Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stored the DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. DTC Detection Condition Trouble Area
P0420 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (1 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (sensor 1)

·

Heated oxygen sensor (sensor 2)

·

Exhaust manifold (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)

·

EGR valve assembly



CATALYST LOCATION

A269949E01
3.042,1.125 3.325,1.281 0.283,0.156 10 *7 1.454,1.354 1.743,0.872 1.743,0.872 1.972,0.872 false 2,0.82 2.239,0.976 0.239,0.156 10 *1 0.6,2.936 0.839,3.092 0.239,0.156 10 *6 5.748,0.942 5.889,1.126 5.889,1.126 6,1.126 false 6.036,1.055 6.275,1.211 0.239,0.156 10 *5 3.175,2.349 3.414,2.505 0.239,0.156 10 *4 1.814,3.098 1.957,3.519 1.957,3.519 2.16,3.519 false 1.051,2.546 1.290,2.702 0.239,0.156 10 *3 2.701,2.785 2.986,2.412 2.986,2.412 3.127,2.412 false 2.195,3.45 2.434,3.606 0.239,0.156 10 *2 1.354,2.485 1.289,2.602 1.289,2.602 1.209,2.602 false 1.034,2.726 0.925,2.999 0.925,2.999 0.789,2.999 false 2.632,1.549 2.828,1.185 2.828,1.185 3.007,1.185 false

Text in Illustration
*1 Air Fuel Ratio Sensor (Sensor 1) *2 Heated Oxygen Sensor (Sensor 2)
*3 TWC: Front Catalyst *4 TWC: Rear Catalyst
*5 Tail Exhaust Pipe Assembly *6 Exhaust Manifold
*7 Front Exhaust Pipe Assembly - -

NOTICE:

Replace the exhaust manifold (*6) and the front exhaust pipe assembly (*7) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *1 and heated oxygen sensor *2).


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related) Intake air temperature sensor
Mass air flow meter sub-assembly
Crank position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Response rate during fuel cut from rich condition Completed
Auxiliary battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 70%
All of the following conditions are met -
Mass air flow rate 1.5 gm/sec. or more, and less than 40 gm/sec.
Front catalyst temperature (estimated) 560°C (1040°F) or higher, and less than 770°C (1418°F)
Rear catalyst temperature (estimated) 450°C (842°F) or higher, and less than 700°C (1292°F)

TYPICAL MALFUNCTION THRESHOLDS

Oxygen Storage Capacity (OSC) of catalyst (Normalized) Less than 1

CONFIRMATION DRIVING PATTERN

HINT:
·

It is necessary for the response of the heated oxygen sensor to be normal in order to confirm DTC P0420. Therefore, perform the confirmation driving pattern for the heated oxygen sensor monitor before performing the confirmation driving pattern for the catalyst efficiency monitor.

·

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.



A337217E10
0.198,0.25 3.229,0.531 3.031,0.281 10 false Heated Oxygen Sensor monitor Driving Pattern 0.323,0.729 1.406,1.052 1.083,0.323 10 false Vehicle Speed 0.698,1.156 1.74,1.625 1.042,0.469 10 false 75 km/h 0.865,2.208 1.948,2.531 1.083,0.323 10 false Idling 0.156,2.479 1.604,2.76 1.448,0.281 10 false Power Switch off 1.573,2.698 2.51,3.094 0.938,0.396 10 false Warming up 2.646,2.729 3.958,3.063 1.313,0.333 10 false 10 minutes or more 1.833,2.125 2.125,2.427 0.292,0.302 10 false [A] 3.115,1.052 3.406,1.354 0.292,0.302 10 false [B]* 4.281,1.042 4.573,1.344 0.292,0.302 10 false [C] 5.26,1.052 5.552,1.354 0.292,0.302 10 false [C] 6.25,1.063 6.542,1.365 0.292,0.302 10 false [C] 6.948,2.229 7.146,2.531 0.198,0.302 10 false [D] 0.25,3.708 3.281,3.99 3.031,0.281 10 false Catalyst Efficiency Monitor Driving Pattern 0.854,6.031 1.938,6.354 1.083,0.323 10 false Idling 1.417,6.083 1.667,6.396 0.25,0.313 10 false [D] 0.146,6.292 1.594,6.573 1.448,0.281 10 false Power Switch off 1.708,6.969 2,7.271 0.292,0.302 10 false [E] 1.927,6.552 2.865,6.948 0.938,0.396 10 false Warming up 2.927,6.573 4.24,6.906 1.313,0.333 10 false 10 minutes or more 2.177,5.969 2.427,6.281 0.25,0.313 10 false [F] 3.385,4.875 3.677,5.177 0.292,0.302 10 false [G]* 4.344,6.99 4.635,7.292 0.292,0.302 10 false [H] 5.5,6.594 6.813,6.927 1.313,0.333 10 false 10 minutes or more 5.948,4.51 6.24,4.813 0.292,0.302 10 false [I]* 6.74,6.969 7.031,7.271 0.292,0.302 10 false [J] 0.115,7.5 4.823,7.75 4.708,0.25 10 false *: Drive the vehicle while keeping the engine load as constant as possible. 0.594,4.594 1.688,5.073 1.094,0.479 10 false 100 km/h 0.708,4.99 1.729,5.458 1.021,0.469 10 false 75 km/h

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) and turn the GTS on.

7.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P [A].

HINT:

In order to keep the idle stable, turn the A/C and all other electric loads off and do not perform any shift operations.


9.

Drive the vehicle at approximately 75 km/h (47 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

If the engine stops, further depress the accelerator pedal to restart the engine.



10.

With the shift lever in B, drive the vehicle at 75 km/h (47 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

Turn the power switch off and wait for at least 30 seconds [E].

12.

Turn the power switch on (IG) and turn the GTS on.

13.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [F].

14.

Drive the vehicle at approximately 75 km/h (47 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

The monitor item will change to Complete as the Catalyst Efficiency monitor operates.

·

If the engine stops, further depress the accelerator pedal to restart the engine.



15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P042000.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.



20.

Drive the vehicle at approximately 100 km/h (62 mph) for 10 minutes or more [I].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

If the engine stops, further depress the accelerator pedal to restart the engine.



21.

Enter the following menus: Powertrain / Engine / Trouble Codes [J].

22.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



23.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

24.

Input the DTC: P042000.

25.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A270243E45
4.906,3.104 4.906,3.323 false 4.906,3.323 5.26,3.323 false 5.198,3.104 5.198,3.323 false 1.75,2.844 1.615,3.104 false 3.625,0.854 3.854,1.052 0.229,0.198 10 false [E] 0.573,0.563 1.656,0.76 1.083,0.198 10 false Engine Speed 0.813,1.031 1.615,1.229 0.802,0.198 10 false 2500 rpm 0.813,1.573 1.615,1.771 0.802,0.198 10 false 1500 rpm 1.115,2.542 1.563,2.74 0.448,0.198 10 false Idling 0.396,2.76 1.573,2.958 1.177,0.198 10 false Power Switch off 1.292,3.125 1.938,3.323 0.646,0.198 10 false [A] to [C] 2.073,2.385 2.302,2.583 0.229,0.198 10 false [D] 4.792,0.854 5.021,1.052 0.229,0.198 10 false [F] 5.104,1.396 5.333,1.594 0.229,0.198 10 false [F] 2.094,3.115 3.01,3.313 0.917,0.198 10 false Warm up 3.365,3.115 4.542,3.313 1.177,0.198 10 false At least 3 minutes 5.292,3.24 6.104,3.438 0.813,0.198 10 false 2 seconds 4.865,3.354 5.333,3.573 0.469,0.219 10 false Check 6.635,2.771 7.031,2.969 0.396,0.198 10 false Time

Connect the GTS to the DLC3 [A].

(b) Turn the power switch on (IG) and turn the GTS on [B].

(c) Put the engine in inspection mode (maintenance mode) [C].

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

(d) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes [D].

(e) Run the engine at an engine speed of 2500 rpm for at least 3 minutes [E].

HINT:

During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform step [E] after charging control has completed.


(f) While running the engine at 2500 rpm for 2 seconds and 1500 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS [F].


HINT:
·

If either of the voltage outputs of the air fuel ratio or heated oxygen sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the GTS.

·

If the three-way catalytic converter has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).



A199479E09
0.255,0.104 4.136,0.267 3.882,0.163 10 Voltage output when active air fuel ratio control not performed: 2.433,0.532 3.565,0.695 1.132,0.163 10 Normal Catalyst 4.759,0.546 6.130,0.729 1.371,0.184 10 Deteriorated Catalyst 2.405,2.991 3.276,3.185 0.871,0.194 10 10 seconds 4.955,3.005 5.785,3.167 0.830,0.163 10 10 seconds 0.049,0.763 1.332,1.551 1.283,0.788 10 Waveform of Air Fuel Ratio Sensor in front of Three-way Catalytic Converter 1.465,0.784 1.810,0.926 0.345,0.142 10 3.4 V 1.465,1.204 1.810,1.346 0.345,0.142 10 3.1 V 1.459,2.053 1.810,2.256 0.351,0.204 10 1.0 V 1.536,2.724 1.811,2.950 0.275,0.225 10 0 V 0.038,2.164 1.374,2.952 1.336,0.788 10 Waveform of Heated Oxygen Sensor behind Three-way Catalytic Converter

CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0420 is output A
DTC P0420 and other DTCs are output B

HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up.


f.

Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

HINT:

During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.



g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.


h.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).


i.

Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result
Status
AFS Voltage B1S1
Status
O2S B1S2
Actual air fuel ratio, air fuel ratio sensor and
heated oxygen sensor condition
Misfire Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-way catalytic converter

·

Gas leak from exhaust system

·

EGR valve assembly


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean May occur
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system

·

EGR valve assembly


D
Rich Rich Actual air fuel ratio rich -
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system

·

EGR valve assembly



Lean: During Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.




A

3.CHECK FOR EXHAUST GAS LEAK

B

7.REPLACE AIR FUEL RATIO SENSOR

C

8.CHECK FOR EXHAUST GAS LEAK

D

10.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

14.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result
Result Proceed to
NG A
OK B



A

5.INSPECT EGR VALVE ASSEMBLY

B

6.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
5.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

6.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NG

6.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold (TWC: Front catalyst).

Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS


b.

Replace the front exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS



NEXT

END

7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

9.REPLACE HEATED OXYGEN SENSOR

NG

14.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
9.REPLACE HEATED OXYGEN SENSOR
a.

Replace the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
10.CHECK FOR EXHAUST GAS LEAK
a.

Check the exhaust gas leaks.

OK:

No gas leaks.




OK

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

14.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
11.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result
Result Proceed to
NG A
OK B



A

12.INSPECT EGR VALVE ASSEMBLY

B

13.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
12.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

13.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

13.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0171



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
14.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
a.

Repair or replace exhaust gas leak point.

HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


i.

Start the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


l.

Read the DTCs.

Result
Result Proceed to
DTC P0420 is output A
DTCs are not output
(No pending DTCs output)
B



A

16.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

B

END

16.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold (TWC: Front catalyst).

Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS


b.

Replace the front exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS



NEXT

END