Refer to DTC P2195.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P2195
When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the power switch is turned off.
Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0031 | Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater output duty cycle is 30% or higher (1 trip detection logic). | ·
Open in air fuel ratio sensor (sensor 1) heater circuit ·
Air fuel ratio sensor (sensor 1) ·
No. 1 integration relay ·
ECM |
| P0032 | Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic). | ·
Short in air fuel ratio sensor (sensor 1) heater circuit ·
Air fuel ratio sensor (sensor 1) ·
No. 1 integration relay ·
ECM |
| P101D | The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). | ECM |
The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.
The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.
When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
| Required Sensors/Components (Main) | Air fuel ratio sensor heater |
| Frequency of Operation | Continuous |
| Output duty cycle | 30% or higher |
| Output duty cycle | Higher than 0% |
| Output duty cycle | Less than 60% |
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the GTS on [A].
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and idle it for 5 minutes or more [B].
With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 2500 rpm for 1 minute [C].
During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform steps [C] and [D] after charging control has completed.
Idle the engine for 5 minutes or more [D].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0031, P0032 or P101D.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Refer to "Data List / Active Test" [A/F Heater Duty B1S1].
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage (Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
Inspect the air fuel ratio sensor.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Disconnect the air fuel ratio sensor connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C17-2 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
OK
NG
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C17-1 (HA1A) - C10-23 (HA1A) | Always | Below 1 Ω |
| C17-1 (HA1A) or C10-23 (HA1A) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P0031, P0032 or P101D is output | B |
A
B
Disconnect the air fuel ratio sensor connector.
Remove the No. 1 integration relay and ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Remove the ENG W/PMP relay connected between the checked terminals as the coil inside the relay influences the measurement value.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C17-2 (+B) - 2C-4 | Always | Below 1 Ω |
| C17-2 (+B) or 2C-4 - Body ground | Always | 10 kΩ or higher |
OK
NG