Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light.

WIRING DIAGRAM

E333937E07
0.354,0.906 1.25,1.323 0.896,0.417 10 false from Auxiliary Battery 1.844,1.104 2.406,1.333 0.563,0.229 10 false DC/DC 0.458,3.188 1.021,3.417 0.563,0.229 10 false M5 0.458,3.365 2.885,3.615 2.427,0.25 10 false Rear Combination Light Assembly LH 4.531,1.646 4.99,1.865 0.458,0.219 10 false TAIL 5.292,1.5 5.75,1.719 0.458,0.219 10 false TAIL 4.417,3.146 5.125,3.375 0.708,0.229 10 false FOG RR 5.438,4.156 5.896,4.375 0.458,0.219 10 false MB 5.438,4.333 7.104,4.74 1.667,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 3.354,3.833 6.094,4.094 2.74,0.26 10 false Instrument Panel Junction Block Assembly 3,0.958 3.281,1.198 0.281,0.24 10 false 3E 3,2.865 3.281,3.104 0.281,0.24 10 false 3D 3.042,0.76 3.26,0.99 0.219,0.229 10 false 1 3.021,2.667 3.344,2.906 0.323,0.24 10 false 3 6.063,0.865 6.281,1.094 0.219,0.229 10 false 14 6.063,2.354 6.281,2.583 0.219,0.229 10 false 27 1.781,2.854 1.969,3.104 0.188,0.25 10 false B 1.25,2.854 1.438,3.104 0.188,0.25 10 false E 1.052,2.771 1.24,3.021 0.188,0.25 10 false 1 1.979,2.771 2.198,3 0.219,0.229 10 false 6 6.323,0.948 6.781,1.167 0.458,0.219 10 false TRLY 6.313,2.458 6.771,2.677 0.458,0.219 10 false RFGO 5.146,3.01 5.854,3.24 0.708,0.229 10 false FOG RR

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.




OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light OFF or ON Light control switch is in tail position

OK:

Rear fog light relay operates. (Rear fog light illuminates.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the M5 rear combination light assembly LH connector.


b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-6 (B) - 3D-3 Always Below 1 Ω
M5-6 (B) or 3D-3 - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-1 (E) - Body ground Always Below 1 Ω




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E345461C09
1.781,0.354 2.177,0.625 0.396,0.271 5.021,0.396 5.417,0.667 0.396,0.271 3.354,2.229 3.75,2.5 0.396,0.271 2.854,3.292 3.271,2.875 false 4.365,3.281 4.781,2.865 false 1.896,0.417 2.271,0.688 0.375,0.271 10 false 3E 5.146,0.469 5.521,0.74 0.375,0.271 10 false 3D 3.458,2.302 3.833,2.573 0.375,0.271 10 false MB 2.677,3.323 3.219,3.594 0.542,0.271 10 false TRLY 4.229,3.313 4.771,3.583 0.542,0.271 10 false RFGO 0.375,0.24 0.75,0.51 0.375,0.271 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the auxiliary battery to terminal 3E-1.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14 (TRLY) and MB-27 (RFGO).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3D-3 - Auxiliary battery negative (-) terminal Always 11 to 14 V




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY