Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278073 WIRELESS DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B479736C01
1.625,3.833 2.042,4.104 0.417,0.271 4.458,3.813 4.792,4.073 0.333,0.26 5.063,3.813 5.396,4.073 0.333,0.26 1.698,5.198 2.031,5.458 0.333,0.26 4.958,5.188 5.292,5.448 0.333,0.26 1.698,6.552 2.031,6.813 0.333,0.26 4.958,6.542 5.292,6.802 0.333,0.26 3.281,7.833 3.615,8.094 0.333,0.26 1.667,1.469 1.917,1.469 false 0.635,2.667 1.031,2.667 false 3.792,1.031 3.792,0.531 3.792,0.531 3.958,0.531 false 1.604,0.854 1.604,0.521 1.604,0.521 1.771,0.521 false 0.125,0.177 0.5,0.417 0.375,0.24 12 false *A 1.823,0.438 2.135,0.635 0.313,0.198 10 false *1 4,0.438 4.313,0.635 0.313,0.198 10 false MB 1.958,1.385 2.417,1.583 0.458,0.198 10 false G59 0.896,1.448 1.208,1.646 0.313,0.198 10 false 3D 0.906,2.031 1.219,2.229 0.313,0.198 10 false 3C 0.25,2.573 0.865,2.771 0.615,0.198 10 false 3E*B 0.26,2.75 0.875,2.948 0.615,0.198 10 false 3F*C 5.844,1.385 6.156,1.583 0.313,0.198 10 false 3B 5.844,2.031 6.156,2.229 0.313,0.198 10 false 3A 1.708,3.875 2.167,4.073 0.458,0.198 10 false G59 4.542,3.854 4.854,4.052 0.313,0.198 10 false 3E 4.854,3.854 5.167,4.052 0.313,0.198 10 false *B 5.146,3.854 5.458,4.052 0.313,0.198 10 false 3F 5.469,3.854 5.781,4.052 0.313,0.198 10 false *C 1.781,5.229 2.094,5.427 0.313,0.198 10 false 3D 5.042,5.219 5.354,5.417 0.313,0.198 10 false 3C 1.771,6.583 2.083,6.781 0.313,0.198 10 false 3B 5.042,6.573 5.354,6.771 0.313,0.198 10 false 3A 3.344,7.875 3.656,8.073 0.313,0.198 10 false MB
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


B479735C01
3.323,7.51 3.677,7.792 0.354,0.281 4.729,6.292 5.083,6.573 0.354,0.281 1.74,6.292 2.094,6.573 0.354,0.281 1.052,5.042 1.406,5.323 0.354,0.281 3.854,5.052 4.208,5.333 0.354,0.281 5.427,5 5.781,5.281 0.354,0.281 6.083,5 6.438,5.281 0.354,0.281 4.573,3.708 4.99,4.021 0.417,0.313 2.167,3.708 2.583,4.021 0.417,0.313 0.656,2.75 1.031,2.75 false 1.615,0.958 1.615,0.573 1.615,0.573 1.781,0.573 false 4,1.135 4,0.667 4,0.667 4.167,0.667 false 1.667,1.583 2,1.583 false 1.667,2.031 2,2.031 false 3.396,7.563 3.708,7.76 0.313,0.198 10 false MB 4.823,6.333 5.135,6.531 0.313,0.198 10 false 3A 1.823,6.344 2.135,6.542 0.313,0.198 10 false 3B 1.146,5.094 1.458,5.292 0.313,0.198 10 false 3D 3.948,5.104 4.26,5.302 0.313,0.198 10 false 3C 5.521,5.063 5.833,5.26 0.313,0.198 10 false 3E 5.833,5.083 6.146,5.281 0.313,0.198 10 false *B 6.177,5.052 6.49,5.25 0.313,0.198 10 false 3F 6.479,5.104 6.792,5.302 0.313,0.198 10 false *C 4.656,3.781 5.115,3.979 0.458,0.198 10 false G59 2.25,3.781 2.708,3.979 0.458,0.198 10 false G60 0.271,2.667 0.667,2.917 0.396,0.25 10 false 3E*B 0.271,2.844 0.667,3.094 0.396,0.25 10 false 3F*C 1.813,0.5 2.125,0.698 0.313,0.198 10 false *1 0.917,1.531 1.229,1.729 0.313,0.198 10 false 3D 4.208,0.594 4.521,0.792 0.313,0.198 10 false MB 2.042,1.5 2.5,1.698 0.458,0.198 10 false G59 2.042,1.958 2.5,2.156 0.458,0.198 10 false G60 0.917,2.135 1.229,2.333 0.313,0.198 10 false 3C 5.854,1.49 6.167,1.688 0.313,0.198 10 false 3B 5.854,2.167 6.167,2.365 0.313,0.198 10 false 3A 0.125,0.094 0.5,0.333 0.375,0.24 12 false *A
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-32 (IG) - Body ground - IG power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - IG power supply Power switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3B-3 (ACT-) - Body ground R - Body ground Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3B-3 (ACT-) - Body ground R - Body ground Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-8 (ACT-) - Body ground P - Body ground Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-8 (ACT-) - Body ground P - Body ground Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-7 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-7 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3B-4 (ACT-) - Body ground*1 L - Body ground Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3B-4 (ACT-) - Body ground*1 L - Body ground Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3B-1 (ACT+) - Body ground Y - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3B-1 (ACT+) - Body ground Y - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3B-2 (ACT+) - Body ground V - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3B-2 (ACT+) - Body ground V - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3D-12 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-12 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3D-11 (ACT+) - Body ground GR - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-11 (ACT+) - Body ground GR - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3B-4 (ACTD) - Body ground*2 L - Body ground D door lock motor unlock drive output (driver door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3B-4 (ACTD) - Body ground*2 L - Body ground D door lock motor unlock drive output (driver door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
G59-19 (FRCY) - Body ground R - Body ground Front door courtesy light switch RH input Front door RH open Below 1 V
G59-19 (FRCY) - Body ground R - Body ground Front door courtesy light switch RH input Front door RH closed Pulse generation
3D-36 (FLCY) - Body ground R - Body ground Front door courtesy light switch LH input Front door LH open Below 1 V
3D-36 (FLCY) - Body ground R - Body ground Front door courtesy light switch LH input Front door LH closed Pulse generation
G59-24 (LCTY) - Body ground*1 L - Body ground Rear door courtesy light switch LH input Rear door LH open Below 1 V
G59-24 (LCTY) - Body ground*1 L - Body ground Rear door courtesy light switch LH input Rear door LH closed Pulse generation
G59-1 (LCTY) - Body ground*2 L - Body ground Rear door courtesy light switch LH input Rear door LH open Below 1 V
G59-1 (LCTY) - Body ground*2 L - Body ground Rear door courtesy light switch LH input Rear door LH closed Pulse generation
G59-6 (RCTY) - Body ground G - Body ground Rear door courtesy light switch RH input Rear door RH open Below 1 V
G59-6 (RCTY) - Body ground G - Body ground Rear door courtesy light switch RH input Rear door RH closed Pulse generation
G59-7 (LSFL) - Body ground L - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V
G59-7 (LSFL) - Body ground L - Body ground Front door LH unlock detection switch input Front door LH locked Pulse generation
G59-18 (LSFR) - Body ground L - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V
G59-18 (LSFR) - Body ground L - Body ground Front door RH unlock detection switch input Front door RH locked Pulse generation
3D-25 (LSR) - Body ground V - Body ground Rear door RH unlock detection switch input Rear door RH or LH unlocked Below 1 V
3D-25 (LSR) - Body ground V - Body ground Rear door RH unlock detection switch input Rear door RH and LH locked Pulse generation
3D-24 (LSR) - Body ground Y - Body ground Rear door LH unlock detection switch input Rear door LH or RH unlocked Below 1 V
3D-24 (LSR) - Body ground Y - Body ground Rear door LH unlock detection switch input Rear door LH and RH locked Pulse generation
3C-34 (BZR) - Body ground B - Body ground Wireless door lock buzzer signal Wireless door lock buzzer off Below 1 V
3C-34 (BZR) - Body ground B - Body ground Wireless door lock buzzer signal Wireless door lock buzzer on Pulse generation

*1: w/o Canister Pump Module

*2: w/ Canister Pump Module




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U183376E02
1.906,0.688 2.219,0.854 0.313,0.167 10 false G77 3.333,0.688 3.625,0.854 0.292,0.167 10 false G78 4.865,0.688 5.167,0.854 0.302,0.167 10 false G79

a.

Disconnect the G77 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G77-11 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
G77-2 (+B) - Body ground B - Body ground Auxiliary battery power supply Always 11 to 14 V
G77-10 (CUTB) - Body ground L - Body ground Dark current cut fuse pin input signal Always 11 to 14 V


c.

Reconnect the G77 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G79-5 (IG) - G77-11 (E) V - W-B IG power supply Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
G78-19 (RSSI) - G77-11 (E)*3 R - W-B*1
P - W-B*2
Communication channel switching circuit
Procedure:
1.

Power switch off

2.

All doors closed

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


11 to 14 V → Below 2 V
G78-6 (CSEL) - G77-11 (E)*4 R - W-B Communication channel switching circuit
Procedure:
1.

Turn power switch off

2.

Close all doors


No pulse generation → Pulse generation
G78-17 (RDAS) - G77-11 (E)*3
G78-17 (RDAM) - G77-11 (E)*4*5
LG - W-B Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 1)
G78-5 (RCO) - G77-11 (E) L - W-B Output to door control receiver (Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Below 1 V → 4.5 to 5.5 V

*1: for LHD

*2: for RHD

*3: for 5 Pin Type

*4: for 12 Pin Type and w/o Canister Pump Module

*5: for 12 Pin Type and w/ Canister Pump Module



e.
B251177C35
0.208,1 0.542,1.198 0.333,0.198 10 false GND 0.979,1.875 1.167,2.031 0.188,0.156 10 false *a 2.198,1.875 2.385,2.031 0.188,0.156 10 false *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1(Reference)
Item Content
Tester connection G78-17 (RDAS) - G77-11 (E)*1
G78-17 (RDAM) - G77-11 (E)*2
Tool setting 5 V/DIV., 500 ms/DIV.
Condition
Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed



*1: for 5 Pin Type

*2: for 12 Pin Type




CHECK DOOR CONTROL RECEIVER ASSEMBLY


U183413E02
3.448,0.302 3.771,0.458 0.323,0.156 10 false M15

a.

Disconnect the M15 door control receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M15-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the M15 door control receiver connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M15-2 (RSSI) - M15-1 (GND) Y - W-B Smart system receiving channel switching signal input All doors closed, all door lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → pressed 11 to 14 V → Below 2 V
M15-5 (DATA) - M15-1 (GND) L - W-B Smart system recovery code output All doors closed, all door lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → pressed Below 2 V → 11 to 14 V → Below 2 V
M15-4 (+5) - M15-1 (GND) V - W-B Receive mode switching signal input Power switch off and electrical key transmitter sub-assembly lock/unlock switch not pressed → pressed Below 1 V → 4.5 to 5.5 V



CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY


B443906E03
3.375,0.083 3.792,0.333 0.417,0.25 3.448,0.125 3.906,0.323 0.458,0.198 10 false M48

a.

Disconnect the M48 door control receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M48-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the M48 door control receiver connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M48-6 (CSEL) - M48-12 (GND)* Y - W-B Smart system receiving channel switching signal input The power switch off and close all doors No pulse generation → Pulse generation
M48-9 (DATA) - M48-12 (GND) L - W-B Smart system recovery code output All doors closed, all doors lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → pressed Below 1V → 10 to 16 V → Below 1V
M48-10 (+5) - M48-12 (GND) V - W-B Receive mode switching signal input Power switch off and electrical key transmitter sub-assembly lock/unlock switch not pressed → pressed Below 1 V → 4.5 to 5.5 V

*: w/o Canister Pump Module