Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2015.11–2018.08
RM2170E _59 Vehicle Exterior _057056 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0278228 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  Communication between Vehicle Proximity Notification System and Diagnostic Tool is not Possible  


DESCRIPTION

The vehicle approaching speaker controller communicates with the GTS through the DLC3.

WIRING DIAGRAM

E285125E08
6.01,0.51 6.219,0.698 0.208,0.188 10 false IG 6.01,2.646 6.396,2.833 0.385,0.188 10 false GND 5.833,2.521 6.01,2.688 0.177,0.167 10 false 7 5.594,2.833 5.958,3 0.365,0.167 10 false G85 5.594,3.021 7.01,3.375 1.417,0.354 10 false Vehicle Approaching Speaker Controller 5.833,0.417 6.01,0.583 0.177,0.167 10 false 1 6.01,1.042 6.427,1.229 0.417,0.188 10 false PRST 5.833,0.969 6.01,1.135 0.177,0.167 10 false 9 1.385,2.385 1.563,2.552 0.177,0.167 10 false 7 1.375,2.667 1.552,2.833 0.177,0.167 10 false 4 0.458,2.979 0.75,3.146 0.292,0.167 10 false G4 0.458,3.146 1.729,3.5 1.271,0.354 10 false DLC3 1.063,2.469 1.323,2.656 0.26,0.188 10 false SIL 1.073,2.76 1.333,2.948 0.26,0.188 10 false CG 0.594,0.521 1.594,0.875 1,0.354 10 false from IG1 NO. 1 Relay 1.875,0.635 2.417,0.823 0.542,0.188 10 false GAUGE 2.698,1.052 2.896,1.219 0.198,0.167 10 false 3C 2.688,0.521 2.885,0.688 0.198,0.167 10 false 3A 2.698,0.323 2.896,0.49 0.198,0.167 10 false 49 2.688,0.854 2.885,1.021 0.198,0.167 10 false 16 0.427,1.948 3.198,2.302 2.771,0.354 10 false Instrument Panel Junction Block Assembly 2.698,1.5 2.896,1.667 0.198,0.167 10 false 3A 2.708,1.323 2.906,1.49 0.198,0.167 10 false 32

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

The vehicle approaching speaker controller and GTS communicate using SIL communication.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Health Check.

Result:
Result Proceed to
Communication with the vehicle approaching speaker controller is not possible A
Communication with the vehicle approaching speaker controller is possible B




A

2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - IG1 NO. 1 RELAY)

B

2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - IG1 NO. 1 RELAY)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G85-1 (IG) - Body ground Power switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-7 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - DLC3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - DLC3)
a.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-9 (PRST) - G4-7 (SIL) Always Below 1 Ω
G85-9 (PRST) or G4-7 (SIL) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-4 (CG) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-1 (IG) - 3A-49 Always Below 1 Ω
G85-1 (IG) or 3A-49 - Body ground Always 10 kΩ or higher




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-9 (PRST) - 3C-16 Always Below 1 Ω
G85-9 (PRST) or 3C-16 - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DLC3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DLC3)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-32 - G4-7 (SIL) Always Below 1 Ω
3A-32 or G4-7 (SIL) - Body ground Always 10 kΩ or higher




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR