Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Parking Brake Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the parking brake switch assembly.

WIRING DIAGRAM

E333938E03
1.094,1.073 3.167,1.333 2.073,0.26 10 false Parking Brake Switch Assembly 1.094,0.906 1.51,1.125 0.417,0.219 10 false G24 4.094,1.073 5.74,1.531 1.646,0.458 10 false Instrument Panel Junction Block Assembly 3.781,0.531 4.198,0.75 0.417,0.219 10 false 28 3.781,0.729 4.146,0.938 0.365,0.208 10 false 3A 5.729,0.615 6,0.833 0.271,0.219 10 false 12 5.979,0.719 6.375,0.927 0.396,0.208 10 false PKB 2.406,0.615 2.823,0.833 0.417,0.219 10 false 1 5.427,1.885 5.823,2.094 0.396,0.208 10 false MB 5.427,2.063 7.104,2.542 1.677,0.479 10 false Main Body ECU (Multiplex Network Body ECU)

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch signal OFF or ON OFF: Parking brake switch off
ON: Parking brake switch on
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the parking brake switch assembly.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL


b.

Inspect the parking brake switch assembly.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G24-1 - 3A-28 Always Below 1 Ω
G24-1 or 3A-28 - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E259586C48
1.156,0.229 1.458,0.448 0.302,0.219 4.729,0.25 5.042,0.479 0.313,0.229 4.615,1.406 4.406,1.042 false 1.219,0.26 1.531,0.458 0.313,0.198 10 false 3A 4.771,0.281 5.083,0.479 0.313,0.198 10 false MB 4.49,1.448 5.031,1.688 0.542,0.24 10 false PKB 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 - MB-12 (PKB) Always Below 1 Ω
3A-28 or MB-12 (PKB) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY