Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

This DTC is stored when the ECU built into the regulator motor determines that the power window regulator master switch assembly is stuck.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
DTC No. DTC Detection Condition Trouble Area
B2312
·

Power window regulator master switch assembly (for driver door) stuck

·

Power window regulator master switch assembly held in same position for more than 20 seconds


·

Power window regulator master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Wire harness or connector



WIRING DIAGRAM

for LHD


B281016E63
0.271,2.292 2.281,2.708 2.01,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,3.365 2.615,3.521 1.646,0.156 10 false : LIN Communication Line 0.417,0.531 1.323,0.875 0.906,0.344 10 false from Auxiliary Battery 1.854,0.667 2.469,0.823 0.615,0.156 10 false DOOR D 2.521,2.406 4.573,2.813 2.052,0.406 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.417 6.844,2.781 1.615,0.365 10 false Power Window Regulator Master Switch Assembly 2.521,2.25 3.531,2.406 1.01,0.156 10 false J3 5.229,2.25 5.948,2.406 0.719,0.156 10 false J1 1.635,1.594 2.01,1.75 0.375,0.156 10 false LIN2 2.833,1.448 3.094,1.604 0.26,0.156 10 false LIN 2.833,0.427 2.958,0.583 0.125,0.156 10 false B 3.802,0.427 4.208,0.583 0.406,0.156 10 false AUTO 5.375,0.521 5.802,0.677 0.427,0.156 10 false AUTO 5.375,1.031 5.51,1.188 0.135,0.156 10 false D 5.375,1.531 5.51,1.688 0.135,0.156 10 false U 5.375,1.833 5.51,1.99 0.135,0.156 10 false E 3.729,0.927 4.24,1.083 0.51,0.156 10 false DOWN 3.958,1.438 4.208,1.594 0.25,0.156 10 false UP 3.875,1.729 4.24,1.885 0.365,0.156 10 false GND 4.24,1.729 4.365,1.885 0.125,0.156 10 false 1 4.25,0.938 4.375,1.094 0.125,0.156 10 false 7 4.792,0.938 5.479,1.104 0.688,0.167 10 false 5*1, 3*2 4.781,1.448 5.281,1.604 0.5,0.156 10 false 8*1, 6*2 5.188,1.74 5.677,1.896 0.49,0.156 10 false 1 4.25,0.427 4.375,0.583 0.125,0.156 10 false 4 5.208,0.427 5.333,0.583 0.125,0.156 10 false 4 4.229,1.448 4.417,1.604 0.188,0.156 10 false 10 2.646,0.427 2.771,0.583 0.125,0.156 10 false 2 2.635,1.448 2.813,1.604 0.177,0.156 10 false 9 3.188,3.167 5.677,3.344 2.49,0.177 10 false *1: w/o Canister Pump Module 3.188,3.448 5.677,3.625 2.49,0.177 10 false *2: w/ Canister Pump Module


for RHD


B281016E65
0.271,2.292 2.281,2.708 2.01,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,3.365 2.615,3.521 1.646,0.156 10 false : LIN Communication Line 0.417,0.531 1.323,0.875 0.906,0.344 10 false from Auxiliary Battery 1.854,0.667 2.469,0.823 0.615,0.156 10 false DOOR D 2.521,2.406 4.573,2.813 2.052,0.406 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.406 6.844,2.771 1.615,0.365 10 false Power Window Regulator Master Switch Assembly 2.521,2.25 3.531,2.406 1.01,0.156 10 false H3 5.229,2.25 5.948,2.406 0.719,0.156 10 false H1 1.635,1.594 2.01,1.75 0.375,0.156 10 false LIN2 2.833,1.448 3.094,1.604 0.26,0.156 10 false LIN 2.833,0.427 2.958,0.583 0.125,0.156 10 false B 3.802,0.427 4.208,0.583 0.406,0.156 10 false AUTO 5.375,0.531 5.802,0.688 0.427,0.156 10 false AUTO 5.375,1.042 5.51,1.198 0.135,0.156 10 false D 5.375,1.542 5.51,1.698 0.135,0.156 10 false U 5.375,1.833 5.51,1.99 0.135,0.156 10 false E 3.729,0.927 4.24,1.083 0.51,0.156 10 false DOWN 3.958,1.438 4.208,1.594 0.25,0.156 10 false UP 3.875,1.729 4.24,1.885 0.365,0.156 10 false GND 4.25,1.729 4.375,1.885 0.125,0.156 10 false 1 4.25,0.938 4.375,1.094 0.125,0.156 10 false 7 5.177,0.917 5.302,1.073 0.125,0.156 10 false 5 5.177,1.438 5.677,1.594 0.5,0.156 10 false 1 5.188,1.729 5.677,1.885 0.49,0.156 10 false 9 4.25,0.427 4.375,0.583 0.125,0.156 10 false 4 5.188,0.427 5.313,0.583 0.125,0.156 10 false 4 4.25,1.448 4.438,1.604 0.188,0.156 10 false 10 2.646,0.427 2.771,0.583 0.125,0.156 10 false 2 2.635,1.448 2.813,1.604 0.177,0.156 10 false 9


CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 can be stored in the power window regulator motor assembly (for driver door).

·

If a power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC OUTPUT

OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

NG

2.READ VALUE USING GTS (DRIVER DOOR WINDOW MOTOR)
2.READ VALUE USING GTS (DRIVER DOOR WINDOW MOTOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / D-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

D-Door Motor
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal OFF or ON OFF: Driver door power window auto switch not operated
ON: Driver door power window auto switch operated
-
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not operated
ON: Driver door power window manual up switch operated
-
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not operated
ON: Driver door power window manual down switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
a.

Disconnect the power window regulator master switch assembly connector.


b.

Disconnect the power window regulator motor assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

i.

for LHD

Standard Resistance:
Tester Connection Condition Specified Condition
J1-8 (U) - Body ground*1
J1-6 (U) - Body Ground*2
Always 10 kΩ or higher
J1-5 (D) - Body ground*1
J1-3 (D) - Body ground*2
Always 10 kΩ or higher
J1-4 (AUTO) - Body ground Always 10 kΩ or higher
J3-10 (UP) - Body ground Always 10 kΩ or higher
J3-7 (DOWN) - Body ground Always 10 kΩ or higher
J3-4 (AUTO) - Body ground Always 10 kΩ or higher


*1: w/o Canister Pump Module

*2: w/ Canister Pump Module



ii.

for LHD

Standard Resistance:
Tester Connection Condition Specified Condition
H1-1 (U) - Body ground Always 10 kΩ or higher
H1-5 (D) - Body ground Always 10 kΩ or higher
H1-4 (AUTO) - Body ground Always 10 kΩ or higher
H3-10 (UP) - Body ground Always 10 kΩ or higher
H3-7 (DOWN) - Body ground Always 10 kΩ or higher
H3-4 (AUTO) - Body ground Always 10 kΩ or higher





OK

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B298969C24
1.052,0.854 1.094,1.667 false 2.344,0.854 2.313,1.667 false 1.906,1.76 2.198,2.604 false 1.677,1.792 1.5,2.583 false 1.219,1.802 0.958,2.604 false 1.635,0.854 2.01,1.667 false 1.167,2.958 1.521,1.771 false 0.198,0.083 0.385,0.271 0.188,0.188 10 false *a 0.927,0.677 1.229,0.865 0.302,0.188 10 false E*C 2.073,2.635 2.5,2.823 0.427,0.188 10 false AUTO 1.49,0.667 2.552,0.854 1.063,0.188 10 false D*B 0.802,2.635 1.344,2.833 0.542,0.198 10 false U*A 1.396,2.635 1.99,2.917 0.594,0.281 10 false D*A*C 2.208,0.656 3.271,0.844 1.063,0.188 10 false E*A*B 1.031,3 1.49,3.198 0.458,0.198 10 false U*B
*A for LHD and w/o Canister Pump Module
*B for LHD and w/ Canister Pump Module
*C for RHD
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

i.

for LHD

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (U) - 1 (E)*1
6 (U) - 1 (E)*2
Released 10 kΩ or higher
8 (U) - 4 (AUTO)*1
6 (U) - 4 (AUTO)*2
Released 10 kΩ or higher
4 (AUTO) - 1 (E) Released 10 kΩ or higher
5 (D) - 1 (E)*1
3 (D) - 1 (E)*2
Released 10 kΩ or higher
4 (AUTO) - 5 (D)*1
4 (AUTO) - 3 (D)*2
Released 10 kΩ or higher


*1: w/o Canister Pump Module

*2: w/ Canister Pump Module



ii.

for RHD

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (U) - 9 (E) Released 10 kΩ or higher
1 (U) - 4 (AUTO) Released 10 kΩ or higher
4 (AUTO) - 9 (E) Released 10 kΩ or higher
5 (D) - 9 (E) Released 10 kΩ or higher
4 (AUTO) - 5 (D) Released 10 kΩ or higher





OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY