Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SRS SEAT CUSHION AIRBAG ASSEMBLY(w/ Occupant Classification System) › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0321628 SRS SEAT CUSHION AIRBAG ASSEMBLY(w/ Occupant Classification System) N

SUPPLEMENTAL RESTRAINT SYSTEMS  SRS SEAT CUSHION AIRBAG ASSEMBLY(w/ Occupant Classification System)  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a front seat airbag sub-assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the front seat airbag sub-assembly.

·

The front seat airbag sub-assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat airbag sub-assembly with a deployed airbag.

·

Do not apply water etc. to a front seat airbag sub-assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the front seat airbag sub-assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 73906 2.DISPOSE OF FRONT SEAT AIRBAG SUB-ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the front seat airbag sub-assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a 12 V battery as the power source to deploy the airbag.


a.
C110371E49
0.969,1.24 0.708,0.729 0.708,0.729 0.458,0.729 false 0.146,0.656 0.521,0.854 0.375,0.198 10 false SST

Check the function of SST (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL).

SST
09082-00700  



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



d.

Disconnect the connector from the front seat airbag sub-assembly under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Slide the slider to release the lock, and then disconnect the yellow airbag connector as shown in the illustration.

C190412E07
1.856,2.092 2.072,2.245 0.216,0.154 10 *a 1.945,0.885 1.945,2.066 false 3.631,0.871 3.631,2.08 false 3.528,2.092 3.744,2.245 0.216,0.154 10 *a

Text in Illustration
*a Slider - -



e.

Install SST.

CAUTION:

Check that there is no looseness in the front seat assembly.


i.
B300233E01
0.147,1.118 0.455,1.266 0.309,0.148 10 SST 1.106,1.468 1.106,1.179 1.106,1.179 0.561,1.179 false 0.765,1.471 0.765,1.179 false

Connect the SST connector to the front seat airbag sub-assembly connector.

SST
09082-00700  
09082-00750  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
C154370E18
1.633,1.784 1.813,1.938 0.181,0.154 10 *a 0.211,1.051 0.514,1.204 0.303,0.154 10 SST 2.496,0.012 2.718,0.165 0.222,0.154 10 *1 0.965,1.384 0.72,1.14 0.72,1.14 0.567,1.14 false 1.778,0.537 2.242,0.073 2.242,0.073 2.467,0.073 false

Move SST at least 10 m (32.8 ft.) away from the front side window.

Text in Illustration
*1 12 V Battery
*a 10 m (32.8 ft.) or more


iii.

Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



f.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch to deploy the airbag.

CAUTION:
·

Before deployment, make sure that no one is near the vehicle.

·

The front seat airbag sub-assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat airbag sub-assembly with a deployed airbag.

·

Do not apply water etc. to a front seat airbag sub-assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




Hide 73906 3.DISPOSE OF FRONT SEAT AIRBAG SUB-ASSEMBLY (When Not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a 12 V battery as the power source to deploy the airbag.


a.
C110371E49
0.969,1.24 0.708,0.729 0.708,0.729 0.458,0.729 false 0.146,0.656 0.521,0.854 0.375,0.198 10 false SST

Check the function of SST (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL).

SST
09082-00700  


b.

Remove the front seat airbag sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SRS SEAT CUSHION AIRBAG ASSEMBLY(w/ Occupant Classification System)>REMOVAL).

CAUTION:
·

Before removing the front seat assembly, wait at least 90 seconds after turning the power switch off and disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When storing the front seat airbag sub-assembly, keep the airbag deployment side facing upward.




c.
B443970E01
2.281,0.948 2.708,0.49 2.708,0.49 2.51,0.49 false 2.281,0.396 2.594,0.594 0.313,0.198 10 false *1 2.656,1.5 2.969,1.698 0.313,0.198 10 false *a

Using braided wire, tie down the front seat airbag sub-assembly to an unneeded tire.

Text in Illustration
*1 Stripped Wire Section
*a Wire Diameter

Wire:

Stripped wire section

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire is too thin or an alternative object is used to tie down the front seat airbag sub-assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire section:

Area = 3.14 x (Diameter)2 / 4


i.
B288390

Install the 2 nuts to the front seat airbag sub-assembly.


ii.
B288391

Wind the wires around the front seat airbag sub-assembly as shown in the illustration.


iii.
B288392E02
2.02,0.008 2.174,0.170 0.154,0.162 10 *a 0.593,0.992 0.747,1.154 0.154,0.162 10 *b

Position the front seat airbag sub-assembly inside the tire.

Text in Illustration
*a Width
*b Inner Diameter

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the front seat airbag sub-assembly may break loose when the airbag is deployed.

·

Face the front seat airbag sub-assembly deployment surface toward the inside the tire to evenly distribute the force of deployment.



NOTICE:

The tire may be damaged by the airbag deployment, so use an unneeded tire.




d.

Install SST.

i.
B288393E04
0.792,1.365 0.656,0.958 false 0.396,0.844 0.698,1.021 0.302,0.177 10 false SST

Connect the SST connector to the front seat airbag sub-assembly connector.

SST
09082-00750  



e.

Place the tires.

i.
B300265E01
2.631,1.512 2.797,1.712 0.166,0.201 10 *1 2.633,0.706 2.798,0.906 0.166,0.201 10 *1 1.662,0 1.828,0.150 0.166,0.150 10 *a 0.698,0.849 0.864,1.050 0.166,0.201 10 *b

Place at least 2 tires under the tire to which the front seat airbag sub-assembly is tied.

Text in Illustration
*1 Tires (2 or more)
*a Inner Diameter
*b Width

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


NOTICE:
·

The tires may be damaged by the airbag deployment, so use unneeded tires.

·

Do not place the SST connector under the tire because it could be damaged.




ii.

Place at least 2 tires onto the tire to which the front seat airbag sub-assembly is tied. The top tire should have a wheel installed.


iii.
C223306

Tie the tires together with the 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.




f.

Install SST.

i.
B288395E02
0.121,2.692 0.444,2.875 0.323,0.184 10 SST 1.328,2.646 1.550,2.797 0.222,0.151 10 *a 1.436,1.499 1.659,1.677 0.223,0.178 10 *2 1.134,0.302 1.345,0.472 0.211,0.170 10 *1 1.386,0.393 2.195,0.393 2.195,0.393 2.515,1.216 false 1.153,1.581 1.423,1.581 false 0.306,2.313 0.306,2.67 false

Connect the SST connector.

Text in Illustration
*1 Front Seat Airbag Sub-assembly
*2 12 V Battery
*a 10 m (32.8 ft.) or more

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.



g.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the front seat airbag sub-assembly is tied.


iii.

Press the SST activation switch to deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the front seat airbag sub-assembly.

CAUTION:
·

The front seat airbag sub-assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat airbag sub-assembly with a deployed airbag.

·

Do not apply water etc. to a front seat airbag sub-assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the front seat airbag sub-assembly from the tire.


ii.

Place the front seat airbag sub-assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.