Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057047 MIRROR (EXT) _0278167 POWER MIRROR CONTROL SYSTEM J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM  Mirror Heater does not Operate with Rear Defogger Switch  


DESCRIPTION

When the mirror heater switch (rear window defogger switch) on the air conditioning panel sub-assembly (heater control switch board) is pressed, the operation signal is sent to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the DEF relay to operate the mirror heaters.

WIRING DIAGRAM

B324605E06
0.625,7.323 2.802,7.677 2.177,0.354 10 false : LIN Communication Line 0.021,1.698 0.896,2.167 0.875,0.469 10 false from Auxiliary Battery 0.26,2.646 0.813,3.271 0.552,0.625 10 false from IG1 NO. 1 Relay 1.49,1.917 2.406,2.115 0.917,0.198 10 false DEF 1.125,2.792 2.042,2.99 0.917,0.198 10 false ECU-IG NO. 1 2.438,3.156 3.604,3.406 1.167,0.25 10 false DEF 3.25,1.885 4.167,2.083 0.917,0.198 10 false MIR HTR 5.031,1.063 6.198,1.313 1.167,0.25 10 false Outer Mirror RH 5.042,3.333 6.208,3.583 1.167,0.25 10 false Outer Mirror LH 4.385,1.448 5.552,1.698 1.167,0.25 10 false H7 4.375,1.604 6.854,1.948 2.479,0.344 10 false Outer Rear View Mirror Assembly RH 4.448,3.917 6.885,4.25 2.438,0.333 10 false Outer Rear View Mirror Assembly LH 4.49,3.75 5.656,4 1.167,0.25 10 false J7 0.781,6.448 1.948,6.698 1.167,0.25 10 false G33 0.781,6.615 3.198,7.073 2.417,0.458 10 false Air Conditioning Panel Sub-assembly (Heater Control Switch Board) 4,6.5 5.167,6.75 1.167,0.25 10 false G34 4,6.667 6.667,7.083 2.667,0.417 10 false Air Conditioning Amplifier Assembly 2,1.615 2.333,1.865 0.333,0.25 10 false 5 2,2.5 2.333,2.75 0.333,0.25 10 false 1 3.031,1.615 3.365,1.865 0.333,0.25 10 false 3 5.01,0.667 5.344,0.917 0.333,0.25 10 false 1 3.042,2.5 3.375,2.75 0.333,0.25 10 false 2 5.917,0.656 6.25,0.906 0.333,0.25 10 false 2 6.365,0.667 6.698,0.917 0.333,0.25 10 false - 4.594,0.667 4.927,0.917 0.333,0.25 10 false + 4.365,0.667 4.698,0.917 0.333,0.25 10 false 3 6.604,0.667 6.938,0.917 0.333,0.25 10 false 9 4.365,2.917 4.698,3.167 0.333,0.25 10 false 3 6.615,2.917 6.948,3.167 0.333,0.25 10 false 9 4.594,2.917 4.927,3.167 0.333,0.25 10 false + 5,2.917 5.333,3.167 0.333,0.25 10 false 1 5.927,2.917 6.26,3.167 0.333,0.25 10 false 2 6.365,2.917 6.698,3.167 0.333,0.25 10 false - 4.188,5.219 4.521,5.469 0.333,0.25 10 false 38 4.49,5.323 5.094,5.531 0.604,0.208 10 false RDFG 4.5,6.083 4.833,6.333 0.333,0.25 10 false LIN1 2.042,6.083 2.375,6.333 0.333,0.25 10 false LIN1 5.333,6.083 5.667,6.333 0.333,0.25 10 false GND 5.698,5.979 6.031,6.229 0.333,0.25 10 false 14 4.177,5.917 4.51,6.167 0.333,0.25 10 false 37 2.438,5.885 2.771,6.135 0.333,0.25 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the auxiliary battery voltage becomes low, mirror heater operation is canceled to prioritize supplying power to the power steering system.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner> Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Defogger Relay (Rear) Mirror Heater OFF or ON -

Body Electrical > Air Conditioner> Active Test
Tester Display
Defogger Relay (Rear)


Result:
Result Proceed to
Mirror heater operation on both mirrors is not normal A
Mirror heater operation on RH side mirror is not normal B
Mirror heater operation on LH side mirror is not normal C



A

2.CHECK WINDOW DEFOGGER SYSTEM

B

4.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH - BODY GROUND)

C

6.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH - BODY GROUND)
2.CHECK WINDOW DEFOGGER SYSTEM
a.

Check the window defogger system operation.

OK:

The window defogger system operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH/LH - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH/LH - BODY GROUND)
a.

Remove the DEF relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the H7 outer rear view mirror assembly RH connector.


c.

Disconnect the J7 outer rear view mirror assembly LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEF relay holder terminal-3 - J7-3 (+) Always Below 1 Ω
DEF relay holder terminal-3 - H7-3 (+) Always Below 1 Ω
DEF relay holder terminal-3 - Body Ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH - BODY GROUND)
a.

Remove the DEF relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the H7 outer rear view mirror assembly RH connector.


c.

Disconnect the J7 outer rear view mirror assembly LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEF relay holder terminal-3 - H7-3 (+) Always Below 1 Ω
H7-9 (-) - Body Ground Always Below 1 Ω
H7-3 (+) - Body Ground Always 10 kΩ or higher
DEF relay holder terminal-3 - Body Ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER MIRROR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT OUTER MIRROR RH

b.

Inspect the outer mirror RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION

OK:

Outer mirror RH is normal.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

6.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH - BODY GROUND)
a.

Remove the DEF relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the J7 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 outer rear view mirror assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEF relay holder terminal-3 - J7-3 (+) Always Below 1 Ω
J7-9 (-) - Body Ground Always Below 1 Ω
J7-3 (+) - Body Ground Always 10 kΩ or higher
DEF relay holder terminal-3 - Body Ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT OUTER MIRROR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT OUTER MIRROR LH

b.

Inspect the outer mirror LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION

OK:

Outer mirror LH is normal.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG