Refer to DTC P0111.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0111
When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0112 | A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Short in intake air temperature sensor circuit ·
Intake air temperature sensor (built into mass air flow meter sub-assembly) ·
ECM |
| P0113 | An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open in intake air temperature sensor circuit ·
Intake air temperature sensor (built into mass air flow meter sub-assembly) ·
ECM |
When any of these DTCs are output, check the intake air temperature using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| Higher than 128°C (262°F) | Short circuit |
The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.
Example:
If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P0113. Conversely, if the output voltage is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0112.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the GTS on.
Wait 0.5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0112 or P0113.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.
Read the value displayed on the GTS.
Same as actual intake air temperature.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| Higher than 128°C (262°F) | B |
| Same as actual intake air temperature | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates higher than 128°C (262°F).
A
B
C
Disconnect the mass air flow meter sub-assembly connector.
| *1 | Mass Air Flow Meter Sub-assembly | *2 | ECM |
| *a | Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly) |
- | - |
Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly connector on the wire harness side.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.
Read the value displayed on the GTS.
Higher than 128°C (262°F)
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C21-1 (THA) - C10-90 (THA) | Always | Below 1 Ω |
| C21-2 (E2) - C10-122 (ETHA) | Always | Below 1 Ω |
OK
NG
Disconnect the mass air flow meter sub-assembly connector.
| *1 | Mass Air Flow Meter Sub-assembly |
| *2 | ECM |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.
Read the value displayed on the GTS.
-40°C (-40°F)
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C21-1 (THA) or C10-90 (THA) - Body ground | Always | 10 kΩ or higher |
OK
NG