Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P106A  Evaporative Emission System Pressure Sensor - Manifold Absolute Pressure Correlation  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
P106A The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and manifold absolute pressure sensor (MAP*) is higher than 8.7 kPa [65.259 mmHg] (2 trip detection logic).
·

Canister pressure sensor (canister pump module)

·

Manifold absolute pressure sensor



HINT:

*: Data List name


MONITOR DESCRIPTION

This DTC is designed to detect a deviation in the output characteristics of a pressure sensor.

The pressure of the canister pressure sensor and manifold absolute pressure sensor is monitored 50 minutes after the power switch is turned off. If there is a difference in the pressures, the MIL is illuminated (2 trip detection logic).

HINT:

Correct judgment may not be possible when the altitude is 4000 m (13124 ft) or higher.


MONITOR STRATEGY

Required Sensors/Components (Main) Canister pressure sensor
Manifold absolute pressure sensor
Required Sensors/Components (Related) -
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Put the engine in inspection mode (maintenance mode) [A].

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

5.

Start the engine and idle for 10 seconds.

6.

Turn the power switch off.

7.

Leave the power switch off for 55 minutes [B].

8.

Turn the power switch on (IG) and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P106A.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [C] again.




CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Vapor Pressure Pump and MAP].

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P106A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P106A is output A
DTC P106A and other DTCs are output B

HINT:

If any DTCs other than P106A are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (VAPOR PRESSURE PUMP AND MAP)

B

2.READ VALUE USING GTS (VAPOR PRESSURE PUMP AND MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Vapor Pressure Pump and MAP.


e.

Compare the Vapor Pressure Pump and MAP data from the Data List with day's atmospheric pressure*.

HINT:
·

*: Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)]. For every 100 m (328 ft) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.

·

If you do not know the atmospheric pressure refer to the Vapor Pressure Pump value of other vehicles in the workshop and check the difference in pressure.



Result
Result Proceed to
If the Vapor Pressure Pump value differs from the atmospheric pressure by 3.5 kPa [26.254 mmHg] or higher A
If the MAP value differs from the atmospheric pressure by 3.5 kPa [26.254 mmHg] or higher B



A

3.REPLACE CANISTER PUMP MODULE

B

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
3.REPLACE CANISTER PUMP MODULE

NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.

Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>VACUUM SENSOR>REMOVAL



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Vapor Pressure Pump and MAP.


d.

Confirm that the difference between Vapor Pressure Pump and MAP are 3.5 kPa [26.25 mmHg] or less.



NEXT

END