Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0321828 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The passenger side buckle switch circuit consists of the occupant detection ECU and front seat inner belt assembly RH.

DTC B1771 is stored when a malfunction is detected in the passenger side buckle switch circuit.

DTC No. DTC Detection Condition Trouble Area
B1771
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the passenger side buckle switch circuit.

·

Passenger side buckle switch malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Front seat inner belt assembly RH (Passenger side buckle switch)

·

Occupant detection ECU



WIRING DIAGRAM

C379005E03
1.385,0.76 2,1.094 0.615,0.333 10 false RBE+ 1.406,1.656 2.021,1.99 0.615,0.333 10 false RBE- 1.844,0.667 2.458,1 0.615,0.333 10 false 1 0.542,2.365 2.063,2.927 1.521,0.563 10 false O3 1.844,1.552 2.458,1.885 0.615,0.333 10 false 2 5.396,0.76 6.01,1.094 0.615,0.333 10 false BSW 5.396,1.656 6.01,1.99 0.615,0.333 10 false BGND 5.208,0.667 5.823,1 0.615,0.333 10 false 8 5.208,1.552 5.823,1.885 0.615,0.333 10 false 5 5.333,2.354 5.948,2.688 0.615,0.333 10 false O2 5.333,2.521 6.99,2.948 1.656,0.427 10 false Occupant Detection ECU 0.542,2.542 2.719,3.229 2.177,0.688 10 false Front Seat Inner Belt Assembly RH (Passenger Side Buckle Switch)

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1771 is output, perform troubleshooting for this DTC first.

·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)

NG

REPLACE FRONT SEAT WIRE RH

2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)
a.
C238370C06
0.875,2.354 1.219,2.573 0.344,0.219 1.635,0.656 1.635,0.219 1.635,0.219 1.823,0.219 false 2.167,2.427 2.51,2.427 false 1.948,2.531 1.948,2.875 false 2.552,2.344 3.031,2.625 0.479,0.281 10 false BGND 1.781,2.906 2.208,3.115 0.427,0.208 10 false BSW 0.969,2.385 1.365,2.667 0.396,0.281 10 false O2 0.99,0.625 1.385,0.938 0.396,0.313 10 false D 1.271,0.625 1.625,0.917 0.354,0.292 10 false C 1.885,0.635 2.167,1 0.281,0.365 10 false B 2.167,0.635 2.438,0.979 0.271,0.344 10 false A 2.479,0.792 2.792,1.063 0.313,0.271 10 false *2 0.729,1.781 1.083,2.104 0.354,0.323 10 false *a 0.688,0.625 1.083,0.885 0.396,0.26 10 false *1 1.865,0.135 2.135,0.406 0.271,0.271 10 false *3
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O2-8 (BSW) - Body ground Power switch on (IG) Below 1 V
O2-5 (BGND) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

3.CHECK FRONT SEAT WIRE RH (OPEN)

NG

REPLACE FRONT SEAT WIRE RH

3.CHECK FRONT SEAT WIRE RH (OPEN)
a.
B483195C02
0.938,0.646 1.281,0.896 0.344,0.25 0.802,3.427 1.146,3.677 0.344,0.25 1.594,2.573 1.594,2.156 false 1.531,4.135 1.031,4.135 false 1.719,3.552 1.396,3.177 false 2.073,3.552 2.385,3.177 false 1.708,1.26 2.031,0.833 false 2.688,1.271 2.281,0.708 false 0.667,2 1.323,2.542 0.656,0.542 10 false *1 2.448,2.167 2.833,2.792 0.385,0.625 10 false *2 1.531,2.583 1.917,2.833 0.385,0.25 10 false *3 0.875,4.052 1.281,4.375 0.406,0.323 10 false *4 0.813,0.188 1.25,0.615 0.438,0.427 10 false *a 0.5,3.01 0.885,3.542 0.385,0.531 10 false *b 2.135,2.01 2.792,2.552 0.656,0.542 10 false A 1.865,2.01 2.521,2.552 0.656,0.542 10 false B 1.24,2.01 1.896,2.552 0.656,0.542 10 false C 0.958,2.01 1.615,2.552 0.656,0.542 10 false D 1.031,0.688 1.438,0.99 0.406,0.302 10 false O2 0.885,3.469 1.292,3.771 0.406,0.302 10 false O3 1.031,3.094 1.49,3.396 0.458,0.302 10 false RBE- 2.427,3.094 2.885,3.396 0.458,0.302 10 false RBE+ 1.552,1.281 2.01,1.583 0.458,0.302 10 false BSW 2.5,1.281 2.958,1.583 0.458,0.302 10 false BGND
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Using a service wire, connect terminals 1 (RBE+) and 2 (RBE-) of connector C as shown in the illustration.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-8 (BSW) - O2-5 (BGND) Always Below 1 Ω



c.

Disconnect the service wire from connector C.



OK

4.CHECK FRONT SEAT WIRE RH (SHORT)

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH (SHORT)
a.
C238370C06
0.875,2.354 1.219,2.573 0.344,0.219 1.635,0.656 1.635,0.219 1.635,0.219 1.823,0.219 false 2.167,2.427 2.51,2.427 false 1.948,2.531 1.948,2.875 false 2.552,2.344 3.031,2.625 0.479,0.281 10 false BGND 1.781,2.906 2.208,3.115 0.427,0.208 10 false BSW 0.969,2.385 1.365,2.667 0.396,0.281 10 false O2 0.99,0.625 1.385,0.938 0.396,0.313 10 false D 1.271,0.625 1.625,0.917 0.354,0.292 10 false C 1.885,0.635 2.167,1 0.281,0.365 10 false B 2.167,0.635 2.438,0.979 0.271,0.344 10 false A 2.479,0.792 2.792,1.063 0.313,0.271 10 false *2 0.729,1.781 1.083,2.104 0.354,0.323 10 false *a 0.688,0.625 1.083,0.885 0.396,0.26 10 false *1 1.865,0.135 2.135,0.406 0.271,0.271 10 false *3
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-8 (BSW) - O2-5 (BGND) Always 1 MΩ or higher




OK

5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)
a.
C238370C06
0.875,2.354 1.219,2.573 0.344,0.219 1.635,0.656 1.635,0.219 1.635,0.219 1.823,0.219 false 2.167,2.427 2.51,2.427 false 1.948,2.531 1.948,2.875 false 2.552,2.344 3.031,2.625 0.479,0.281 10 false BGND 1.781,2.906 2.208,3.115 0.427,0.208 10 false BSW 0.969,2.385 1.365,2.667 0.396,0.281 10 false O2 0.99,0.625 1.385,0.938 0.396,0.313 10 false D 1.271,0.625 1.625,0.917 0.354,0.292 10 false C 1.885,0.635 2.167,1 0.281,0.365 10 false B 2.167,0.635 2.438,0.979 0.271,0.344 10 false A 2.479,0.792 2.792,1.063 0.313,0.271 10 false *2 0.729,1.781 1.083,2.104 0.354,0.323 10 false *a 0.688,0.625 1.083,0.885 0.396,0.26 10 false *1 1.865,0.135 2.135,0.406 0.271,0.271 10 false *3
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-8 (BSW) - Body ground Always 1 MΩ or higher
O2-5 (BGND) - Body ground Always 1 MΩ or higher




OK

6.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

6.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


d.

Clear the DTCs stored in the airbag sensor assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).


e.

Turn the power switch off.


f.

Turn the power switch on (IG).


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.



OK

NG

7.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
7.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the front seat inner belt assembly RH with a known good one (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


e.

Clear the DTCs stored in the airbag sensor assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).


f.

Turn the power switch off.


g.

Turn the power switch on (IG).


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Return the front seat inner belt assembly RH that was installed for testing to its original location (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG

8.REPLACE OCCUPANT DETECTION ECU
8.REPLACE OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.



c.

Connect the cable to the negative (-) auxiliary battery terminal.



NEXT

9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

END