Home › Engine / Hybrid System › 1NZ-FXE EMISSION CONTROL › CANISTER(w/o Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057007 1NZ-FXE EMISSION CONTROL _0320447 CANISTER(w/o Canister Pump Module) G

1NZ-FXE EMISSION CONTROL  CANISTER(w/o Canister Pump Module)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT CANISTER (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY) (for Fuel Tank Cap Method)


b.

Check for clogs in the air filter (when not using the GTS).

i.

Start the engine.


ii.

Warm up the engine.


iii.

Allow the engine to idle for 15 minutes.


iv.

Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


v.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


vi.
A202994

Open the fuel tank cap assembly again and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sound) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This is not a malfunction.




c.

Check for clogs in the air filter (when using the GTS).

i.

Connect the GTS to the DLC3.


ii.

Start the engine.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1

v.

Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


vi.

Perform the Active Test "Activate the EVAP Purge VSV" while the engine is idling.


vii.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


viii.

Open the fuel tank cap assembly and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sound) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This is not a malfunction.




Hide 2.INSPECT CANISTER (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY) (for Vacuum Measurement Method)

a.

Visually check the canister (fuel suction tube with pump and gauge assembly) for airtightness.

i.

Visually check the canister (fuel suction tube with pump and gauge assembly) for cracks or damage, and check that there is no gasoline smell.



b.

Inspect the airflow of the canister (fuel suction tube with pump and gauge assembly).

NOTICE:

When inspecting with parts installed on the vehicle, be sure to remove the fuel tank cap assembly.


i.
A344278C01
0.688,0.135 0.917,0.135 0.917,0.135 1.177,0.792 false 1.917,1.208 2.656,1.208 true 0.458,0.063 0.729,0.292 0.271,0.229 10 true *a 2.729,1.125 2.99,1.344 0.26,0.219 10 true *b 0.167,0.781 0.5,1.042 0.333,0.26 10 false *c
*a Port (A)
*b Port (B)
*c Air


Apply compressed air to the port (A) and check that the air flows out from the port (B).

OK:

Air flows out from the port (B).



ii.
A344279C01
2.188,1.396 2.948,1.396 true 0.688,0.49 1.094,0.49 1.094,0.49 1.229,0.844 true 0.479,0.438 0.76,0.635 0.281,0.198 10 true *a 3.042,1.333 3.323,1.573 0.281,0.24 10 true *b 2.646,2.021 2.885,2.177 0.24,0.156 10 true *c
*a Port (A)
*b Port (B)
*c Air


Close the port (A) and apply compressed air to the port (B).

OK:

Air does not flow at first. By gradually increasing the pressure, air flows when the pressure in the port reaches a certain level.



iii.
A344280C02
2.198,0.302 2.583,0.302 false 0.719,1.698 1.073,1.698 1.073,1.698 1.281,2.042 true 2.177,2.563 2.417,2 2.417,2 2.531,2 true 0.49,1.625 0.74,1.844 0.25,0.219 10 false *a 2.615,1.938 2.875,2.156 0.26,0.219 10 true *b 2.656,0.229 3,0.469 0.344,0.24 10 false *c
*a Port (A)
*b Port (B)
*c Vacuum Pump


Using a vacuum pump, apply vacuum to the port (B) with the port (A) closed.

OK:

The vacuum is maintained at first. By gradually increasing the vacuum, air flows and the vacuum decreases after the vacuum reaches a certain level.




c.
A338976C01
0.385,2.771 0.594,2.771 0.594,2.771 0.854,2.135 true 1.927,0.271 2.396,0.271 false 0.594,3.052 0.802,3.052 0.802,3.052 1.167,2.188 true 0.333,1.563 0.542,1.563 0.542,1.563 0.635,2 true 1.469,2.021 1.635,1.667 1.635,1.667 1.802,1.667 true 0.094,1.49 0.344,1.75 0.25,0.26 10 true *1 0.188,2.677 0.396,2.896 0.208,0.219 10 true *a 0.396,2.979 0.625,3.219 0.229,0.24 10 true *b 2.49,0.208 2.813,0.479 0.323,0.271 10 false *c 1.865,1.594 2.188,1.865 0.323,0.271 10 false *d
*1 No. 2 Fuel Emission Tube
*a 3-way Connector
*b Hose
*c Vacuum Pump
*d Port (A)


Check for clogs in the air filter (when not using the GTS).

i.

Connect the No. 2 fuel emission tube to the canister (fuel suction tube with pump and gauge assembly) via the 3-way connector, hose and vacuum pump as shown in the illustration.


ii.

Start the engine.


iii.

Warm up the engine.


iv.

Allow the engine to idle for 15 minutes.


v.

Check the indicator needle of the vacuum pump.

OK:

The indicator needle of the vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.




d.
A338976C01
0.385,2.771 0.594,2.771 0.594,2.771 0.854,2.135 true 1.927,0.271 2.396,0.271 false 0.594,3.052 0.802,3.052 0.802,3.052 1.167,2.188 true 0.333,1.563 0.542,1.563 0.542,1.563 0.635,2 true 1.469,2.021 1.635,1.667 1.635,1.667 1.802,1.667 true 0.094,1.49 0.344,1.75 0.25,0.26 10 true *1 0.188,2.677 0.396,2.896 0.208,0.219 10 true *a 0.396,2.979 0.625,3.219 0.229,0.24 10 true *b 2.49,0.208 2.813,0.479 0.323,0.271 10 false *c 1.865,1.594 2.188,1.865 0.323,0.271 10 false *d
*1 No. 2 Fuel Emission Tube
*a 3-way Connector
*b Hose
*c Vacuum Pump
*d Port (A)


Check for clogs in the air filter (when using the GTS).

i.

Connect the No. 2 fuel emission tube to the canister (fuel suction tube with pump and gauge assembly) via the 3-way connector, hose and vacuum pump as shown in the illustration.


ii.

Connect the GTS to the DLC3.


iii.

Start the engine.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1

vi.

Perform the Active Test "Activate the EVAP Purge VSV" while the engine is idling.


vii.

Check the needle of the vacuum pump.

OK:

The needle of the vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.