The front passenger side squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1805/52 | ·
The airbag sensor assembly detects a line short in the front passenger side squib circuit during the primary check. ·
Front passenger side squib malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib) ·
Airbag sensor assembly |
| B1806/52 | ·
The airbag sensor assembly detects an open in the front passenger side squib circuit. ·
Front passenger side squib malfunction ·
Airbag sensor assembly malfunction |
|
| B1807/52 | ·
The airbag sensor assembly detects a short to ground in the front passenger side squib circuit. ·
Front passenger side squib malfunction ·
Airbag sensor assembly malfunction |
|
| B1808/52 | ·
The airbag sensor assembly detects a short to B+ in the front passenger side squib circuit. ·
Front passenger side squib malfunction ·
Airbag sensor assembly malfunction |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
| *A | w/o Occupant Classification System |
| *B | w/ Occupant Classification System |
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Instrument Panel Wire |
| *4 | Instrument Panel Wire |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag sensor assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the instrument panel passenger airbag assembly and airbag sensor assembly. Also disconnect the connectors that link the instrument panel wire and No. 2 instrument panel wire.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and No. 2 instrument panel wire connector are not deformed or damaged.
The short springs are not deformed or damaged.
OK
NG
Connect the instrument panel wire to the No. 2 instrument panel wire and airbag sensor assembly.
| *A | w/o Occupant Classification System | *B | w/ Occupant Classification System |
| *1 | Instrument Panel Passenger Airbag Assembly | *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly) |
*b | Color: Orange |
Connect SST (resistance 2.1 Ω) to connector E (orange connector).
Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.
Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Disconnect SST from connector E.
OK
NG
Disconnect the instrument panel wire from the airbag sensor assembly.
| *A | w/o Occupant Classification System | *B | w/ Occupant Classification System |
| *1 | Instrument Panel Passenger Airbag Assembly | *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly) |
*b | Color: Orange |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (P+) - Body ground | Power switch on (IG) | Below 1 V |
| F1-1 (P-) - Body ground | Power switch on (IG) | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-2 (P+) - Body ground | Power switch on (IG) | Below 1 V |
| F2-1 (P-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (P+) - F1-1 (P-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-2 (P+) - F2-1 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (P+) - Body ground | Always | 1 MΩ or higher |
| F1-1 (P-) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-2 (P+) - Body ground | Always | 1 MΩ or higher |
| F2-1 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (P+) - F1-1 (P-) | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-2 (P+) - F2-1 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
OK
NG
| *A | w/o Occupant Classification System |
| *B | w/ Occupant Classification System |
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.
Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.
OK
(See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the No. 2 instrument panel wire from the instrument panel wire.
| *A | w/o Occupant Classification System | *B | w/ Occupant Classification System |
| *1 | Instrument Panel Passenger Airbag Assembly | *2 | Airbag Sensor Assembly |
| *3 | No. 2 Instrument Panel Wire | *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to No. 2 Instrument Panel Wire) |
- | - |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GF1-1 (P+) - Body ground | Power switch on (IG) | Below 1 V |
| GF1-2 (P-) - Body ground | Power switch on (IG) | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GF2-1 (P+) - Body ground | Power switch on (IG) | Below 1 V |
| GF2-2 (P-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GF1-1 (P+) - GF1-2 (P-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GF2-1 (P+) - GF2-2 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GF1-1 (P+) - Body ground | Always | 1 MΩ or higher |
| GF1-2 (P-) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GF2-1 (P+) - Body ground | Always | 1 MΩ or higher |
| GF2-2 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GF1-1 (P+) - GF1-2 (P-) | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GF2-1 (P+) - GF2-2 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
OK
NG
Check for a short to B+ in the circuit.
| *A | w/o Occupant Classification System | *B | w/ Occupant Classification System |
| *1 | Instrument Panel Passenger Airbag Assembly | *2 | Airbag Sensor Assembly |
| *3 | No. 2 Instrument Panel Wire | *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly) |
*b | Color: Orange |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (P+) - Body ground | Power switch on (IG) | Below 1 V |
| F1-1 (P-) - Body ground | Power switch on (IG) | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-2 (P+) - Body ground | Power switch on (IG) | Below 1 V |
| F2-1 (P-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (P+) - F1-1 (P-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-2 (P+) - F2-1 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (P+) - Body ground | Always | 1 MΩ or higher |
| F1-1 (P-) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-2 (P+) - Body ground | Always | 1 MΩ or higher |
| F2-1 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (P+) - F1-1 (P-) | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-2 (P+) - F2-1 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
OK
(See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG