1. PRECAUTION
Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
62211
2.REMOVE FRONT PILLAR GARNISH RH
82142A
3.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *a | Slider |
Slide the slider to release the lock, and then disconnect the connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
82142A
4.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *a | Slider |
Slide the 2 sliders to release the locks, and then disconnect the 2 connectors.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
5.REMOVE UPPER INSTRUMENT PANEL ASSEMBLY
6.REMOVE NO. 2 HEATER TO REGISTER DUCT ASSEMBLY
73960A
7.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/o Occupant Classification System)
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
Remove the 2 screws.
Disengage the clamp from the upper instrument panel assembly.
Lean the upper instrument panel assembly and disengage the 3 hooks.
Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the upper instrument panel assembly.
73960A
8.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Occupant Classification System)
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
Disengage the clamp from the upper instrument panel assembly.
Disengage the clamp to separate the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.
Remove the 2 screws.
Lean the upper instrument panel assembly and disengage the 3 hooks.
Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the upper instrument panel assembly.
82142A
9.REMOVE NO. 2 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)
| *a | Protective Tape |
| *b | Airbag Connector |
| *c | Airbag Connector Lock |
Separate the No. 2 instrument panel wire from the instrument panel passenger airbag assembly clamp.
Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.
Disconnect the airbag connector to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
82142A
10.REMOVE NO. 2 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)
| *a | Protective Tape |
| *b | Vent Hole Connector |
| *c | Vent Hole Connector Lock |
Using a screwdriver with the tip wrapped with protective tape, release the vent hole connector lock.
Disconnect the vent hole connector from the instrument panel passenger airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
| *a | Protective Tape |
| *b | Airbag Connector |
| *c | Airbag Connector Lock |
Using a screwdriver with the tip wrapped with protective tape, release the 2 airbag connector locks.
Disconnect the 2 airbag connectors to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.