Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL › from 2017.06
RM2170E _58 Vehicle Interior _057044 INTERIOR PANELS / TRIM _0278145 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

Click hereVehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55405B 4.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B484393C01
1.375,2.646 2.042,3.063 2.042,3.063 2.229,2.292 false 1.698,2.552 2.042,3.063 2.042,3.063 2.063,2.458 false 2.01,3.115 2.323,3.271 0.313,0.156 10 true *a
*a Clip A


Disengage the 13 clips.

NOTICE:

To prevent the center instrument cluster finish panel sub-assembly from being damaged, disengage the 4 clips (A), shown in the illustration, last.



b.

Disconnect the connector to remove the center instrument cluster finish panel sub-assembly.


Hide 55660 5.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)

a.
B482298

Disengage the 3 clips to remove the No. 2 instrument panel register assembly.


Hide 55650 6.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for RHD)

a.
B481620

Disengage the 3 clips to remove the No. 1 instrument panel register assembly.


Hide 55474B 7.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B484394C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area shown in the illustration.


b.
B484395

Using a moulding remover, disengage the 11 clips and 16 guides to remove the instrument cluster finish panel garnish.


Hide 55670A 8.REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B484396

Disengage the 3 clips to remove the center instrument panel register assembly.


Hide 55404D 9.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B484397

Using a clip remover, remove the 2 clips.


b.
B484398

Disengage the 4 claws and 9 guides to remove the instrument cluster finish panel sub-assembly.


Hide 83100 10.REMOVE COMBINATION METER ASSEMBLY

Hide 62312B 11.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Disconnect the front door opening trim weatherstrip LH.


Hide 62212 12.REMOVE FRONT PILLAR GARNISH LH

Hide 62311B 13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.

Disconnect the front door opening trim weatherstrip RH.


Hide 62211 14.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 82142A 15.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)

Hide 82142A 16.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)

Hide 17.REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

a.

Remove the bolt <A>.

B484400C01
6.656,2.052 6.969,2.208 0.313,0.156 10 true *a 3.563,1.229 3.875,1.385 0.313,0.156 10 true *b
*a Bolt <A> *b Screw <C>



b.

Remove the screw <C>.


c.

Using a clip remover, remove the 2 clips.


d.

Pull the upper instrument panel assembly in the direction indicated by the arrow (1) to disengage the 7 clips.

B484401N01
4.063,1.979 4.219,2.177 0.156,0.198 10 true 1 5.146,1.781 5.302,1.979 0.156,0.198 10 true 2


e.

Pull the upper instrument panel assembly in the direction indicated by the arrow (2) to disengage the 5 guides and remove the upper instrument panel assembly.