Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0321828 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1790  Center Airbag Sensor Assembly Communication Circuit Malfunction  


DESCRIPTION

The airbag sensor assembly communication circuit consists of the occupant detection ECU and airbag sensor assembly.

DTC B1790 is stored when a malfunction is detected in the airbag sensor assembly communication circuit.

DTC No. DTC Detection Condition Trouble Area
B1790
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the airbag sensor assembly communication circuit.

·

Occupant detection ECU malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat wire RH

·

Occupant detection ECU

·

Airbag sensor assembly



HINT:

When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1790 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM

C238367E49
0.573,3.083 2.417,3.417 1.844,0.333 10 false Occupant Detection ECU 0.573,2.917 1.292,3.354 0.719,0.438 10 false O2 3.406,0.906 3.896,1.49 0.49,0.583 10 false MO1 3.51,0.698 3.948,1.396 0.438,0.698 10 false 1 3.51,1.885 4.021,2.667 0.51,0.781 10 false 5 3.406,2.083 3.875,2.542 0.469,0.458 10 false MO1 5.135,0.802 5.667,1.281 0.531,0.479 10 false 16 5.146,1.958 5.542,2.313 0.396,0.354 10 false 24 5.354,2.917 5.948,3.281 0.594,0.365 10 false M58 5.354,3.094 7.104,3.417 1.75,0.323 10 false Airbag Sensor Assembly 1.396,0.906 2.448,1.531 1.052,0.625 10 false FSR+ 1.427,2.073 2.115,2.385 0.688,0.313 10 false FSR- 5.385,0.917 5.969,1.354 0.583,0.438 10 false FSR+ 5.385,2.083 6.01,2.542 0.625,0.458 10 false FSR- 1.854,0.781 2.281,1.458 0.427,0.677 10 false 7 1.854,1.969 2.24,2.396 0.385,0.427 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and occupant detection ECU. Also check that the connectors that link the front seat wire RH and floor wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and occupant detection ECU. Also disconnect the connectors that link the front seat wire RH and floor wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)

NG

REPLACE WIRE HARNESS

2.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)
a.
C238376C10
0.385,2.438 0.74,2.656 0.354,0.219 1.292,2.635 1.292,2.979 false 1.5,2.479 1.5,2.052 1.5,2.052 1.76,2.052 false 1.406,0.854 2.156,1.354 0.75,0.5 10 false D 1.063,0.854 1.646,1.385 0.583,0.531 10 false E 0.813,0.844 1.833,1.313 1.021,0.469 10 false F 1.563,0.854 2.042,1.323 0.479,0.469 10 false C 1.906,0.844 2.406,1.26 0.5,0.417 10 false B 2.146,0.854 2.583,1.24 0.438,0.385 10 false A 0.427,0.99 1.115,1.385 0.688,0.396 10 false *1 2.604,0.573 3.01,0.958 0.406,0.385 10 false *2 1.792,1.979 2.271,2.292 0.479,0.313 10 false FSR- 1.146,3 1.729,3.292 0.583,0.292 10 false FSR+ 0.479,2.469 0.885,2.823 0.406,0.354 10 false O2 0.302,1.885 0.927,2.313 0.625,0.427 10 false *a
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Occupant Detection ECU)


Connect the connectors that link the floor wire and front seat wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O2-7 (FSR+) - Body ground Power switch on (IG) Below 1 V
O2-4 (FSR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)

NG

10.CHECK FLOOR WIRE (SHORT TO B+)
3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)
a.
C238377C08
0.677,3.781 1,4.01 0.323,0.229 0.333,0.604 0.698,0.854 0.365,0.25 1.948,0.844 2.198,0.844 false 1.646,0.729 1.99,0.479 false 1.646,0.948 1.99,1.167 false 1.531,3.958 1.531,4.365 false 1.74,3.792 1.74,3.375 1.74,3.375 2,3.375 false 1.406,2.406 1.792,2.76 0.385,0.354 10 false D 1.063,2.406 1.396,2.771 0.333,0.365 10 false E 0.823,2.406 1.25,2.74 0.427,0.333 10 false F 1.563,2.406 1.979,2.792 0.417,0.385 10 false C 1.906,2.406 2.208,2.823 0.302,0.417 10 false B 2.146,2.406 2.458,2.792 0.313,0.385 10 false A 0.427,2.563 0.781,2.875 0.354,0.313 10 false *1 2.635,2.104 2.948,2.406 0.313,0.302 10 false *2 2.021,0.396 2.458,0.635 0.438,0.24 10 false FSR+ 2.031,1.104 2.542,1.438 0.51,0.333 10 false FSR- 0.271,0.156 0.552,0.438 0.281,0.281 10 false *a 2.042,3.302 2.448,3.594 0.406,0.292 10 false FSR- 1.385,4.385 1.844,4.625 0.458,0.24 10 false FSR+ 0.76,3.813 1.104,4.073 0.344,0.26 10 false O2 0.385,0.646 0.813,1.042 0.427,0.396 10 false M58 0.583,3.281 0.958,3.583 0.375,0.302 10 false *b 2.229,0.76 2.479,1.021 0.25,0.26 10 false *3
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Occupant Detection ECU)


Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-7 (FSR+) - O2-4 (FSR-) Always Below 1 Ω




OK

4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)

NG

11.CHECK FLOOR WIRE (OPEN)
4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)
a.
C238376C10
0.385,2.438 0.74,2.656 0.354,0.219 1.292,2.635 1.292,2.979 false 1.5,2.479 1.5,2.052 1.5,2.052 1.76,2.052 false 1.406,0.854 2.156,1.354 0.75,0.5 10 false D 1.063,0.854 1.646,1.385 0.583,0.531 10 false E 0.813,0.844 1.833,1.313 1.021,0.469 10 false F 1.563,0.854 2.042,1.323 0.479,0.469 10 false C 1.906,0.844 2.406,1.26 0.5,0.417 10 false B 2.146,0.854 2.583,1.24 0.438,0.385 10 false A 0.427,0.99 1.115,1.385 0.688,0.396 10 false *1 2.604,0.573 3.01,0.958 0.406,0.385 10 false *2 1.792,1.979 2.271,2.292 0.479,0.313 10 false FSR- 1.146,3 1.729,3.292 0.583,0.292 10 false FSR+ 0.479,2.469 0.885,2.823 0.406,0.354 10 false O2 0.302,1.885 0.927,2.313 0.625,0.427 10 false *a
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Occupant Detection ECU)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-7 (FSR+) - O2-4 (FSR-) Always 1 MΩ or higher




OK

5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)

NG

12.CHECK FLOOR WIRE (SHORT)
5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)
a.
C238376C10
0.385,2.438 0.74,2.656 0.354,0.219 1.292,2.635 1.292,2.979 false 1.5,2.479 1.5,2.052 1.5,2.052 1.76,2.052 false 1.406,0.854 2.156,1.354 0.75,0.5 10 false D 1.063,0.854 1.646,1.385 0.583,0.531 10 false E 0.813,0.844 1.833,1.313 1.021,0.469 10 false F 1.563,0.854 2.042,1.323 0.479,0.469 10 false C 1.906,0.844 2.406,1.26 0.5,0.417 10 false B 2.146,0.854 2.583,1.24 0.438,0.385 10 false A 0.427,0.99 1.115,1.385 0.688,0.396 10 false *1 2.604,0.573 3.01,0.958 0.406,0.385 10 false *2 1.792,1.979 2.271,2.292 0.479,0.313 10 false FSR- 1.146,3 1.729,3.292 0.583,0.292 10 false FSR+ 0.479,2.469 0.885,2.823 0.406,0.354 10 false O2 0.302,1.885 0.927,2.313 0.625,0.427 10 false *a
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-7 (FSR+) - Body ground Always 1 MΩ or higher
O2-4 (FSR-) - Body ground Always 1 MΩ or higher




OK

6.CHECK DTC

NG

13.CHECK FLOOR WIRE (SHORT TO GROUND)
6.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


d.

Clear the DTCs stored in the airbag sensor assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).


e.

Turn the power switch off.


f.

Turn the power switch on (IG).


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

Codes other than DTC B1790 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.



OK

NG

7.CHECK OCCUPANT DETECTION ECU
7.CHECK OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the occupant detection ECU with a known good one (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU(w/ Occupant Classification System)>REMOVAL).

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


e.

Clear the DTCs stored in the airbag sensor assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).


f.

Turn the power switch off.


g.

Turn the power switch on (IG).


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1790 is not output.


HINT:

Codes other than DTC B1790 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Return the occupant detection ECU that was installed for testing to its original location (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU(w/ Occupant Classification System)>REMOVAL).



OK

8.REPLACE OCCUPANT DETECTION ECU

NG

8.REPLACE OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.



c.

Connect the cable to the negative (-) auxiliary battery terminal.



NEXT

9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

END

10.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238378C08
0.5,2.458 0.885,2.708 0.385,0.25 1.354,2.677 1.354,3.031 false 1.354,2.542 1.354,2.073 1.354,2.073 1.5,2.073 false 1.26,1.01 1.26,1.313 false 1.792,0.875 1.792,0.438 1.792,0.438 1.594,0.438 false 1.375,0.854 1.802,1.229 0.427,0.375 10 false D 1.063,0.865 1.5,1.302 0.438,0.438 10 false E 0.813,0.854 1.354,1.323 0.542,0.469 10 false F 1.594,0.854 2.115,1.365 0.521,0.51 10 false C 1.906,0.854 2.26,1.354 0.354,0.5 10 false B 2.146,0.854 2.583,1.479 0.438,0.625 10 false A 0.406,0.99 0.906,1.302 0.5,0.313 10 false *1 2.604,0.573 2.99,1 0.385,0.427 10 false *2 1.208,3.042 1.781,3.26 0.573,0.219 10 false FSR- 1.531,2 2.031,2.292 0.5,0.292 10 false FSR+ 0.552,2.5 0.948,2.802 0.396,0.302 10 false MO1 0.292,1.979 0.656,2.323 0.365,0.344 10 false *a 1.188,1.323 1.51,1.604 0.323,0.281 10 false *3 1.417,0.354 1.719,0.625 0.302,0.271 10 false *4
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the front seat wire RH connector from the floor wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MO1-1 (FSR+) - Body ground Power switch on (IG) Below 1 V
MO1-5 (FSR-) - Body ground Power switch on (IG) Below 1 V




OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

11.CHECK FLOOR WIRE (OPEN)
a.
C238379C07
0.583,3.781 0.958,4.01 0.375,0.229 0.313,0.604 0.656,0.844 0.344,0.24 1.948,0.833 2.24,0.833 false 1.615,0.708 1.958,0.51 false 1.625,0.948 1.969,1.146 false 1.365,3.979 1.365,4.323 false 1.375,3.844 1.375,3.385 1.375,3.385 1.51,3.385 false 1.281,2.583 1.281,2.833 false 1.813,2.448 1.813,2.115 1.813,2.115 1.594,2.115 false 1.396,2.438 1.833,2.823 0.438,0.385 10 false D 1.083,2.438 1.552,2.813 0.469,0.375 10 false E 0.844,2.438 1.083,2.74 0.24,0.302 10 false F 1.615,2.438 1.938,2.76 0.323,0.323 10 false C 1.927,2.438 2.24,2.854 0.313,0.417 10 false B 2.177,2.438 2.448,2.729 0.271,0.292 10 false A 0.448,2.573 1.042,3.031 0.594,0.458 10 false *1 2.656,2.135 3,2.594 0.344,0.458 10 false *2 2.01,0.417 2.49,0.667 0.479,0.25 10 false FSR+ 2.01,1.073 2.479,1.375 0.469,0.302 10 false FSR- 0.26,0.156 0.563,0.438 0.302,0.281 10 false *a 1.552,3.313 1.969,3.667 0.417,0.354 10 false FSR+ 0.635,3.813 1.063,4.146 0.427,0.333 10 false MO1 0.354,0.646 0.844,1.01 0.49,0.365 10 false M58 0.49,3.281 0.958,3.563 0.469,0.281 10 false *b 1.24,4.354 1.688,4.667 0.448,0.313 10 false FSR- 1.208,2.854 1.531,3.24 0.323,0.385 10 false *3 1.438,2.031 1.906,2.375 0.469,0.344 10 false *4 2.271,0.76 2.604,1.031 0.333,0.271 10 false *5
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the front seat wire RH connector from the floor wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MO1-1 (FSR+) - MO1-5 (FSR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

12.CHECK FLOOR WIRE (SHORT)
a.
C238378C08
0.5,2.458 0.885,2.708 0.385,0.25 1.354,2.677 1.354,3.031 false 1.354,2.542 1.354,2.073 1.354,2.073 1.5,2.073 false 1.26,1.01 1.26,1.313 false 1.792,0.875 1.792,0.438 1.792,0.438 1.594,0.438 false 1.375,0.854 1.802,1.229 0.427,0.375 10 false D 1.063,0.865 1.5,1.302 0.438,0.438 10 false E 0.813,0.854 1.354,1.323 0.542,0.469 10 false F 1.594,0.854 2.115,1.365 0.521,0.51 10 false C 1.906,0.854 2.26,1.354 0.354,0.5 10 false B 2.146,0.854 2.583,1.479 0.438,0.625 10 false A 0.406,0.99 0.906,1.302 0.5,0.313 10 false *1 2.604,0.573 2.99,1 0.385,0.427 10 false *2 1.208,3.042 1.781,3.26 0.573,0.219 10 false FSR- 1.531,2 2.031,2.292 0.5,0.292 10 false FSR+ 0.552,2.5 0.948,2.802 0.396,0.302 10 false MO1 0.292,1.979 0.656,2.323 0.365,0.344 10 false *a 1.188,1.323 1.51,1.604 0.323,0.281 10 false *3 1.417,0.354 1.719,0.625 0.302,0.271 10 false *4
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the front seat wire RH connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MO1-1 (FSR+) - MO1-5 (FSR-) Always 1 MΩ or higher




OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

13.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238378C08
0.5,2.458 0.885,2.708 0.385,0.25 1.354,2.677 1.354,3.031 false 1.354,2.542 1.354,2.073 1.354,2.073 1.5,2.073 false 1.26,1.01 1.26,1.313 false 1.792,0.875 1.792,0.438 1.792,0.438 1.594,0.438 false 1.375,0.854 1.802,1.229 0.427,0.375 10 false D 1.063,0.865 1.5,1.302 0.438,0.438 10 false E 0.813,0.854 1.354,1.323 0.542,0.469 10 false F 1.594,0.854 2.115,1.365 0.521,0.51 10 false C 1.906,0.854 2.26,1.354 0.354,0.5 10 false B 2.146,0.854 2.583,1.479 0.438,0.625 10 false A 0.406,0.99 0.906,1.302 0.5,0.313 10 false *1 2.604,0.573 2.99,1 0.385,0.427 10 false *2 1.208,3.042 1.781,3.26 0.573,0.219 10 false FSR- 1.531,2 2.031,2.292 0.5,0.292 10 false FSR+ 0.552,2.5 0.948,2.802 0.396,0.302 10 false MO1 0.292,1.979 0.656,2.323 0.365,0.344 10 false *a 1.188,1.323 1.51,1.604 0.323,0.281 10 false *3 1.417,0.354 1.719,0.625 0.302,0.271 10 false *4
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the front seat wire RH connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MO1-1 (FSR+) - Body ground Always 1 MΩ or higher
MO1-5 (FSR-) - Body ground Always 1 MΩ or higher




OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE