Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P261B  Engine Coolant Pump "B" Control Malfunction  P261C  Engine Coolant Pump "B" Control Circuit Low  P261D  Engine Coolant Pump "B" Control Circuit High  


DESCRIPTION

The ECM controls the engine water pump assembly by calculating the necessary amount of coolant flow based on engine coolant temperature, engine speed and vehicle speed information. The speed of the engine water pump assembly is controlled steplessly using a duty cycle signal sent from the ECM. This optimal control enhances warm-up performance and reduces cooling losses, thus reducing the specific fuel consumption of the engine.

DTC No. DTC Detection Condition Trouble Area
P261B Engine water pump assembly speed is less than 900 rpm while the engine water pump assembly is operating (1 trip detection logic).
·

Open or short in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM


P261C Engine water pump assembly output voltage is less than specified value while the engine water pump assembly is operating (1 trip detection logic).
·

Open or short in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM


P261D Engine water pump assembly output voltage is higher than specified value while the engine water pump assembly is operating (1 trip detection logic).
·

Short in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM



MONITOR DESCRIPTION

The ECM calculates the speed of the engine water pump assembly using a duty cycle signal sent from the engine water pump assembly. When the speed of the engine water pump assembly becomes less than 900 rpm while it is operating, the ECM detects the malfunction and stores DTC P261B.

The engine water pump assembly operates steplessly based on a duty cycle signal sent from the ECM. If actual drive duty cycle ratio does not correspond to the target drive duty cycle of the engine water pump assembly, the ECM detects the malfunction.

MONITOR STRATEGY

Required Sensors/Components (Main) Engine water pump assembly
Required Sensors/Components (Related) -
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher).

8.

Idle the engine for 20 seconds or more [A].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P261B, P261C or P261D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A275613E09
4.313,1.469 5.625,1.833 1.313,0.365 10 false Engine Water Pump Assembly 4.313,1.313 4.635,1.5 0.323,0.188 10 false C27 5.156,0.396 5.51,0.573 0.354,0.177 10 false SWP 4.354,0.396 4.708,0.573 0.354,0.177 10 false +B 5.177,0.979 5.521,1.135 0.344,0.156 10 false NWP 5.583,0.865 5.719,1.042 0.135,0.177 10 false 2 4.198,0.865 4.333,1.042 0.135,0.177 10 false 5 4.198,0.26 4.333,0.438 0.135,0.177 10 false 1 5.583,0.271 5.719,0.448 0.135,0.177 10 false 4 4.344,0.99 4.854,1.198 0.51,0.208 10 false PGND 5.875,0.865 6.104,1.031 0.229,0.167 10 false 28 5.875,0.271 6.104,0.438 0.229,0.167 10 false 29 6.125,1.01 6.458,1.177 0.333,0.167 10 false WPI 6.125,0.396 6.5,0.563 0.375,0.167 10 false WPO 6.135,3.656 6.708,3.927 0.573,0.271 10 false MREL 5.844,3.51 6.083,3.677 0.24,0.167 10 false 46 6.438,4.25 6.802,4.427 0.365,0.177 10 false ECM 1.802,1.083 2.885,1.427 1.083,0.344 10 false ENG W/PMP 0.875,0.531 1.719,0.688 0.844,0.156 10 false ENG W/PMP 1.885,0.719 2.031,0.906 0.146,0.188 10 false 2 2.438,0.719 2.583,0.865 0.146,0.146 10 false 1 2.438,0.26 2.563,0.438 0.125,0.177 10 false 3 1.885,0.26 1.99,0.427 0.104,0.167 10 false 5 1.875,2.365 2.552,2.677 0.677,0.313 10 false EFI-MAIN 0.552,4.292 0.917,4.49 0.365,0.198 10 false MAIN 0.677,4.948 1.74,5.135 1.063,0.188 10 false Auxiliary Battery 6.146,4.25 6.448,4.438 0.302,0.188 10 false A40 1.427,3.021 2.521,3.417 1.094,0.396 10 false No. 1 Integration Relay 1.25,2.792 1.479,2.969 0.229,0.177 10 false 2C 1.344,1.396 1.573,1.573 0.229,0.177 10 false 2C 1.552,2.792 1.698,2.958 0.146,0.167 10 false 3 2.531,2.792 2.771,2.958 0.24,0.167 10 false 2E 2.813,2.792 2.969,2.958 0.156,0.167 10 false 1 3.094,2.115 3.292,2.281 0.198,0.167 10 false 2C 3.156,1.938 3.281,2.094 0.125,0.156 10 false 2 1.646,1.406 1.802,1.563 0.156,0.156 10 false 4 1.521,4.073 1.792,4.271 0.271,0.198 10 false P/I 2.688,2.417 3.365,2.594 0.677,0.177 10 false EFI-MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ELECTRIC WATER PUMP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch no (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Electric Water Pump.


e.

Touch the engine water pump and check that the pump assembly is operating (vibrating).

OK:

The engine water pump assembly is operating (vibrating).




OK

2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENGINE WATER PUMP ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)
HINT:

Confirm a good connection at the engine water pump assembly and ECM connectors.


a.

Disconnect the engine water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C27-2 (NWP) - A40-28 (WPI) Always Below 1 Ω
C27-4 (SWP) - A40-29 (WPO) Always Below 1 Ω
C27-2 (NWP) or A40-28 (WPI) - Body ground Always 10 kΩ or higher
C27-4 (SWP) or A40-29 (WPO) - Body ground Always 10 kΩ or higher




OK

3.CHECK TERMINAL VOLTAGE (WPI VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (WPI VOLTAGE)
a.
U158872E02
1.719,2.021 2.375,1.635 false 0.563,2.021 0.833,2.198 0.271,0.177 10 false C27 2.427,1.542 2.865,1.75 0.438,0.208 10 false NWP 0.479,0.146 0.688,0.365 0.208,0.219 10 false *a

Disconnect the engine water pump assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C27-2 (NWP) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Engine Water Pump Assembly)



OK

REPLACE ENGINE WATER PUMP ASSEMBLY

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENGINE WATER PUMP ASSEMBLY)
HINT:

Confirm a good connection at the engine water pump assembly and ECM connectors.


a.
U158873E02
1.417,2.094 1.115,2.708 false 0.594,2.094 0.865,2.271 0.271,0.177 10 false C27 0.969,2.729 1.208,2.938 0.24,0.208 10 false +B 0.188,0.135 0.396,0.354 0.208,0.219 10 false *a

Disconnect the engine water pump assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C27-1 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Engine Water Pump Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND)

NG

9.INSPECT RELAY (ENG W/PMP RELAY)
5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the engine water pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C27-5 (PGND) - Body ground Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the engine water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C27-2 (NWP) - A40-28 (WPI) Always Below 1 Ω
C27-4 (SWP) - A40-29 (WPO) Always Below 1 Ω
C27-2 (NWP) or A40-28 (WPI) - Body ground Always 10 kΩ or higher
C27-4 (SWP) or A40-29 (WPO) - Body ground Always 10 kΩ or higher




OK

7.REPLACE ENGINE WATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ENGINE WATER PUMP ASSEMBLY
a.

Replace the engine water pump assembly.

Click hereEngine / Hybrid System>1NZ-FXE (COOLING)>WATER PUMP>REMOVAL



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC P261B, P261C or P261D is output A
DTCs are not output B



A

B

END

9.INSPECT RELAY (ENG W/PMP RELAY)
a.
A234567E01
2.32,0.531 2.424,0.680 0.104,0.149 10 2 2.32,1.557 2.424,1.706 0.104,0.149 10 1 2.755,0.531 2.858,0.680 0.104,0.149 10 3 2.755,1.557 2.858,1.706 0.104,0.149 10 5 2.375,0.9 2.375,0.689 false 2.373,1.318 2.373,1.557 false 2.628,1.218 2.792,1.557 false 2.899,1 2.8,0.695 false

Remove the ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 No auxiliary battery voltage applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω




OK

10.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - ENGINE WATER PUMP ASSEMBLY)

NG

REPLACE RELAY (ENG W/PMP RELAY)

10.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - ENGINE WATER PUMP ASSEMBLY)
a.

Remove the ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the engine water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ENG W/PMP relay terminal 3 - C27-1 (+B) Always Below 1 Ω
ENG W/PMP relay terminal 3 or C27-1 (+B) - Body ground Always 10 kΩ or higher




OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENG W/PMP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENG W/PMP RELAY)
a.
A268185E01
0.286,0.307 0.522,0.472 0.236,0.165 10 *1 0.913,3.277 1.150,3.443 0.236,0.165 10 *2

Remove the ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ENG W/PMP relay terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 ENG W/PMP Relay



OK

12.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - ENG W/PMP RELAY)

12.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - BODY GROUND)
a.

Remove the ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ENG W/PMP relay terminal 1 - Body ground Always Below 1 Ω




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENG W/PMP RELAY - EFI-MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR