Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Pretensioner Squib LH Circuit  B1906/74  Open in Front Pretensioner Squib LH Circuit  B1907/74  Short to GND in Front Pretensioner Squib LH Circuit  B1908/74  Short to B+ in Front Pretensioner Squib LH Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the airbag sensor assembly and front seat outer belt assembly LH.

The airbag sensor assembly uses this circuit to deploy the seat belt pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1905/74
·

The airbag sensor assembly detects a line short in the front pretensioner squib LH circuit during the primary check.

·

Front pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Airbag sensor assembly


B1906/74
·

The airbag sensor assembly detects an open in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


B1907/74
·

The airbag sensor assembly detects a short to ground in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


B1908/74
·

The airbag sensor assembly detects a short to B+ in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C323678E85
2.135,1.052 2.646,1.292 0.51,0.24 10 false L+ 2.156,1.885 2.667,2.125 0.51,0.24 10 false L- 4.688,1.99 5.198,2.229 0.51,0.24 10 false PL- 4.688,1.156 5.198,1.396 0.51,0.24 10 false PL+ 2.417,1.042 2.615,1.271 0.198,0.229 10 false 1 2.406,1.885 2.604,2.115 0.198,0.229 10 false 2 4.104,1.063 4.99,1.365 0.885,0.302 10 false 2*1, 5*2 4.104,1.896 5.104,2.24 1,0.344 10 false 1*1, 6*2 0.708,2.5 1.219,2.74 0.51,0.24 10 false M28 0.708,2.667 2.896,3.094 2.188,0.427 10 false Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 4.667,3.021 5.781,3.302 1.115,0.281 10 false M36*1, M57*2 4.677,3.188 6.604,3.531 1.927,0.344 10 false Airbag Sensor Assembly 0.208,3.521 3.229,3.771 3.021,0.25 10 false *2: w/ Occupant Classification System 0.208,3.271 3.26,3.521 3.052,0.25 10 false *1: w/o Occupant Classification System

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C284699C02
0.49,1.219 0.49,1.719 false 0.49,3.51 0.49,4.01 false 1.344,1.063 1.344,0.604 1.344,0.604 1.479,0.604 false 1.344,3.365 1.344,2.906 1.344,2.906 1.479,2.906 false 0.125,0.125 0.5,0.365 0.375,0.24 10 false *A 0.135,2.438 0.51,2.677 0.375,0.24 10 false *B 0.396,1.74 0.719,1.948 0.323,0.208 10 false *1 2.427,1.063 2.74,1.26 0.313,0.198 10 false *2 1.521,0.521 1.833,0.719 0.313,0.198 10 false *3 0.406,4.031 0.719,4.229 0.313,0.198 10 false *1 2.427,3.667 2.74,3.865 0.313,0.198 10 false *2 1.521,2.823 1.833,3.021 0.313,0.198 10 false *3 2,1.063 2.156,1.26 0.156,0.198 10 false A 1.594,1.063 1.75,1.26 0.156,0.198 10 false B 1.021,1.063 1.177,1.26 0.156,0.198 10 false C 0.615,1.063 0.771,1.26 0.156,0.198 10 false D 2,3.354 2.156,3.552 0.156,0.198 10 false A 1.594,3.354 1.75,3.552 0.156,0.198 10 false B 1.021,3.354 1.177,3.552 0.156,0.198 10 false C 0.615,3.354 0.771,3.552 0.156,0.198 10 false D
*A w/o Occupant Classification System
*B w/ Occupant Classification System
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the front seat outer belt assembly LH side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.




OK

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)
a.

Connect the connector to the airbag sensor assembly.

B485312C01
0.833,1.656 1.198,1.896 0.365,0.24 4.396,1.656 4.76,1.896 0.365,0.24 1.042,0.948 1.042,0.604 false 4.625,0.708 4.625,0.365 false 2.188,1.781 2.01,1.781 false 5.76,1.781 5.583,1.781 false 0.417,0.083 0.917,0.583 0.5,0.5 10 false *A 3.99,0.083 4.406,0.417 0.417,0.333 10 false *B 0.979,0.958 1.458,1.292 0.479,0.333 10 false *1 2.417,0.469 3,0.802 0.583,0.333 10 false *2 4.427,1.354 4.927,1.771 0.5,0.417 10 false *a 4.563,0.719 5.042,1.052 0.479,0.333 10 false *1 6,0.469 6.583,0.802 0.583,0.333 10 false *2 0.813,1.354 1.344,1.771 0.531,0.417 10 false *a 2.115,0.469 2.698,0.802 0.583,0.333 10 false A 1.979,0.469 2.563,0.802 0.583,0.333 10 false B 1.427,0.469 2.01,0.802 0.583,0.333 10 false C 1.125,0.469 1.708,0.802 0.583,0.333 10 false D 5.688,0.229 6.271,0.563 0.583,0.333 10 false A 5.563,0.229 6.146,0.563 0.583,0.333 10 false B 5.01,0.229 5.594,0.563 0.583,0.333 10 false C 4.708,0.229 5.292,0.563 0.583,0.333 10 false D 0.885,1.698 1.417,2.115 0.531,0.417 10 false M28 4.448,1.698 4.979,2.115 0.531,0.417 10 false M28 2.219,1.698 2.75,2.115 0.531,0.417 10 false SST 5.792,1.698 6.323,2.115 0.531,0.417 10 false SST
*A w/o Occupant Classification System *B w/ Occupant Classification System
*1 Front Seat Outer Belt Assembly LH *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)
- -



b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.

Disconnect the floor wire from the airbag sensor assembly.

B485313C01
0.938,1.823 1.292,2.063 0.354,0.24 4.573,1.823 4.927,2.063 0.354,0.24 0.854,0.917 0.854,0.625 false 1.604,0.896 1.604,0.604 false 4.438,0.688 4.438,0.396 false 5.198,0.656 5.198,0.365 false 1.656,1.75 1.385,1.521 false 1.781,1.76 2.073,1.521 false 5.24,1.76 4.958,1.51 false 5.365,1.76 5.646,1.521 false 0.417,0.083 1.167,0.583 0.75,0.5 10 false *A 4,0.083 4.667,0.5 0.667,0.417 10 false *B 0.792,0.927 1.271,1.427 0.479,0.5 10 false *1 6.063,0.49 6.542,0.896 0.479,0.406 10 false *2 1.542,0.896 2.104,1.219 0.563,0.323 10 false *3 0.708,1.427 1.188,1.917 0.479,0.49 10 false *a 4.375,0.708 4.854,1.208 0.479,0.5 10 false *1 2.49,0.49 2.969,0.896 0.479,0.406 10 false *2 4.302,1.417 4.781,1.906 0.479,0.49 10 false *a 5.135,0.667 5.698,0.99 0.563,0.323 10 false *3 2.198,0.5 2.677,0.906 0.479,0.406 10 false A 1.865,0.5 2.344,0.906 0.479,0.406 10 false B 1.26,0.5 1.74,0.906 0.479,0.406 10 false C 0.938,0.5 1.417,0.906 0.479,0.406 10 false D 5.771,0.26 6.25,0.667 0.479,0.406 10 false A 5.448,0.26 5.927,0.667 0.479,0.406 10 false B 4.844,0.26 5.323,0.667 0.479,0.406 10 false C 4.521,0.26 5,0.667 0.479,0.406 10 false D 0.979,1.865 1.458,2.365 0.479,0.5 10 false M28 4.625,1.865 5.104,2.365 0.479,0.5 10 false M28 1.208,1.438 1.688,1.938 0.479,0.5 10 false L+ 2.115,1.438 2.594,1.938 0.479,0.5 10 false L- 4.771,1.438 5.25,1.938 0.479,0.5 10 false L+ 5.688,1.438 6.167,1.938 0.479,0.5 10 false L-
*A w/o Occupant Classification System *B w/ Occupant Classification System
*1 Front Seat Outer Belt Assembly LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)
- -



b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M28-1 (L+) - Body ground Power switch on (IG) Below 1 V
M28-2 (L-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-1 (L+) - M28-2 (L-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-1 (L+) - Body ground Always 1 MΩ or higher
M28-2 (L-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-1 (L+) - M28-2 (L-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C284702C02
0.781,1.26 0.781,1.667 false 0.781,3.302 0.781,3.708 false 0.125,0.135 0.5,0.375 0.375,0.24 10 false *A 0.115,2.281 0.49,2.521 0.375,0.24 10 false *B 0.688,1.688 1,1.885 0.313,0.198 10 false *1 0.688,3.74 1,3.938 0.313,0.198 10 false *1 2.135,1.115 2.448,1.313 0.313,0.198 10 false *2 2.146,3.458 2.458,3.656 0.313,0.198 10 false *2 1.729,1.115 1.885,1.313 0.156,0.198 10 false A 1.563,1.115 1.719,1.313 0.156,0.198 10 false B 1.063,1.115 1.219,1.313 0.156,0.198 10 false C 0.906,1.115 1.063,1.313 0.156,0.198 10 false D 1.729,3.146 1.885,3.344 0.156,0.198 10 false A 1.563,3.146 1.719,3.344 0.156,0.198 10 false B 1.063,3.146 1.219,3.344 0.156,0.198 10 false C 0.906,3.146 1.063,3.344 0.156,0.198 10 false D
*A w/o Occupant Classification System
*B w/ Occupant Classification System
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.




OK

NG