Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P014C  A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1  P014D  A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1  P015A  A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1  P015B  A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1  


DESCRIPTION

Refer to DTC P2195.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P2195

DTC No. DTC Detection Condition Trouble Area
P014C The "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


P014D The "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
P015A The "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
P015B The "Lean to Rich delay level*" value is standard or more (2 trip detection logic).

*: Calculated by ECM based on the air fuel ratio sensor output.

MONITOR DESCRIPTION

After the engine has been warmed up, the ECM carries out air fuel ratio feedback control, and maintains the air fuel ratio at the theoretical level. In addition, after all the preconditions have been met, active air fuel ratio control is carried out for approximately 10 seconds and during active air fuel ratio control, the ECM measures the response of the air fuel ratio sensor by increasing or decreasing a specific injection quantity based on the theoretical air fuel ratio learned during normal air fuel control. The ECM determines whether there is an air fuel ratio sensor malfunction at the mid-point of active air fuel ratio control.

If the air fuel ratio sensor's response ability is reduced, DTC P014C and P014D are output.

If the air fuel ratio sensor output timing is delayed, DTC P015A and P015B are output.

A223538E28
0.133,0.032 2.413,0.216 2.281,0.184 10 Air Fuel Ratio Sensor Output: 0.289,0.978 1.722,1.365 1.434,0.387 10 Active Air Fuel Ratio Control 0.289,1.938 2.128,2.278 1.839,0.339 10 Air Fuel Ratio Sensor Output (Response Rate) 3.558,1.317 4.061,1.501 0.503,0.184 10 Normal 5.464,1.278 6.226,1.462 0.761,0.184 10 Malfunction 4.438,0.456 5.247,0.640 0.809,0.184 10 10 seconds 0.289,4.245 1.699,4.429 1.411,0.184 10 Fuel Injection Volume 2.774,3.966 3.416,4.150 0.642,0.184 10 Increase 2.774,4.438 3.416,4.621 0.642,0.184 10 Decrease 1.835,0.766 2.232,0.913 0.397,0.147 10 On 1.835,1.075 2.206,1.258 0.371,0.184 10 Off 4.206,1.689 4.049,1.387 false 5.228,1.921 5.445,1.357 false 0.289,3.13 2.142,3.484 1.853,0.354 10 Air Fuel Ratio Sensor Output (Delay Time) 3.58,2.684 4.083,2.868 0.503,0.184 10 Normal 4.795,2.54 5.556,2.724 0.761,0.184 10 Malfunction 4.189,2.993 4.07,2.754 false 4.511,2.979 4.762,2.606 false

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Vehicle speed sensor
Crank position sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Active air fuel ratio control Performing
Active air fuel ratio control is performed when the following conditions met -
Auxiliary battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idle Off
Engine speed 1000 rpm or higher, and less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel-cut Off
Engine load 10% or higher, and less than 70%
Catalyst monitor Not yet
Mass air flow 5 gm/sec. or more, and less than 15 gm/sec.

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation pattern will activate the air fuel ratio sensor response monitor.


A379317E04
2.344,2.198 2.802,2.448 0.458,0.25 10 false [A] 3.813,0.792 4.271,1.042 0.458,0.25 10 false [B] 4.646,3.01 5.104,3.26 0.458,0.25 10 false [C] 5.583,2.708 6.042,2.958 0.458,0.25 10 false Time 3.604,2.948 4.635,3.24 1.031,0.292 10 false 10 minutes 2.083,2.948 3.177,3.25 1.094,0.302 10 false Warming up 0.531,2.521 2.094,2.896 1.563,0.375 10 false Power Switch off 1.229,2.281 1.688,2.531 0.458,0.25 10 false Idling 0.042,0.927 1.667,1.292 1.625,0.365 10 true Between 75 and 100 km/h 0.74,0.448 1.938,0.771 1.198,0.323 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) and turn the GTS on.

7.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

8.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) [A].

9.

With the engine running, drive the vehicle at a constant speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P014C, P014D, P015A or P015B.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE or N/A, drive the vehicle again under an increased load and then recheck the judgment result.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P014C, P014D, P015A or P015B is output A
DTC P014C, P014D, P015A or P015B and other DTCs are output B

HINT:

If any DTCs other than P014C, P014D, P015A or P015B are output, troubleshoot those DTCs first.




A

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

B

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

OK

4.CHECK AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR FUEL RATIO SENSOR
a.

Check that the proper air fuel ratio sensors are installed to the vehicle.

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

5.PERFORM CONFIRMATION DRIVING PATTERN

NG

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to the Confirmation Driving Pattern.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


e.

Read the pending DTCs.

Result
Result Proceed to
DTC P014C, P014D, P015A or P015B are output A
DTCs are not output B



A

7.REPLACE AIR FUEL RATIO SENSOR

B

7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to the Confirmation Driving Pattern.



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


e.

Read the pending DTCs.

Result
Result Proceed to
DTCs are not output A
DTC P014C, P014D, P015A or P015B are output B



A

END

B

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO