188 10 false SFTP 1.417,0.604 1.708,0.792 0.292,0.188 10 false P2 0.385,1 0.677,1.167 0.292,0.167 10 false G25 0.385,1.167 2.198,1.396 1.813,0.229 10 false Lower Shift Lever Assembly 2.823,0.49 3,0.656 0.177,0.167 10 false 11 1.688,0.49 1.885,0.677 0.198,0.188 10 false 2 3.063,1.594 3.448,1.781 0.385,0.188 10 false GND 2.896,1.49 3.073,1.656 0.177,0.167 10 false 7 2.646,1.969 3.01,2.135 0.365,0.167 10 false G85 2.656,2.115 4.01,2.469 1.354,0.354 10 false Vehicle Approaching Speaker Controller 5.01,1.635 5.188,1.802 0.177,0.167 10 false 22 4.792,2.052 5.083,2.219 0.292,0.167 10 false G1 4.792,2.198 6.688,2.552 1.896,0.354 10 false Combination Meter Assembly 5.26,1.74 5.51,1.906 0.25,0.167 10 false S

PROCEDURE

1.READ VALUE USING GTS (Oil Pressure SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Oil Pressure SW Oil pressure switch / OFF or ON OFF: Engine started
ON: Engine not started
-

Result:
Result Proceed to
The GTS display changes according to engine operation A
The GTS display does not change according to engine operation B




A

2.READ VALUE USING GTS (Shift Position)

B

6.CHECK ENGINE OIL PRESSURE SWITCH ASSEMBLY (INPUT SIGNAL)
2.READ VALUE USING GTS (Shift Position)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift Position P position switch / Not Parking or Parking Not Parking or Parking -

Result:
Result Proceed to
The GTS display changes according to the selected shift state A
The GTS display does not change according to the selected shift state B




A

B

3.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (SHIFT)
3.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (SHIFT)
a.

Disconnect the G25 lower shift lever assembly connector.


b.
U159740E01
1.348,0.291 1.630,0.473 0.281,0.181 10 G25 0.094,0.085 0.264,0.260 0.170,0.174 10 *a 0.909,0.667 1.453,1.235 false 0.656,0.49 0.913,0.665 0.257,0.174 10 P2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G25-2 (P2) - Body ground Power switch on (IG) 8 V or higher
Power switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Lower Shift Lever Assembly)


OK

4.CHECK LOWER SHIFT LEVER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - LOWER SHIFT LEVER ASSEMBLY)
4.CHECK LOWER SHIFT LEVER ASSEMBLY
a.

Reconnect the G25 lower shift lever assembly connector.


b.
U159746E02
2.271,0.385 1.844,0.99 false 0.729,1.01 1.521,1.417 0.792,0.406 10 false G25 0.135,0.094 0.49,0.365 0.354,0.271 10 false *a 2.313,0.208 2.708,0.448 0.396,0.24 10 false P2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G25-2 (P2) - Body ground Power switch on (IG), park (P) selected 8 V or higher
Power switch on (IG), park (P) not selected Below 2.5 V



Text in Illustration
*a Component with harness connected
(Lower Shift Lever Assembly)


OK

NG

REPLACE LOWER SHIFT LEVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - LOWER SHIFT LEVER ASSEMBLY)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Disconnect the G25 lower shift lever assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-11 (SFTP) - G25-2 (P2) Always Below 1 Ω
G85-11 (SFTP) or G25-2 (P2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ENGINE OIL PRESSURE SWITCH ASSEMBLY (INPUT SIGNAL)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.
U183751E02
2.135,1.417 2.51,1.76 false 1.583,0.24 1.917,0.406 0.333,0.167 10 false G85 2.375,1.771 2.927,1.938 0.552,0.167 10 false OPSW 0.094,0.094 0.427,0.26 0.333,0.167 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G85-12 (OPSW) - Body ground Idling* 8 V or higher
Power switch on (IG) Below 2 V


HINT:

*:Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).



Text in Illustration
*a Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)


OK

NG

7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OILPRESSURE SWITCH ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OILPRESSURE SWITCH ASSEMBLY)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Disconnect the E2 engine oil pressure switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-12 (OPSW) - E2-1 Always Below 1 Ω
G85-12 (OPSW) or E2-1 - Body ground Always 10 kΩ or higher




OK

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR