Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1870/66  Short in Driver Side Front Seat Cushion Squib Circuit  B1871/66  Open in Driver Side Front Seat Cushion Squib Circuit  B1872/66  Short to GND in Driver Side Front Seat Cushion Squib Circuit  B1873/66  Short to B+ in Driver Side Front Seat Cushion Squib Circuit  


DESCRIPTION

The driver side front seat cushion squib circuit consists of the airbag sensor assembly and front seat airbag sub-assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side front seat cushion squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1870/66
·

The airbag sensor assembly detects a line short in the driver side front seat cushion squib circuit during the primary check.

·

Driver side front seat cushion squib malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag sub-assembly LH (Driver side front seat cushion squib)

·

Airbag sensor assembly


B1871/66
·

The airbag sensor assembly detects an open in the driver side front seat cushion squib circuit.

·

Driver side front seat cushion squib malfunction

·

Airbag sensor assembly malfunction


B1872/66
·

The airbag sensor assembly detects a short to ground in the driver side front seat cushion squib circuit.

·

Driver side front seat cushion squib malfunction

·

Airbag sensor assembly malfunction


B1873/66
·

The airbag sensor assembly detects a short to B+ in the driver side front seat cushion squib circuit.

·

Driver side front seat cushion squib malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

B471051E28
4.625,3.021 5.333,3.313 0.708,0.292 10 false M57 4.625,3.208 6.271,3.5 1.646,0.292 10 false Airbag Sensor Assembly 4.448,1.063 5.156,1.354 0.708,0.292 10 false 12 4.448,1.896 5.156,2.188 0.708,0.292 10 false 11 4.698,1.177 5.406,1.469 0.708,0.292 10 false FCD+ 4.698,2.021 5.406,2.313 0.708,0.292 10 false FCD- 2.406,1.063 3.115,1.354 0.708,0.292 10 false 2 2.406,1.896 3.115,2.188 0.708,0.292 10 false 1 1.948,1.063 2.656,1.354 0.708,0.292 10 false FCD+ 1.979,1.896 2.688,2.188 0.708,0.292 10 false FCD- 0.708,2.51 1.417,2.802 0.708,0.292 10 false M55 0.708,2.677 3.135,3.167 2.427,0.49 10 false Front Seat Airbag Sub-assembly LH (Driver Side Front Seat Cushion Squib)

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C238350C01
0.521,1.021 0.521,1.635 false 1.385,0.896 1.385,0.469 1.385,0.469 1.615,0.469 false 0.646,0.875 0.865,1.167 0.219,0.292 10 D 1.052,0.875 1.417,1.281 0.365,0.406 10 C 1.625,0.875 1.938,1.26 0.313,0.385 10 B 2.021,0.875 2.281,1.26 0.26,0.385 10 A 2.469,1.188 2.771,1.625 0.302,0.438 10 *2 0.448,1.656 0.896,1.99 0.448,0.333 10 *1 1.646,0.385 1.969,0.677 0.323,0.292 10 *3
*1 Front Seat Airbag Sub-assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat airbag sub-assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat airbag sub-assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.




OK

2.CHECK FRONT SEAT AIRBAG SUB-ASSEMBLY LH (DRIVER SIDE FRONT SEAT CUSHION SQUIB)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT AIRBAG SUB-ASSEMBLY LH (DRIVER SIDE FRONT SEAT CUSHION SQUIB)
a.
B483697C02
0.646,1.844 1.021,2.094 0.375,0.25 2.125,2.344 2.375,2.344 false 0.792,0.906 0.792,0.49 false 0.729,0.927 1.198,1.396 0.469,0.469 10 false *1 2.49,0.635 2.938,1 0.448,0.365 10 false *2 0.479,1.542 0.927,2.104 0.448,0.563 10 false *a 0.708,1.885 1.156,2.448 0.448,0.563 10 false M55 2.427,2.26 2.875,2.823 0.448,0.563 10 false SST 2.115,0.344 2.563,0.708 0.448,0.365 10 false A 1.948,0.344 2.396,0.708 0.448,0.365 10 false B 1.271,0.344 1.719,0.708 0.448,0.365 10 false C 0.906,0.344 1.354,0.708 0.448,0.365 10 false D
*1 Front Seat Airbag Sub-assembly LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Sub-assembly LH)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag sub-assembly LH (driver side front seat cushion squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1870/66, B1871/66, B1872/66 or B1873/66 is not output.


HINT:

Codes other than DTCs B1870/66, B1871/66, B1872/66 and B1873/66 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
B483698C02
1.031,2.104 1.385,2.333 0.354,0.229 1.417,0.927 1.417,0.51 false 0.594,0.958 0.594,0.542 false 1.5,2.823 1.76,2.406 false 2.313,2.823 2.052,2.406 false 0.531,0.979 1.031,1.448 0.5,0.469 10 false *1 2.385,0.677 2.813,1.104 0.427,0.427 10 false *2 1.344,0.948 1.792,1.406 0.448,0.458 10 false *3 0.74,1.719 1.177,2.25 0.438,0.531 10 false *a 1.083,2.135 1.521,2.667 0.438,0.531 10 false M55 1.344,2.823 1.802,3.188 0.458,0.365 10 false FCD- 2.198,2.823 2.656,3.188 0.458,0.365 10 false FCD+ 1.979,0.385 2.406,0.813 0.427,0.427 10 false A 1.667,0.385 2.094,0.813 0.427,0.427 10 false B 1.052,0.385 1.479,0.813 0.427,0.427 10 false C 0.74,0.385 1.167,0.813 0.427,0.427 10 false D
*1 Front Seat Airbag Sub-assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Airbag Sub-assembly LH)


Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M55-2 (FCD+) - Body ground Power switch on (IG) Below 1 V
M55-1 (FCD-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M55-2 (FCD+) - M55-1 (FCD-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M55-2 (FCD+) - Body ground Always 1 MΩ or higher
M55-1 (FCD-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M55-2 (FCD+) - M55-1 (FCD-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238353C01
0.802,0.833 0.802,1.156 false 0.938,0.708 1.542,1.438 0.604,0.729 10 false D 1.083,0.708 1.49,1.177 0.406,0.469 10 false C 1.594,0.708 1.885,1.094 0.292,0.385 10 false B 1.75,0.708 2.073,1 0.323,0.292 10 false A 2.188,1.021 2.49,1.354 0.302,0.333 10 false *2 0.74,1.167 1.115,1.521 0.375,0.354 10 false *1
*1 Front Seat Airbag Sub-assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat airbag sub-assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1870/66, B1871/66, B1872/66 or B1873/66 is not output.


HINT:

Codes other than DTCs B1870/66, B1871/66, B1872/66 and B1873/66 may be output at this time, but they are not related to this check.




OK

NG