Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/73  Short in Front Pretensioner Squib RH Circuit  B1901/73  Open in Front Pretensioner Squib RH Circuit  B1902/73  Short to GND in Front Pretensioner Squib RH Circuit  B1903/73  Short to B+ in Front Pretensioner Squib RH Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the airbag sensor assembly and front seat outer belt assembly RH.

The airbag sensor assembly uses this circuit to deploy the seat belt pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1900/73
·

The airbag sensor assembly detects a line short in the front pretensioner squib RH circuit during the primary check.

·

Front pretensioner squib RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Airbag sensor assembly


B1901/73
·

The airbag sensor assembly detects an open in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag sensor assembly malfunction


B1902/73
·

The airbag sensor assembly detects a short to ground in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag sensor assembly malfunction


B1903/73
·

The airbag sensor assembly detects a short to B+ in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C323678E84
2.135,1.052 2.646,1.292 0.51,0.24 10 false R+ 2.156,1.885 2.667,2.125 0.51,0.24 10 false R- 4.688,1.99 5.198,2.229 0.51,0.24 10 false PR- 4.688,1.156 5.198,1.396 0.51,0.24 10 false PR+ 2.417,1.042 2.615,1.271 0.198,0.229 10 false 1 2.406,1.885 2.604,2.115 0.198,0.229 10 false 2 4.51,1.063 5.396,1.365 0.885,0.302 10 false 4 4.104,1.896 5.104,2.24 1,0.344 10 false 5*1, 3*2 0.708,2.5 1.219,2.74 0.51,0.24 10 false M29 0.708,2.667 2.906,3.094 2.198,0.427 10 false Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 4.667,3.021 5.781,3.302 1.115,0.281 10 false M37*1, M58*2 4.677,3.188 6.604,3.531 1.927,0.344 10 false Airbag Sensor Assembly 0.208,3.521 3.229,3.771 3.021,0.25 10 false *2: w/ Occupant Classification System 0.208,3.271 3.26,3.521 3.052,0.25 10 false *1: w/o Occupant Classification System

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C238348C01
0.531,1.198 0.531,0.688 0.531,0.688 0.708,0.688 false 1.365,1.198 1.365,0.688 1.365,0.688 1.542,0.688 false 0.656,1.188 1.052,1.438 0.396,0.25 10 D 1.031,1.188 1.354,1.427 0.323,0.24 10 C 1.604,1.188 1.938,1.552 0.333,0.365 10 B 1.99,1.188 2.333,1.542 0.344,0.354 10 A 2.438,0.896 2.75,1.208 0.313,0.313 10 *2 0.76,0.604 1.021,0.854 0.26,0.25 10 *1 1.583,0.604 1.854,0.896 0.271,0.292 10 *3
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly RH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the front seat outer belt assembly RH side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.




OK

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)
a.
B485311C01
0.583,2.083 0.958,2.333 0.375,0.25 0.792,0.896 0.792,0.313 0.792,0.313 0.625,0.313 false 1.979,2.188 2.198,2.188 false 0.49,0.229 0.938,0.521 0.448,0.292 10 false *1 2.521,0.594 2.969,0.969 0.448,0.375 10 false *2 0.49,1.625 0.979,2.052 0.49,0.427 10 false *a 2.125,0.885 2.573,1.26 0.448,0.375 10 false A 1.958,0.885 2.406,1.26 0.448,0.375 10 false B 1.281,0.885 1.729,1.26 0.448,0.375 10 false C 0.917,0.885 1.365,1.26 0.448,0.375 10 false D 0.646,2.125 1.135,2.552 0.49,0.427 10 false M29 2.229,2.104 2.719,2.531 0.49,0.427 10 false SST
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
B485310C01
0.771,2.26 1.146,2.521 0.375,0.26 0.573,0.927 0.573,0.427 0.573,0.427 0.406,0.427 false 1.5,0.958 1.5,0.458 1.5,0.458 1.333,0.458 false 1.542,2.156 1.188,1.885 false 1.708,2.156 2.094,1.875 false 0.26,0.344 0.76,0.719 0.5,0.375 10 false *1 2.604,0.625 2.969,0.885 0.365,0.26 10 false *2 1.188,0.375 1.656,0.76 0.469,0.385 10 false *3 0.365,1.75 0.75,2.073 0.385,0.323 10 false *a 2.229,0.917 2.594,1.177 0.365,0.26 10 false A 1.823,0.917 2.188,1.177 0.365,0.26 10 false B 1.094,0.917 1.458,1.177 0.365,0.26 10 false C 0.688,0.917 1.052,1.177 0.365,0.26 10 false D 0.833,2.313 1.198,2.573 0.365,0.26 10 false M29 0.979,1.802 1.344,2.063 0.365,0.26 10 false R+ 2.125,1.802 2.49,2.063 0.365,0.26 10 false R-
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M29-1 (R+) - Body ground Power switch on (IG) Below 1 V
M29-2 (R-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M29-1 (R+) - M29-2 (R-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M29-1 (R+) - Body ground Always 1 MΩ or higher
M29-2 (R-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M29-1 (R+) - M29-2 (R-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238241C01
0.844,1.292 0.844,0.844 0.844,0.844 0.552,0.844 false 0.396,0.781 0.729,1.083 0.333,0.302 10 false *1 0.979,1.302 1.156,1.531 0.177,0.229 10 false D 1.135,1.302 1.344,1.5 0.208,0.198 10 false C 1.583,1.302 1.781,1.5 0.198,0.198 10 false B 1.74,1.302 1.938,1.542 0.198,0.24 10 false A 2.146,1.021 2.438,1.26 0.292,0.24 10 false *2
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.




OK

NG