Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P2610  ECM / PCM Internal Engine Off Timer Performance  


DTC SUMMARY

DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P2610 Soak timer (built into ECM) ECM internal malfunction (2 trip detection logic) ECM Power switch off 2 trip

DESCRIPTION

The soak timer operates after the power switch is turned off. When a certain amount of time has elapsed after turning the power switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A275902E03
4.679,0.585 5.078,0.741 0.399,0.156 10 IGSW 5.833,4.333 6.197,4.489 0.364,0.156 10 ECM 5.198,1.301 5.930,1.610 0.732,0.309 10 Soak Timer IC 5.226,2.617 5.887,2.945 0.661,0.328 10 Power Source IC 5.198,3.422 5.937,3.745 0.739,0.323 10 Main Relay Control IC 3.577,0.826 4.246,0.976 0.669,0.151 10 IG2 NO. 2 4.679,2.767 4.905,2.936 0.225,0.170 10 +B 4.679,3.572 5.113,3.728 0.434,0.156 10 MREL 2.602,1.392 2.851,1.548 0.248,0.156 10 IG2 1.34,0.826 1.626,0.988 0.286,0.163 10 IG2 0.629,4.211 1.340,4.532 0.711,0.321 10 Auxiliary Battery 2.432,3.963 3.084,4.119 0.652,0.156 10 EFI-MAIN 2.3,1.942 2.692,2.098 0.392,0.156 10 IG2D 2.243,2.262 3.816,2.658 1.573,0.395 10 Certification ECU (Smart Key ECU Assembly) 0.477,3.736 1.102,3.892 0.625,0.156 10 MAIN 1.351,3.404 2.036,3.560 0.685,0.156 10 EFI-MAIN 0.477,3.189 1.102,3.345 0.625,0.156 10 P/I

MONITOR DESCRIPTION

If the soak timer activates the ECM even though only a short amount of time has elapsed since the power switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the power switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the power switch is turned to on (IG).

MONITOR STRATEGY

Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) -
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Start the engine and warm it up.

8.

Turn the power switch off and wait for at least 15 seconds.

9.

Turn the power switch on (IG) and turn the GTS on.

10.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

11.

Start the engine and warm it up.

12.

Turn the power switch off and leave the vehicle for 60 minute or more.

13.

Turn the power switch on (IG) and turn the GTS on.

14.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

17.

Input the DTC: P2610.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


h.

If no pending DTC is output, the repair has been successfully completed.



NEXT

END