Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL PUMP(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0320554 FUEL PUMP(w/ Canister Pump Module) A

1NZ-FXE FUEL  FUEL PUMP(w/ Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.
A267904C01
0.931,1.511 1.102,1.673 0.170,0.162 10 *a 0.659,2.504 0.829,2.666 0.170,0.162 10 *b 1.023,1.112 1.023,1.524 false 1.875,2.598 0.868,2.598 false
*a Protrusion
*b Notch


Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.

Align the protrusion of the fuel suction tube with pump and gauge assembly with the notch of the fuel tank assembly.


d.
A395719C01
0.958,1.823 1.083,1.823 1.083,1.823 1.24,1.354 true 0.76,1.74 0.948,1.896 0.188,0.156 10 true *a
*a Paint Mark


Place a paint mark on the fuel suction tube with pump and gauge assembly as shown in the illustration.

HINT:

Perform this step only when replacing the fuel suction tube with pump and gauge assembly.



Hide 77169A 2.INSTALL FUEL PUMP GAUGE RETAINER

a.
A395720C01
0.635,2.865 0.906,2.865 true 1.229,3.094 1.396,2.667 1.396,2.667 1.531,2.667 true 0.938,2.906 0.802,3.229 0.802,3.229 1.229,3.125 true 0.406,2.76 0.583,2.917 0.177,0.156 10 true *a 1.563,2.583 1.74,2.74 0.177,0.156 10 true *b 0.646,3.229 0.813,3.417 0.167,0.188 10 true *c
*a Copy of Start of Threads Mark
*b Start of Threads of the Fuel Pump Gauge Retainer
*c Align
V100135

Press down
V100136

Front


Align the start of the threads of a new fuel pump gauge retainer with the start of threads mark that was copied onto the vehicle body and while pushing down the fuel suction tube with pump and gauge assembly, attach the fuel pump gauge retainer.


b.

Install SST to the fuel pump gauge retainer.

i.
A381189C02
2.115,0.208 2.26,0.208 2.26,0.208 2.385,0.375 false 0.604,1.24 0.906,1.24 false 1.208,1.385 1.51,1.385 false 1.177,2.167 1.406,2.167 false 1.115,2.406 1.229,2.406 1.229,2.406 1.563,2.573 true 1.854,2.573 1.99,2.344 1.99,2.344 2.083,2.344 false 1.104,3.104 1.292,3.104 1.292,3.104 1.563,2.677 true 0.563,4.458 0.75,4.458 0.75,4.458 1.385,4.042 true 2.604,1.708 2.604,1.469 false 1.563,1.313 1.875,1.469 0.313,0.156 10 false *1 0.438,1.156 0.75,1.313 0.313,0.156 10 false *a 0.917,3.031 1.229,3.188 0.313,0.156 10 false *b 0.938,2.333 1.25,2.49 0.313,0.156 10 false *c 0.375,4.396 0.688,4.552 0.313,0.156 10 false *d 1.948,0.146 2.26,0.302 0.313,0.156 10 false *1 1.01,2.083 1.323,2.24 0.313,0.156 10 false *a 2.146,2.281 2.458,2.438 0.313,0.156 10 false *1 2.531,1.729 2.844,1.885 0.313,0.156 10 false *a
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Protrusion
*c Notch
*d Do not install SST (Claw Set)


Set 4 SST (claw set) to the fuel pump gauge retainer.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the notch of SST (claw set) with the protrusion of the fuel pump gauge retainer.

·

Do not install SST (claw set) to the start of threads location of the fuel pump gauge retainer.




ii.
A381190C02
1.031,0.396 1.302,0.396 false 0.927,2.052 1.063,2.052 1.063,2.052 1.229,1.823 false 2.135,1.302 2.24,1.052 2.24,1.052 2.344,1.052 false 2.406,0.979 2.719,1.135 0.313,0.156 10 false *1 0.844,0.313 1.156,0.469 0.313,0.156 10 false *a 0.75,1.979 1.063,2.135 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Push
V100136

SST (Bolt)


Push SST (claw set) against the fuel pump gauge retainer and tighten SST (bolt).


iii.
A395714C01
0.729,0.833 0.854,0.833 0.854,0.833 1.25,1.01 true 0.656,1.51 0.906,1.51 true 0.781,1.979 0.906,1.979 0.906,1.979 1.167,1.885 true 2.302,1.896 2.625,1.896 true 2.042,0.99 2.5,0.781 2.5,0.781 2.625,0.781 true 0.469,1.417 0.667,1.573 0.198,0.156 10 true *a 0.552,0.74 0.719,0.906 0.167,0.167 10 true *b 0.615,1.885 0.781,2.052 0.167,0.167 10 true *b 2.656,1.813 2.823,1.979 0.167,0.167 10 true *b 2.656,0.708 2.823,0.875 0.167,0.167 10 true *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SST (bolt).

SST
09808-14031  (09808-01030, 09808-01090)


iv.
A395715C01
2.24,0.219 2.063,0.219 2.063,0.219 1.719,1.104 true 0.802,0.625 1.323,0.625 true 2.26,0.156 2.458,0.313 0.198,0.156 10 true *a 0.604,0.552 0.781,0.729 0.177,0.177 10 true *b
*a Center Point of Fuel Pump Gauge Retainer
*b SST (Plate)
V100135

Front


Adjust the position of SST (claw set) so that the hole in SST (plate) for installing SST (handle) is in the center of the fuel pump gauge retainer.


v.
A395716C01
1.177,0.292 1.344,0.292 1.344,0.292 1.667,0.75 true 0.906,0.521 1.063,0.521 1.063,0.521 1.302,0.885 true 1.167,1.667 1.302,1.667 1.302,1.667 1.542,1.573 true 1.354,1.906 1.5,1.906 1.5,1.906 1.844,1.719 true 1.156,1.813 1.344,1.969 0.188,0.156 10 true *1 0.729,0.427 1.042,0.583 0.313,0.156 10 false *a 0.979,1.583 1.167,1.74 0.188,0.156 10 true *b 1.01,0.188 1.323,0.344 0.313,0.156 10 false *c
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
V100135

Press


Press SST (claw set) against the rib of the fuel pump gauge retainer and tighten SST (bolt).



c.
A396879C01
0.979,3.01 1.083,3.01 1.083,3.01 1.146,3.094 false 0.906,3.667 1.146,3.667 false 0.875,1.75 0.74,1.458 0.74,1.458 1.24,1.583 true 1.75,2.708 1.875,2.708 1.875,2.708 1.99,3 true 0.813,2.927 1.125,3.083 0.313,0.156 10 false *1 0.74,3.583 1.052,3.74 0.313,0.156 10 false *2 1.583,2.615 1.771,2.771 0.188,0.156 10 true *a 1.469,0.365 1.656,0.531 0.188,0.167 10 true *b 1.677,2.302 1.865,2.469 0.188,0.167 10 true *c 0.698,3.958 1.01,4.115 0.313,0.156 10 false *d 0.552,1.354 0.729,1.51 0.177,0.156 10 true *e
*1 Fuel Pump Gauge Retainer
*2 Fuel Tank Assembly
*a SST (Plate)
*b Tighten approximately 90°
*c Fuel pump gauge retainer rises up
*d Cross Section
*e Paint Mark
V100135

Press quickly and firmly
V100136

Front


While pressing down on the fuel suction tube with pump and gauge assembly, have another person firmly press the fuel pump gauge retainer against the threads of the fuel tank assembly, and tighten the fuel pump gauge retainer by approximately 90°.

NOTICE:
·

To prevent damage to parts, do not turn SST too vigorously.

·

Do not turn the fuel pump gauge retainer if the paint marks become misaligned.




d.

Quickly and firmly press down on the part of the fuel pump gauge retainer closest to the front of the vehicle to keep it from rising up.

HINT:
·

If the fuel pump gauge retainer cannot be properly pressed down due to the position of SST, set SST in a different position.

·

When fully pressing down the fuel pump gauge retainer, there will be a sound or tactile sensation of parts contacting each other, and at this point the fuel suction tube with pump and gauge assembly will stop rising up.




e.
A396880C01
0.698,1.823 0.865,1.823 0.865,1.823 1.396,1.531 true 0.667,2.906 0.927,2.906 true 0.531,1.719 0.844,1.875 0.313,0.156 10 false *a 1.063,1.021 1.375,1.177 0.313,0.156 10 false *b 1.542,0.552 1.854,0.708 0.313,0.156 10 false *c 0.479,2.813 0.646,3 0.167,0.188 10 true *d 2.188,1.219 2.5,1.375 0.313,0.156 10 false *b 2.115,0.656 2.427,0.813 0.313,0.156 10 false *c
*a SST (Plate)
*b One Person in Charge of Tightening
*c One Person in Charge of Pressing Down
*d Copy of Start of Threads Mark
V100135

Front


While pressing down on the fuel suction tube with pump and gauge assembly, have another person slowly tighten the fuel pump gauge retainer until it reaches the start of threads mark.


f.
A396881C01
0.635,1.177 0.948,1.177 true 1.844,0.344 1.99,0.344 1.99,0.344 2.115,0.719 true 2.052,2.073 2.052,2.354 true 1.167,2.844 1.292,2.844 1.292,2.844 1.448,3.156 false 1.24,3.917 1.521,3.917 false 2.292,2.969 2.625,2.969 false 0.979,2.76 1.292,2.917 0.313,0.156 10 false *1 1.063,3.823 1.375,3.979 0.313,0.156 10 false *2 0.469,1.083 0.656,1.24 0.188,0.156 10 true *a 2.688,2.896 3,3.052 0.313,0.156 10 false *b 1.646,0.25 1.833,0.406 0.188,0.156 10 true *a 1.969,2.365 2.156,2.521 0.188,0.156 10 true *a 2.135,1.125 2.281,1.281 0.146,0.156 10 true A 2.49,0.677 2.635,0.833 0.146,0.156 10 true A 1.438,4.396 2.208,4.594 0.771,0.198 10 false A - A
*1 Fuel Pump Gauge Retainer
*2 Fuel Tank Assembly
*a Measurement Position
*b Vernier Caliper
V100136

Front


Check the tightening status of the fuel pump gauge retainer.

i.

Using a vernier caliper, measure the distance from the fuel tank assembly to the upper surface of the fuel pump gauge retainer at 3 positions as shown in the illustration.

Standard:

Difference between the 3 measured values is 3 mm (0.118 in.) or less.


NOTICE:

If the difference between measurements is approximately 6 mm (0.236 in.), the threads are cross-threaded by 1 row (6 mm (0.236 in.)), so remove and reinstall the fuel pump gauge retainer.




g.
A396882C01
0.927,0.313 1.083,0.313 1.083,0.313 1.198,0.802 false 0.875,1.448 1.417,1.448 true 0.76,0.219 1.073,0.375 0.313,0.156 10 false *a 0.698,1.354 1.01,1.51 0.313,0.156 10 false *b 0.563,0.698 0.875,0.854 0.313,0.156 10 false *c 1.469,0.604 1.781,0.76 0.313,0.156 10 false *d 1.552,2.594 1.729,2.771 0.177,0.177 10 true *e 2.802,1.042 3.115,1.198 0.313,0.156 10 false *c 2,0.708 2.313,0.865 0.313,0.156 10 false *d
*a SST (Handle)
*b SST (Plate)
*c One Person in Charge of Tightening
*d One Person in Charge of Pressing Down
*e Approximately 90°
V100135

Front


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


h.

While pressing down on the fuel suction tube with pump and gauge assembly, have another person use SST (handle) to slowly tighten the fuel pump gauge retainer approximately 90°.


i.
A396883C01
0.729,0.542 0.896,0.542 0.896,0.542 1.135,0.844 true 1.688,0.354 1.854,0.354 1.854,0.354 2.115,0.604 true 2.417,4.406 2.938,4.406 true 2.625,4.135 2.823,4.135 2.823,4.135 2.823,4.396 true 2.188,4.021 1.969,4.302 1.969,4.302 1.969,4.427 true 1.51,0.26 1.677,0.417 0.167,0.156 10 true *a 0.552,0.448 0.729,0.615 0.177,0.167 10 true *b 2.979,4.344 3.177,4.5 0.198,0.156 10 true *c 1.885,4.458 2.063,4.615 0.177,0.156 10 true *d
*a SST (Handle)
*b SST (Plate)
*c Copy of Fully Tightened Mark
*d Start of Threads of the Fuel Pump Gauge Retainer
V100135

Tighten
V100136

Front


Slowly tighten the fuel pump gauge retainer until it reaches between the fully tightened marks that were copied onto the vehicle body.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A408569C01
4.417,2 5.5,3.417 1.083,1.417 5.583,2 6.667,3.417 1.083,1.417 1.604,2.01 1.792,2.01 1.792,2.01 2.271,2.198 true 2.969,2.083 3.313,2.083 true 5.604,0.74 5.75,0.469 5.75,0.469 5.917,0.469 false 5.969,1.115 6.198,1.115 false 4.927,1.49 5.104,1.49 5.104,1.49 5.177,1.25 false 5.75,1.24 6.115,1.24 6.115,1.24 6.115,1.354 false 5.75,1.354 6.26,1.354 false 5.021,2.583 5.208,2.583 false 4.823,2.708 4.969,3.094 4.969,3.094 5.083,3.094 true 5.938,2.615 6.063,2.281 6.063,2.281 6.208,2.281 true 6.125,2.646 6.365,2.646 false 4.75,1.417 5.063,1.573 0.313,0.156 10 false *1 6.25,1.042 6.563,1.198 0.313,0.156 10 false *2 1.438,1.938 1.75,2.094 0.313,0.156 10 false *3 5.979,0.375 6.292,0.531 0.313,0.156 10 false *a 6.313,1.271 6.625,1.427 0.313,0.156 10 false *b 4.448,2.01 4.76,2.167 0.313,0.156 10 false *c 5.625,2.01 5.938,2.167 0.313,0.156 10 false *d 5.146,3 5.458,3.156 0.313,0.156 10 false *e 5.26,2.51 5.573,2.667 0.313,0.156 10 false *2 6.396,2.573 6.708,2.729 0.313,0.156 10 false *2 3.375,2 3.688,2.156 0.313,0.156 10 false *2 6.26,2.198 6.573,2.354 0.313,0.156 10 false *e
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
*e Collar - -


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 77404 4.CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.
U159071C01
2.438,0.365 2.583,0.219 2.583,0.219 2.688,0.219 false 2.74,0.125 2.927,0.313 0.188,0.188 10 false *a
*a Retainer
V100135

Push


Push in the fuel tank vent hose connector to the fuel suction tube with pump and gauge assembly and push the retainer so that the claws are engaged.

NOTICE:
·

Check that there is no damage or foreign matter around the connecting parts of the fuel tank vent hose connector and fuel suction tube with pump and gauge assembly before performing this work.

·

After connecting the fuel tank vent hose sub-assembly, check that the fuel tank vent hose sub-assembly is securely connected by pulling on the fuel tank vent hose connector.




Hide 5. CHECK AIRTIGHTNESS

a.
A396884C01
0.813,1.448 1.26,1.448 true 0.646,1.354 0.813,1.51 0.167,0.156 10 true *a
*a Soapy Water Application Area


After installing the fuel suction tube with pump and gauge assembly, check for fuel leaks by first applying soapy water to the area where the fuel suction plate sub-assembly and fuel pump gauge retainer contact, and then blow forcibly into the fuel inlet area through a flexible pouring spout or similar tube.

NOTICE:

Cover the connector of the fuel suction tube with pump and gauge assembly with protective tape.



b.
A366416C01
3.135,0.75 3.313,0.906 0.177,0.156 10 true *a
*a Air


Blow forcibly until the reverse flow prevention valve inside the fuel inlet activates.

CAUTION:

Be careful not to inhale any fuel vapor.


HINT:

There should be a faintly audible sound when the reverse flow prevention valve operates.



c.

Check that the contact areas between the fuel suction tube with pump and gauge assembly and fuel pump gauge retainer are airtight.

NOTICE:
·

If air bubbles appear, remove and reinstall the fuel pump gauge retainer.

·

After a fuel pump gauge retainer and fuel suction tube set gasket have been used once, replace them with new parts.

·

When removing and reinstalling the fuel pump gauge retainer, make sure to clean away the soapy water to prevent the fuel suction tube set gasket from slipping out of position and being assembled incorrectly.



HINT:
A396885C01
0.885,1.635 1.365,1.635 true 0.729,1.552 0.896,1.719 0.167,0.167 10 true *a
*a Air Bubbles


If the assembled components are not airtight due to improper installation of the fuel pump gauge retainer, etc., air bubbles will appear as shown in the illustration.



Hide 6.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58325E 8.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the fuel pump connector.


d.
A267868C03
2.219,0.729 2.74,0.198 2.74,0.198 2.896,0.198 false 2.938,0.104 3.146,0.354 0.208,0.25 10 false *a
*a Butyl Tape


Install the rear floor service hole cover with new butyl tape.


Hide 73705B 9.INSTALL CROSS ANCHOR BRACKET SUB-ASSEMBLY