The ECM receives the fuel low level signal from the combination meter assembly (meter ECU) to detect if the vehicle is running out of fuel.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P3193 | All of the following conditions are met (1 trip detection logic):
·
Power switch on (IG). ·
The ECM receives the fuel low level signal from the combination meter assembly (meter ECU). ·
DTC detection conditions of either DTC P3190 or P3191 are met. |
- (This DTC indicates that the vehicle ran out of fuel and does not indicate the malfunction of a part.) |
This DTC indicates that the vehicle ran out of fuel. If the ECM receives the fuel low level signal from the combination meter assembly (meter ECU) and the DTC detection conditions of either DTC P3190 or P3191 are met while the power switch is on (IG) or the engine is operating, the ECM stores this DTC.
If the MIL or master warning light illuminates, stop the road test immediately. If DTC P3190, P3191 or P3193 is stored, engine operation may be disabled depending on the engine condition. In this case, the vehicle can be driven only a short distance as the HV battery will not be charged.
Apply the parking brake firmly.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (READY) and turn the GTS on.
Fully depress the accelerator pedal for 10 seconds with the vehicle stopped, the shift lever in P and the brake pedal depressed. [A]
As soon as the engine starts, release the accelerator pedal.
Drive the vehicle at an average of approximately 40 km/h (25 mph) or more until the total engine operation time is 10 minutes or more. [B]
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
It is not necessary to maintain the vehicle speed at 40 km/h (25 mph) throughout the road test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes. [C]
Read the DTCs (including pending DTCs).
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P3193.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, idle the engine for 10 seconds or more and check the DTC judgment result again.
If DTC P3190, P3191 or P3193 is stored, engine operation may be disabled depending on the engine condition. In this case, add fuel or perform a repair, then clear the DTCs and turn the power switch off to allow the operation to return to normal.
If DTC P3190, P3191 or P3193 is stored and engine operation is disabled, the HV battery will not be charged as the vehicle will operate using only the motor. If the vehicle is driven in this condition, the SOC will drop and the HV battery will be depleted, preventing the system from entering the READY-on state.
Check the amount of fuel remaining.
There is enough fuel.
DTCs P3190, P3191 and/or P3193 may be output if the vehicle ran out of fuel in the past.
If not enough fuel is added, DTC P3190, P3191 or P3193 may be output again. If the engine cannot be started because the vehicle is out of fuel, add fuel until the fuel level warning turns off.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Add fuel until the fuel level warning turns off.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (READY).
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P3190 or P3191 is output | B |
| DTC P3190 or P3191 and other DTCs are output | C |
A
B
C