Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2017.06–2019.07
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


U183350C01
3.104,0.177 3.292,0.344 0.188,0.167 10 false J1 3.375,0.177 3.573,0.344 0.198,0.167 10 false *A 3.708,0.188 3.917,0.354 0.208,0.167 10 false H1 4.021,0.167 4.219,0.333 0.198,0.167 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J1*1, H1*2 power window regulator master switch assembly connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

for LHD and w/o Canister Pump Module
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-1 (E) - Body ground LA - Body ground Ground Always Below 1 Ω
J1-6 (B) - J1-1 (E) LA-GR - LA Power supply Power switch on (IG) 11 to 14 V

for LHD and w/ Canister Pump Module
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-1 (E) - Body ground LA - Body ground Ground Always Below 1 Ω
J1-7 (B) - J1-1 (E) LA-GR - LA Power supply Power switch on (IG) 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H1-9 (E) - Body ground LA - Body ground Ground Always Below 1 Ω
H1-6 (B) - H1-9 (E) LA-GR - LA Power supply Power switch on (IG) 11 to 14 V


c.

Reconnect the J1*1, H1*2 power window regulator master switch assembly.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD and w/o Canister Pump Module
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-8 (U) - J1-1 (E) R - LA Power window motor UP output Power switch on (IG), driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
J1-4 (AUTO) - J1-1 (E) R - LA Power window motor AUTO UP output Power switch on (IG), driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Power window motor AUTO DOWN output Power switch on (IG), driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open 11 to 14 V → Below 1 V → 11 to 14 V
J1-5 (D) - J1-1 (E) G - LA Power window motor DOWN output Power switch on (IG), driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
J1-16 (U) - J1-1 (E) LA-W - LA Power window motor UP output Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J1-15 (D) - J1-1 (E) LA-P - LA Power window motor DOWN output Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
J1-12 (U) - J1-1 (E) LA-Y - LA Power window motor UP output Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J1-13 (D) - J1-1 (E) LA-B - LA Power window motor DOWN output Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
J1-10 (U) - J1-1 (E) LA-R - LA Power window motor UP output Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J1-18 (D) - J1-1 (E) LA-G - LA Power window motor DOWN output Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

for LHD and w/ Canister Pump Module
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-6 (U) - J1-1 (E) R - LA Power window motor UP output Power switch on (IG), driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
J1-4 (AUTO) - J1-1 (E) R - LA Power window motor AUTO UP output Power switch on (IG), driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Power window motor AUTO DOWN output Power switch on (IG), driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open 11 to 14 V → Below 1 V → 11 to 14 V
J1-3 (D) - J1-1 (E) G - LA Power window motor DOWN output Power switch on (IG), driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
J1-10 (U) - J1-1 (E) LA-W - LA Power window motor UP output Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J1-18 (D) - J1-1 (E) LA-P - LA Power window motor DOWN output Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
J1-12 (U) - J1-1 (E) LA-Y - LA Power window motor UP output Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J1-13 (D) - J1-1 (E) LA-B - LA Power window motor DOWN output Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
J1-15 (U) - J1-1 (E) LA-R - LA Power window motor UP output Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J1-16 (D) - J1-1 (E) LA-G - LA Power window motor DOWN output Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H1-1 (U) - H1-9 (E) G - LA Power window motor UP output Power switch on (IG), driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
H1-4 (AUTO) - H1-9 (E) R - LA Power window motor AUTO UP output Power switch on (IG), driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Power window motor AUTO DOWN output Power switch on (IG), driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open 11 to 14 V → Below 1 V → 11 to 14 V
H1-5 (D) - H1-9 (E) R - LA Power window motor DOWN output Power switch on (IG), driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
H1-12 (U) - H1-9 (E) LA-W - LA Power window motor UP output Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
H1-13 (D) - H1-9 (E) LA-P - LA Power window motor DOWN output Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
H1-18 (U) - H1-9 (E) LA-Y - LA Power window motor UP output Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
H1-10 (D) - H1-9 (E) LA-B - LA Power window motor DOWN output Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
H1-16 (U) - H1-9 (E) LA-R - LA Power window motor UP output Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
H1-15 (D) - H1-9 (E) LA-G - LA Power window motor DOWN output Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Door)


U183351C01
3.115,0.229 3.333,0.396 0.219,0.167 10 false H2 3.406,0.229 3.635,0.396 0.229,0.167 10 false *A 3.781,0.219 3.969,0.385 0.188,0.167 10 false J2 4.073,0.219 4.302,0.385 0.229,0.167 10 false *B
*A for LHD *B for RHD


a.

Disconnect the H2*1,J2*2 power window regulator switch assembly (for front passenger door) connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-3 (B) - Body ground LA-L - Body ground Power supply Power switch on (IG) 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-3 (B) - Body ground LA-L - Body ground Power supply Power switch on (IG) 11 to 14 V


c.

Reconnect the H2*1,J2*2 power window regulator switch assembly (for front passenger door).

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-4 (U) - Body ground LA-R - Body ground Power window motor UP output Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
H2-1 (D) - Body ground LA-G - Body ground Power window motor DOWN output Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-4 (U) - Body ground LA-R - Body ground Power window motor UP output Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J2-1 (D) - Body ground LA-G - Body ground Power window motor DOWN output Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Door)


U183352E02
3.49,0.198 3.677,0.365 0.188,0.167 10 false L1

a.

Disconnect the L1 power window regulator switch assembly (for rear LH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L1-3 (B) - Body ground LA-SB - Body ground Power supply Power switch on (IG) 11 to 14 V


c.

Reconnect the L1 power window regulator switch assembly (for rear LH door).


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L1-4 (U) - Body ground LA-Y - Body ground Power window motor UP output Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
L1-1 (D) - Body ground LA-B - Body ground Power window motor DOWN output Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Door)


U183353E02
3.521,0.177 3.729,0.344 0.208,0.167 10 false K1

a.

Disconnect the K1 power window regulator switch assembly (for rear RH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K1-3 (B) - Body ground LA-SB - Body ground Power supply Power switch on (IG) 11 to 14 V


c.

Reconnect the K1 power window regulator switch assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K1-4 (U) - Body ground LA-Y - Body ground Power window motor UP output Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
K1-1 (D) - Body ground LA-B - Body ground Power window motor DOWN output Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


U183414C01
2.125,0.563 2.313,0.74 0.188,0.177 10 false J3 2.427,0.552 2.594,0.729 0.167,0.177 10 false *A 2.427,1.052 2.594,1.229 0.167,0.177 10 false *B 2.115,1.052 2.323,1.229 0.208,0.177 10 false H3
*A for LHD *B for RHD


a.

Disconnect the J3*1, H3*2 power window regulator motor assembly (for driver door) connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J3-1 (GND) - Body ground LA - Body ground Ground Always Below 1 Ω
J3-2 (B) - Body ground LA-G - Body ground Power supply Power switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H3-1 (GND) - Body ground LA - Body ground Ground Always Below 1 Ω
H3-2 (B) - Body ground LA-LG - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the J3*1, H3*2 power window regulator motor assembly (for driver door) connector.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J3-4 (AUTO) - J3-1 (GND) R - LA Power window motor AUTO UP input Power switch on (IG), driver door power window fully open 11 to 14 V
J3-4 (AUTO) - J3-1 (GND) R - LA Power window motor AUTO UP input Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
J3-4 (AUTO) - J3-1 (GND) R - LA Power window motor AUTO UP input Power switch on (IG), driver door power window fully closed 11 to 14 V
J3-4 (AUTO) - J3-1 (GND) R - LA Power window motor AUTO DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
J3-4 (AUTO) - J3-1 (GND) R - LA Power window motor AUTO DOWN input Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
J3-4 (AUTO) - J3-1 (GND) R - LA Power window motor AUTO DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
J3-5 (LED) - J3-1 (GND) W - LA LED illumination signal Power switch on (IG) 11 to 14 V
J3-5 (LED) - J3-1 (GND) W - LA LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
J3-7 (DOWN) - J3-1 (GND) G - LA Power window motor DOWN input Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
J3-7 (DOWN) - J3-1 (GND) G - LA Power window motor DOWN input Power switch on (IG), driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
J3-7 (DOWN) - J3-1 (GND) G - LA Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
J3-7 (DOWN) - J3-1 (GND) G - LA Power window motor DOWN input Power switch on (IG), driver door power window regulator switch fully pushed down (Automatic position) Below 1 V
J3-7 (DOWN) - J3-1 (GND) G - LA Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
J3-10 (UP) - J3-1 (GND) R - LA Power window motor UP input Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
J3-10 (UP) - J3-1 (GND) R - LA Power window motor UP input Power switch on (IG), driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V
J3-10 (UP) - J3-1 (GND) R - LA Power window motor UP input Power switch on (IG), driver door power window fully open 11 to 14 V
J3-10 (UP) - J3-1 (GND) R - LA Power window motor UP input Power switch on (IG), driver door power window regulator switch fully pulled up (Automatic operation) Below 1 V
J3-10 (UP) - J3-1 (GND) R - LA Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H3-4 (AUTO) - H3-1 (GND) R - LA Power window motor AUTO UP input Power switch on (IG), driver door power window fully open 11 to 14 V
H3-4 (AUTO) - H3-1 (GND) R - LA Power window motor AUTO UP input Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
H3-4 (AUTO) - H3-1 (GND) R - LA Power window motor AUTO UP input Power switch on (IG), driver door power window fully closed 11 to 14 V
H3-4 (AUTO) - H3-1 (GND) R - LA Power window motor AUTO DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
H3-4 (AUTO) - H3-1 (GND) R - LA Power window motor AUTO DOWN input Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
H3-4 (AUTO) - H3-1 (GND) R - LA Power window motor AUTO DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
H3-5 (LED) - H3-1 (GND) W - LA LED illumination signal Power switch on (IG) 11 to 14 V
H3-5 (LED) - H3-1 (GND) W - LA LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
H3-7 (DOWN) - H3-1 (GND) R - LA Power window motor DOWN input Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
H3-7 (DOWN) - H3-1 (GND) R - LA Power window motor DOWN input Power switch on (IG), driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
H3-7 (DOWN) - H3-1 (GND) R - LA Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
H3-7 (DOWN) - H3-1 (GND) R - LA Power window motor DOWN input Power switch on (IG), driver door power window regulator switch fully pushed down (Automatic position) Below 1 V
H3-7 (DOWN) - H3-1 (GND) R - LA Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
H3-10 (UP) - H3-1 (GND) G - LA Power window motor UP input Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
H3-10 (UP) - H3-1 (GND) G - LA Power window motor UP input Power switch on (IG), driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V
H3-10 (UP) - H3-1 (GND) G - LA Power window motor UP input Power switch on (IG), driver door power window fully open 11 to 14 V
H3-10 (UP) - H3-1 (GND) G - LA Power window motor UP input Power switch on (IG), driver door power window regulator switch fully pulled up (Automatic operation) Below 1 V
H3-10 (UP) - H3-1 (GND) G - LA Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B479736C02
1.625,3.833 2.042,4.104 0.417,0.271 4.458,3.813 4.792,4.073 0.333,0.26 5.063,3.813 5.396,4.073 0.333,0.26 1.698,5.198 2.031,5.458 0.333,0.26 4.958,5.188 5.292,5.448 0.333,0.26 1.698,6.552 2.031,6.813 0.333,0.26 4.958,6.542 5.292,6.802 0.333,0.26 3.281,7.833 3.615,8.094 0.333,0.26 1.667,1.469 1.917,1.469 false 0.635,2.667 1.031,2.667 false 3.792,1.031 3.792,0.531 3.792,0.531 3.958,0.531 false 1.604,0.854 1.604,0.521 1.604,0.521 1.771,0.521 false 0.125,0.177 0.5,0.417 0.375,0.24 12 false *A 1.823,0.438 2.135,0.635 0.313,0.198 10 false *1 4,0.438 4.313,0.635 0.313,0.198 10 false MB 1.958,1.385 2.417,1.583 0.458,0.198 10 false G59 0.896,1.448 1.208,1.646 0.313,0.198 10 false 3D 0.906,2.031 1.219,2.229 0.313,0.198 10 false 3C 0.25,2.573 0.865,2.771 0.615,0.198 10 false 3E*B 0.26,2.75 0.875,2.948 0.615,0.198 10 false 3F*C 5.844,1.385 6.156,1.583 0.313,0.198 10 false 3B 5.844,2.031 6.156,2.229 0.313,0.198 10 false 3A 1.708,3.875 2.167,4.073 0.458,0.198 10 false G59 4.542,3.854 4.854,4.052 0.313,0.198 10 false 3E 4.854,3.854 5.167,4.052 0.313,0.198 10 false *B 5.146,3.854 5.458,4.052 0.313,0.198 10 false 3F 5.469,3.854 5.781,4.052 0.313,0.198 10 false *C 1.781,5.229 2.094,5.427 0.313,0.198 10 false 3D 5.042,5.219 5.354,5.417 0.313,0.198 10 false 3C 1.771,6.583 2.083,6.781 0.313,0.198 10 false 3B 5.042,6.573 5.354,6.771 0.313,0.198 10 false 3A 3.344,7.875 3.656,8.073 0.313,0.198 10 false MB
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


B479735C02
3.323,7.51 3.677,7.792 0.354,0.281 4.729,6.292 5.083,6.573 0.354,0.281 1.74,6.292 2.094,6.573 0.354,0.281 1.052,5.042 1.406,5.323 0.354,0.281 3.854,5.052 4.208,5.333 0.354,0.281 5.427,5 5.781,5.281 0.354,0.281 6.083,5 6.438,5.281 0.354,0.281 4.573,3.708 4.99,4.021 0.417,0.313 2.167,3.708 2.583,4.021 0.417,0.313 0.656,2.75 1.031,2.75 false 1.615,0.958 1.615,0.573 1.615,0.573 1.781,0.573 false 4,1.135 4,0.667 4,0.667 4.167,0.667 false 1.667,1.583 2,1.583 false 1.667,2.031 2,2.031 false 3.396,7.563 3.708,7.76 0.313,0.198 10 false MB 4.823,6.333 5.135,6.531 0.313,0.198 10 false 3A 1.823,6.344 2.135,6.542 0.313,0.198 10 false 3B 1.146,5.094 1.458,5.292 0.313,0.198 10 false 3D 3.948,5.104 4.26,5.302 0.313,0.198 10 false 3C 5.521,5.063 5.833,5.26 0.313,0.198 10 false 3E 5.833,5.083 6.146,5.281 0.313,0.198 10 false *B 6.177,5.052 6.49,5.25 0.313,0.198 10 false 3F 6.479,5.104 6.792,5.302 0.313,0.198 10 false *C 4.656,3.781 5.115,3.979 0.458,0.198 10 false G59 2.25,3.781 2.708,3.979 0.458,0.198 10 false G60 0.271,2.667 0.667,2.917 0.396,0.25 10 false 3E*B 0.271,2.844 0.667,3.094 0.396,0.25 10 false 3F*C 1.813,0.5 2.125,0.698 0.313,0.198 10 false *1 0.917,1.531 1.229,1.729 0.313,0.198 10 false 3D 4.208,0.594 4.521,0.792 0.313,0.198 10 false MB 2.042,1.5 2.5,1.698 0.458,0.198 10 false G59 2.042,1.958 2.5,2.156 0.458,0.198 10 false G60 0.917,2.135 1.229,2.333 0.313,0.198 10 false 3C 5.854,1.49 6.167,1.688 0.313,0.198 10 false 3B 5.854,2.167 6.167,2.365 0.313,0.198 10 false 3A 0.125,0.094 0.5,0.333 0.375,0.24 12 false *A
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-32 (IG) - Body ground - Power switch power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G59-2 (KOFF) - Body ground L - Body ground Power window relay operation signal Power switch on (IG) 11 to 14 V
G59-2 (KOFF) - Body ground L - Body ground Power window relay operation signal Approximately 43 seconds after power switch turned off Below 1 V
3D-36 (FLCY) - Body ground R - Body ground Front door courtesy switch LH input Front door LH open Below 1 V
3D-36 (FLCY) - Body ground R - Body ground Front door courtesy switch LH input Front door LH closed Pulse generation
G59-19 (FRCY) - Body ground R - Body ground Front door courtesy switch RH input Front door RH open Below 1 V
G59-19 (FRCY) - Body ground R - Body ground Front door courtesy switch RH input Front door RH closed Pulse generation