Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P3190  Poor Engine Power  P3191  Engine does not Start  


DESCRIPTION

The ECM receives signals from the hybrid vehicle control ECU such as the requested engine torque, target engine speed and engine cranking status, and controls the engine output based on the target engine speed and requested torque.

DTC No. DTC Detection Condition Trouble Area
P3190 When all of the following conditions are met (1 trip detection logic):
·

Engine speed is 650 rpm or higher (varies depending on the engine coolant temperature).

·

Engine torque requested by the hybrid vehicle control ECU exceeds a certain level.

·

The hybrid vehicle control ECU judges that the engine has started.

·

The fuel tank is not empty.

·

Communication between the power management control ECU and ECM is normal

·

"The actual engine torque is less than 20% of the requested engine torque" for 6 seconds, or until the crankshaft turns 100 times (whichever takes longer, differs depending on the engine coolant temperature).


·

Intake system

·

Throttle body with motor assembly

·

Fuel system

·

Engine

·

Mass air flow meter sub-assembly

·

Out of fuel

·

Engine coolant temperature sensor

·

Crank position sensor

·

Cam position sensor

·

EGR valve assembly

·

PCV valve and hose

·

PCV hose connections

·

ECM


P3191 When all of the following conditions are met (1 trip detection logic):
·

Engine speed is 650 rpm or higher (varies depending on the engine coolant temperature).

·

The fuel tank is not empty.

·

Communication between the hybrid vehicle control ECU and ECM is normal.

·

After the hybrid vehicle control ECU sends the engine start request signal, it does not detect engine start (generation of engine torque) for 6 seconds, or until the crankshaft turns 100 times (whichever takes longer, differs depending on the engine coolant temperature).


·

Intake system

·

Throttle body with motor assembly

·

Fuel system

·

Engine

·

Mass air flow meter sub-assembly

·

Out of fuel

·

Engine coolant temperature sensor

·

Crank position sensor

·

Cam position sensor

·

EGR valve assembly

·

PCV valve and hose

·

PCV hose connections

·

ECM



MONITOR DESCRIPTION

1.

The ECM receives signals such as requested engine torque, target engine speed and engine cranking status from the hybrid vehicle control ECU.

2.

The ECM controls engine start and stop and the throttle valve angle based on the signals received from the hybrid vehicle control ECU.

3.

The ECM receives the actual engine torque calculated by the hybrid vehicle control ECU based on the generator torque.

4.

When the actual engine torque is less than 20% of the requested engine torque*1, the ECM judges that the engine output is abnormal and stores DTC P3190.

(The engine may not have started in the above situation.)

*1: Requested torque = Requested Engine Torque (kW) / HV Target Engine Speed (rpm) x 9549

5.

If the ECM does not detect engine start torque (actual engine torque) even though it has received an engine start request and started the engine, it stores DTC P3191.

HINT:
·

If DTC P3190, P3191 or P3193 is stored, engine operation may be disabled depending on the engine condition. In this case, add fuel or perform a repair, then clear the DTCs and turn the power switch off to allow the operation to return to normal.

·

If DTC P3190, P3191 or P3193 is stored and engine operation is disabled, the HV battery will not be charged as the vehicle will operate using only the motor. If the vehicle is driven in this condition, the SOC will drop and the HV battery will be depleted, preventing the system from entering the READY-on state.

·

When DTC P3190 or P3191 is stored, the engine torque has dropped by 80% or the engine cannot be started. If any DTCs that indicate malfunctioning of engine related parts are stored at the same time, repair the malfunctioning parts first.




Relevant Data List Items
ECM (Powertrain / Engine and ECT / Data List)
HV Target Engine Speed Engine Speed Requested Engine Torque Actual Engine Torque
Throttle Position Command Throttle Position No. 1 Calculate Load Coolant Temp
Short FT B1S1 Long FT B1S1 EGR Step Position -

HYBRID VEHICLE CONTROL ECU (Powertrain / Hybrid Control / Data List)
Target Engine Rev Engine Revolution Requested Engine Torque Engine Coolant Temp
Engine Idling Request - - -

MONITOR STRATEGY

Frequency of operation Continuous

CONFIRMATION DRIVING PATTERN

NOTICE:

If the MIL or master warning light illuminates, stop the road test immediately. If DTC P3190, P3191 or P3193 is stored and engine operation is disabled, the vehicle can be driven only a short distance as the HV battery will not be charged.


A299140E30
1.208,0.938 1.833,1.177 0.625,0.24 10 false 40 km/h 1.01,2.198 1.885,2.51 0.875,0.313 10 false READY ON 2.229,2.073 2.854,2.313 0.625,0.24 10 false [A] 3.417,0.552 4.042,0.792 0.625,0.24 10 false [B] 5.104,3.167 5.729,3.406 0.625,0.24 10 false [C] 3.021,2.802 4.823,3.177 1.802,0.375 10 false Total engine operation time of 10 min. or more

1.

Apply the parking brake firmly.

2.

Connect the GTS to the DLC3.

3.

Turn the power switch on (IG) and turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (READY) and turn the GTS on.

7.

Fully depress the accelerator pedal for 10 seconds with the vehicle stopped, the shift lever in P and the brake pedal depressed. [A]

NOTICE:

As soon as the engine starts, release the accelerator pedal.


8.

Drive the vehicle at an average of approximately 40 km/h (25 mph) or more until the total engine operation time is 10 minutes or more. [B]

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

It is not necessary to maintain the vehicle speed at 40 km/h (25 mph) throughout the road test.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes. [C]

10.

Read the DTCs (including pending DTCs).

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P3190 or P3191.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 10 seconds or more and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

Repeating this inspection for symptom confirmation may cause the SOC to drop, preventing the system from entering the READY-on state. In this case, use the THS charger to charge the HV battery.

·

Cranking the engine once causes the SOC to drop approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.

·

Charging the HV battery using the THS charger takes approximately 10 minutes when the HV battery temperature is 25°C or approximately 30 minutes when the HV battery temperature is 0°C.

·

The THS charger is a supplemental charging device that charges the HV battery enough to enable the engine to start (the vehicle can enter the READY-on state).

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P3190, P3191 AND/OR P3193)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P3190 or P3191 is output A
DTC P3193 is output B
DTC P3190, P3191 and/or P3193 and other DTCs are output C

HINT:

If any DTCs other than P3190, P3191 and/or P3193 are output, perform troubleshooting for those DTCs first.




A

2.CHECK SHORTAGE OF FUEL

B

C

2.CHECK SHORTAGE OF FUEL
a.

Check the amount of fuel remaining.

OK:

There is enough fuel.



HINT:
·

DTCs P3190, P3191 and/or P3193 may be output if the vehicle ran out of fuel in the past.

·

If not enough fuel is added, DTC P3190, P3191 or P3193 may be output again. If the engine cannot be started because the vehicle is out of fuel, add fuel until the fuel level warning turns off.




OK

3.CLEAR DTC

NG

REFILL FUEL

3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the power switch off and wait for at least 30 seconds.



NEXT

4.CHECK PCV HOSE CONNECTIONS
4.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>PCV VALVE>COMPONENTS

OK:

PCV valve and hose are connected correctly and are not damaged.




OK

5.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

5.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

6.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP
OK:

Unusual noise and vibration do not occur.



OK

7.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE MALFUNCTIONING PART

7.CHECK FUEL PRESSURE

OK

8.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY

NG

8.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Inspect the throttle body with motor assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>THROTTLE BODY>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

9.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

9.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

11.INSPECT CRANK POSITION SENSOR

NG

11.INSPECT CRANK POSITION SENSOR

OK

12.INSPECT CAM POSITION SENSOR

NG

12.INSPECT CAM POSITION SENSOR

OK

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.

·

If the Active Test cannot be performed due to a malfunction such as the engine not starting, perform the EGR value assembly inspection in the following step.



Result:
Result Proceed to
Outside standard range A
Within standard range B




A

14.INSPECT EGR VALVE ASSEMBLY

B

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190 OR P3191)
14.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190 OR P3191)

NG

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190 OR P3191)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG) and turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


i.

Read the pending DTCs.

Result
Result Proceed to
DTC P3190 or P3191 is output A
DTCs are not output B



A

16.REPLACE ECM

B

16.REPLACE ECM

NEXT

17.CONFIRM WHETHER DTC MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER DTC MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTC.


e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG) and turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P3190 or P3191.


j.

Check the DTC judgment result.



NEXT

END