Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B181A/7A  Short in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181B/7A  Open in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181C/7A  Short to GND in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181D/7A  Short to B+ in Passenger Side Airbag Variable Vent Hole Squib Circuit  


DESCRIPTION

The passenger side airbag variable vent hole squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the passenger side airbag variable vent hole squib circuit.

DTC No. DTC Detection Condition Trouble Area
B181A/7A
·

The airbag sensor assembly detects a line short in the passenger side airbag variable vent hole squib circuit during the primary check.

·

Passenger side airbag variable vent hole squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Passenger side airbag variable vent hole squib)

·

Airbag sensor assembly


B181B/7A
·

The airbag sensor assembly detects an open in the passenger side airbag variable vent hole squib circuit.

·

Passenger side airbag variable vent hole squib malfunction

·

Airbag sensor assembly malfunction


B181C/7A
·

The airbag sensor assembly detects a short to ground in the passenger side airbag variable vent hole squib circuit.

·

Passenger side airbag variable vent hole squib malfunction

·

Airbag sensor assembly malfunction


B181D/7A
·

The airbag sensor assembly detects a short to B+ in the passenger side airbag variable vent hole squib circuit.

·

Passenger side airbag variable vent hole squib malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C351803E21
0.708,2.51 1.5,2.896 0.792,0.385 10 false F4 0.708,2.656 3.792,3.188 3.083,0.531 10 false Instrument Panel Passenger Airbag Assembly (Passenger Side Airbag Variable Vent Hole Squib) 1.979,1.896 2.771,2.281 0.792,0.385 10 false VHP- 1.948,1.063 2.74,1.448 0.792,0.385 10 false VHP+ 2.406,1.063 3.198,1.448 0.792,0.385 10 false 2 2.406,1.896 3.198,2.281 0.792,0.385 10 false 1 3.365,1.167 4.156,1.552 0.792,0.385 10 false GF1 4.448,1.073 5.24,1.458 0.792,0.385 10 false 19 4.448,1.906 5.24,2.292 0.792,0.385 10 false 20 4.677,3.188 6.479,3.615 1.802,0.427 10 false Airbag Sensor Assembly 4.677,3.021 5.469,3.406 0.792,0.385 10 false G18 3.375,2.01 4.167,2.396 0.792,0.385 10 false GF1 4.698,1.177 5.49,1.563 0.792,0.385 10 false VHP+ 4.698,2.01 5.49,2.396 0.792,0.385 10 false VHP- 3.469,0.969 4.26,1.354 0.792,0.385 10 false 1 3.479,1.813 4.271,2.198 0.792,0.385 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C238337C01
0.281,1.115 0.281,1.542 false 1.76,1.115 1.76,1.542 false 0.979,0.979 0.979,0.604 0.979,0.604 0.823,0.604 false 0.219,1.563 0.563,1.781 0.344,0.219 10 *1 0.646,0.521 1.021,0.771 0.375,0.25 10 *3 2.708,0.958 3.042,1.302 0.333,0.344 10 *2 2.26,0.958 2.573,1.323 0.313,0.365 10 A 1.948,0.958 2.198,1.448 0.25,0.49 10 B 1.479,0.969 1.688,1.188 0.208,0.219 10 C 1.167,0.969 1.469,1.229 0.302,0.26 10 D 0.698,0.969 0.896,1.177 0.198,0.208 10 E 0.396,0.969 0.677,1.198 0.281,0.229 10 F 1.698,1.563 2.031,1.844 0.333,0.281 10 *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag sensor assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the instrument panel passenger airbag assembly and airbag sensor assembly. Also disconnect the connectors that link the instrument panel wire and No. 2 instrument panel wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and No. 2 instrument panel wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.




OK

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (PASSENGER SIDE AIRBAG VARIABLE VENT HOLE SQUIB)

NG

REPLACE WIRE HARNESS

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (PASSENGER SIDE AIRBAG VARIABLE VENT HOLE SQUIB)
a.
B483637C02
0.448,2.01 0.771,2.25 0.323,0.24 0.417,1.188 0.417,0.813 false 2.031,2.833 1.646,2.635 false 2.188,2.188 1.885,2.188 false 0.354,1.198 0.896,1.573 0.542,0.375 10 false *1 2.667,0.677 3.333,1.115 0.667,0.438 10 false *2 0.271,1.604 0.635,1.958 0.365,0.354 10 false *a 2.219,2.115 2.677,2.542 0.458,0.427 10 false SST 2.208,0.677 2.875,1.115 0.667,0.438 10 false A 2.052,0.677 2.719,1.115 0.667,0.438 10 false B 1.563,0.677 2.229,1.115 0.667,0.438 10 false C 1.417,0.677 2.083,1.115 0.667,0.438 10 false D 0.927,0.677 1.594,1.115 0.667,0.438 10 false E 0.531,0.677 1.198,1.115 0.667,0.438 10 false F 0.531,2.052 0.896,2.406 0.365,0.354 10 false F4 2.063,2.771 2.521,3.198 0.458,0.427 10 false *b
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Green


Connect the instrument panel wire to the No. 2 instrument panel wire and airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E (green connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (passenger side airbag variable vent hole squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output.


HINT:

Codes other than DTCs B181A/7A, B181B/7A, B181C/7A and B181D/7A may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

3.CHECK PASSENGER SIDE AIRBAG VARIABLE VENT HOLE SQUIB CIRCUIT
3.CHECK PASSENGER SIDE AIRBAG VARIABLE VENT HOLE SQUIB CIRCUIT
a.
B483638C02
0.698,2.167 1.063,2.417 0.365,0.25 0.448,1.188 0.448,0.833 false 1.375,1.823 1.656,2.063 false 2.104,1.833 1.781,2.063 false 2.25,2.635 1.917,2.458 false 0.385,1.208 0.885,1.708 0.5,0.5 10 false *1 2.656,0.677 3.083,1.052 0.427,0.375 10 false *2 0.292,1.719 0.823,2.281 0.531,0.563 10 false *a 2.271,2.563 2.698,2.948 0.427,0.385 10 false *b 2.26,0.677 2.688,1.052 0.427,0.375 10 false A 1.948,0.677 2.375,1.052 0.427,0.375 10 false B 1.5,0.677 1.927,1.052 0.427,0.375 10 false C 1.344,0.677 1.771,1.052 0.427,0.375 10 false D 0.896,0.677 1.323,1.052 0.427,0.375 10 false E 0.583,0.677 1.01,1.052 0.427,0.375 10 false F 0.802,2.208 1.333,2.771 0.531,0.563 10 false F4 1.01,1.76 1.615,2.271 0.604,0.51 10 false VHP- 2.156,1.76 2.76,2.271 0.604,0.51 10 false VHP+
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Green


Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F4-2 (VHP+) - Body ground Power switch on (IG) Below 1 V
F4-1 (VHP-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (VHP+) - F4-1 (VHP-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (VHP+) - Body ground Always 1 MΩ or higher
F4-1 (VHP-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (VHP+) - F4-1 (VHP-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238340C07
0.448,1.115 0.448,1.406 false 0.573,0.969 1.698,1.51 1.125,0.542 10 false F 0.719,0.969 1.323,1.552 0.604,0.583 10 false E 1.24,0.969 2.115,1.438 0.875,0.469 10 false D 1.396,0.969 1.896,1.458 0.5,0.49 10 false C 1.917,0.969 2.438,1.427 0.521,0.458 10 false B 2.073,0.969 2.458,1.344 0.385,0.375 10 false A 0.385,1.427 0.948,1.854 0.563,0.427 10 false *1 2.49,0.979 2.823,1.385 0.333,0.406 10 false *2
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly


Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output.


HINT:

Codes other than DTCs B181A/7A, B181B/7A, B181C/7A and B181D/7A may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.
B483639C02
0.802,2.208 1.188,2.458 0.385,0.25 0.302,1.125 0.302,0.792 false 1.021,1.094 1.021,0.76 false 1.781,0.667 1.781,0.25 1.781,0.25 1.615,0.25 false 1.302,2.948 1.667,2.615 false 2.177,2.938 1.833,2.615 false 0.24,1.125 0.646,1.479 0.406,0.354 10 false *1 2.677,0.635 3.052,1.188 0.375,0.552 10 false *2 0.948,1.094 1.417,1.49 0.469,0.396 10 false *3 1.469,0.177 1.906,0.5 0.438,0.323 10 false *4 0.375,1.781 0.875,2.198 0.5,0.417 10 false *a 0.865,2.25 1.365,2.667 0.5,0.417 10 false GF1 1.146,2.948 1.698,3.365 0.552,0.417 10 false VHP+ 2.052,2.948 2.604,3.365 0.552,0.417 10 false VHP- 2.271,0.635 2.646,1.188 0.375,0.552 10 false A 1.958,0.635 2.333,1.188 0.375,0.552 10 false B 1.51,0.635 1.885,1.188 0.375,0.552 10 false C 1.198,0.635 1.573,1.188 0.375,0.552 10 false D 0.75,0.635 1.125,1.188 0.375,0.552 10 false E 0.438,0.635 0.813,1.188 0.375,0.552 10 false F
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Disconnect the No. 2 instrument panel wire from the instrument panel wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
GF1-1 (VHP+) - Body ground Power switch on (IG) Below 1 V
GF1-2 (VHP-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GF1-1 (VHP+) - GF1-2 (VHP-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GF1-1 (VHP+) - Body ground Always 1 MΩ or higher
GF1-2 (VHP-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GF1-1 (VHP+) - GF1-2 (VHP-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.




OK

6.CHECK NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK NO. 2 INSTRUMENT PANEL WIRE
a.
B483640C02
0.667,2.323 1.01,2.563 0.344,0.24 1.198,1.927 1.479,2.135 false 0.313,0.792 0.313,1.125 false 0.833,0.25 1,0.25 1,0.25 1,0.667 false 1.781,0.76 1.781,1.094 false 1.906,1.938 1.615,2.135 false 2.052,2.656 1.74,2.531 false 0.25,1.135 0.667,1.479 0.417,0.344 10 false *1 2.708,0.635 3.156,1.083 0.448,0.448 10 false *2 0.688,0.177 1.229,0.594 0.542,0.417 10 false *3 1.719,1.104 2.208,1.635 0.49,0.531 10 false *4 0.354,1.833 0.813,2.26 0.458,0.427 10 false *a 2.073,2.583 2.594,2.938 0.521,0.354 10 false *b 0.813,1.854 1.333,2.208 0.521,0.354 10 false VHP- 1.958,1.854 2.479,2.208 0.521,0.354 10 false VHP+ 0.76,2.354 1.281,2.708 0.521,0.354 10 false F4 2.281,0.635 2.729,1.083 0.448,0.448 10 false A 1.958,0.635 2.406,1.083 0.448,0.448 10 false B 1.51,0.635 1.958,1.083 0.448,0.448 10 false C 1.198,0.635 1.646,1.083 0.448,0.448 10 false D 0.75,0.635 1.198,1.083 0.448,0.448 10 false E 0.438,0.635 0.885,1.083 0.448,0.448 10 false F
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Green


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F4-2 (VHP+) - Body ground Power switch on (IG) Below 1 V
F4-1 (VHP-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (VHP+) - F4-1 (VHP-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (VHP+) - Body ground Always 1 MΩ or higher
F4-1 (VHP-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (VHP+) - F4-1 (VHP-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.




OK

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE