Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Air conditioning system data and the Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the intelligent tester to check for malfunctions and perform troubleshooting.




LIST OF OPERATION METHODS


a.

By operating each of the air conditioning control switches as shown in the diagram below, it is possible to enter diagnostic check mode.

U183700E02
1.552,0.323 4.323,1.281 2.771,0.958 10 false Turn the power switch on (IG) while pressing the A/C control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears. 4.563,1.188 6.688,1.75 2.125,0.563 10 false The "AUTO" and "Recirculation/Fresh" switches are not pressed at the same time. 2.229,2.74 3.635,3.083 1.406,0.344 10 false Indicator Check (continuous operation) 2.042,4.167 3.75,4.51 1.708,0.344 10 false Sensor Check (DTC check) (continuous operation) 2.031,5.604 3.74,5.948 1.708,0.344 10 false Sensor Check (DTC check) (step operation) 4.635,5.135 5.042,5.292 0.406,0.156 10 false AUTO 3.01,5.146 3.417,5.302 0.406,0.156 10 false TEMP 2.729,6.51 3.135,6.667 0.406,0.156 10 false TEMP 1.406,7.188 4.375,7.344 2.969,0.156 10 false Check mode is canceled and A/C control starts 1.438,4.26 1.844,4.417 0.406,0.156 10 false OFF 1.448,5.677 1.854,5.833 0.406,0.156 10 false OFF 0.781,7.906 2.49,8.063 1.708,0.156 10 false : Indicates switch operation 0.521,8.333 2.167,8.49 1.646,0.156 10 false OFF: Blower fan off switch 3.104,8.333 5.656,8.49 2.552,0.156 10 false TEMP: Temperature Ajustment switch 3.115,7.906 5.667,8.063 2.552,0.156 10 false AUTO: Automatic air conditioning switch



INDICATOR CHECK


a.

Turn the power switch off.


b.

Turn the power switch on (ACC) and wait at least 5 seconds.


c.

Turn the power switch on (IG) while pressing the air conditioning control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears.

E370909C01
0.323,0.146 0.635,0.344 0.313,0.198 12 false *A 3.844,0.156 4.156,0.354 0.313,0.198 12 false *B
*A for LHD *B for RHD



d.

The indicator check is automatically performed when panel diagnosis is activated. Check that the indicators light up and go off 4 times at 1 second intervals continuously.

E370910C01
0.323,0.135 0.635,0.333 0.313,0.198 12 false *A 3.677,0.135 3.99,0.333 0.313,0.198 12 false *B 2.313,1.479 2.625,1.677 0.313,0.198 10 false *a 2.542,1.896 2.854,2.094 0.313,0.198 10 false *b 2.542,2.406 2.854,2.604 0.313,0.198 10 false *c 2.896,1.583 3.208,1.781 0.313,0.198 10 false *d 3.5,1.573 3.813,1.771 0.313,0.198 10 false *d
*A for LHD *B for RHD
*a Indicator Blinking Pattern *b ON
*c OFF *d 1 sec.


HINT:
·

The sensor check automatically starts when the indicator check is completed.

·

Press the "OFF" switch to cancel check mode.





SENSOR CHECK (DTC CHECK)


a.

Start the hybrid system and warm it up.


b.

Perform the indicator check.

HINT:

After the indicator check is completed, the system enters DTC check mode automatically.



c.

Read the DTC displayed on the display.

E370911C01
5.427,0.604 5.625,0.25 5.625,0.25 5.781,0.25 false 1.677,0.615 1.875,0.26 1.875,0.26 2.031,0.26 false 0.302,0.198 0.615,0.396 0.313,0.198 12 false *A 3.802,0.198 4.115,0.396 0.313,0.198 12 false *B 2.094,0.198 2.406,0.396 0.313,0.198 10 false *a 5.844,0.188 6.156,0.385 0.313,0.198 10 false *a
*A for LHD *B for RHD
*a Diagnostic Trouble Code (DTC) - -


NOTICE:

In sensor check mode, which is automatically entered after indicator check mode, troubleshooting may be partially performed. Be sure to perform the sensor check again.


HINT:

Refer to Diagnostic Trouble Code Chart for details of the codes.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

When there are no problems, DTC 00 is output.

·

As an example, the illustration shows that DTC 12 is output.




d.

If the DTCs are difficult to read because they change automatically, turn the "TEMP" switch clockwise to display the DTCs one at a time so that they can be read easily. The DTCs change step by step each time the "TEMP" switch is turned clockwise.

E370912C01
0.281,0.146 0.594,0.344 0.313,0.198 12 false *A 3.865,0.156 4.177,0.354 0.313,0.198 12 false *B
*A for LHD *B for RHD


HINT:

Press the "OFF" switch to finish panel diagnosis.



e.

Clear DTCs

i.

During the sensor check, press the "FRONT DEF" switch and "REAR DEF" switch simultaneously.

E370913C01
0.302,0.167 0.583,0.375 0.281,0.208 12 false *A 3.813,0.188 4.094,0.396 0.281,0.208 12 false *B
*A for LHD *B for RHD