CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main body ECU (Multiplex network body ECU) with 1 connector | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | *2 | 1 connector |
| *A | Main Body ECU (Multiplex Network Body ECU) with 2 connectors | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | *2 | 2 connector |
Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3C-21 - Body ground | L - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| 3E-1 - Body ground*1, *2 | B - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| 3F-1 - Body ground*1, *3 | B - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| 3B-8 - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Connect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3A-28 - Body ground*1 | R - Body ground | Parking brake switch input | Parking brake switch on | Below 1 V |
| Parking brake switch off | 11 to 14 V | |||
| 3B-33 - Body ground*1, *8 | BE - Body ground | DRL relay drive output | Daytime running lights on | Below 1 V |
| Daytime running lights off | 11 to 14 V | |||
| 3C-2 - Body ground*1 | G - Body ground | Taillight relay drive signal output | Light control switch in tail or head position | 11 to 14 V |
| Light control switch off | Below 1 V | |||
| 3C-7 - Body ground*1, *4 | L - Body ground | Front fog light drive output | Light control switch in tail position, front fog light switch on | 11 to 14 V |
| Light control switch in tail position, front fog light switch off | Below 1 V | |||
| 3C-18 - Body ground*1 | V - Body ground | Headlight relay drive output | Light control switch in head position | Below 1 V |
| Light control switch not in head position | 11 to 14 V | |||
| 3C-35 - Body ground*1 | P - Body ground | High beam headlight drive output | Dimmer switch in high or high flash position | Below 1 V |
| Dimmer switch in low position | 11 to 14 V | |||
| 3D-3 - Body ground*1, *5 | G - Body ground | Rear fog light drive output | Light control switch in tail position, rear fog light switch on | 11 to 14 V |
| Light control switch in tail position, rear fog light switch off | Below 1 V | |||
| 3D-10 - Body ground*1 | G - Body ground | Taillight relay drive signal output | Light control switch in tail or head position | 11 to 14 V |
| Light control switch off | Below 1 V | |||
| G59-1 (RFOG) - Body ground*1, *5 | LG - Body ground | Rear fog light switch input | Rear fog light switch on | Below 1 V |
| Rear fog light switch off | Pulse generation | |||
| G59-5 (HU) - Body ground*1 | L - Body ground | Dimmer switch high position signal input | Dimmer switch in high position | Below 1 V |
| Dimmer switch not in high position | Pulse generation | |||
| G59-8 (HF) - Body ground*1 | L - Body ground | Dimmer switch high flash position signal input | Dimmer switch in high flash position | Below 1 V |
| Dimmer switch not in high flash position | Pulse generation | |||
| G59-20 (CLTB) - G59-22 (CLTE)*1, *7 | W - G | Automatic light control sensor power supply output | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| G59-21 (CLTS) - Body ground*1, *7 | B - Body ground | Automatic light control sensor signal input | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation
(See waveform 1) |
|||
| G59-27 (FFOG) - Body ground*1, *4 | GR - Body ground | Front fog light switch input | Front fog light switch on | Below 1 V |
| Front fog light switch off | Pulse generation | |||
| G59-28 (A) - Body ground*1, *7 | R - Body ground | Light control switch AUTO position signal input | Light control switch in AUTO position | Below 1 V |
| Light control switch not in AUTO position | Pulse generation | |||
| G59-29 (HEAD) - Body ground*1 | L - Body ground | Light control switch head position input | Light control switch in head position | Below 1 V |
| Light control switch not in head position, power switch off | Pulse generation | |||
| G59-30 (TAIL) - Body ground | SB - Body ground | Light control switch tail position signal input | Light control switch in tail or head position | Below 1 V |
| Light control switch not in tail or head position, power switch off | Pulse generation | |||
| G60-21 (RLEW) - Body ground*1, *6 | L - Body ground | Light control ECU RH signal input | Power switch on (IG), light control switch off | 11 to 14 V |
| Power switch on (IG), light control switch in head position | Pulse generation | |||
| G60-24 (LLEW) - Body ground*1, *6 | P - Body ground | Light control ECU LH signal input | Power switch on (IG), light control switch off | 11 to 14 V |
| Power switch on (IG), light control switch in head position | Pulse generation |
*1: w/ Light Auto Turn-off System
*2: for LHD
*3: for RHD
*4: w/ Front Fog Light
*5: w/ Rear Fog Light
*6: for LED Headlight
*7: w/ Automatic Light Control
*8: w/ Daytime Running Light
Waveform 1
| Item | Content |
|---|---|
| Tester Connection | G59-21 (CLTS) - Body ground |
| Tool setting | 5 V/DIV., 5 ms./DIV. |
| Condition | Power switch on (IG) |
The wavelength (A) of the waveform changes according to the surrounding brightness.
COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
HYBRID VEHICLE CONTROL ECU
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>TERMINALS OF ECU