Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A38-257  Generator Temperature Sensor Circuit Low  P0A39-259  Generator Temperature Sensor Circuit High  


DESCRIPTION

Refer to the description for DTC P0A37-260 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A37-260).

DTC No. INF Code DTC Detection Condition Trouble Area
P0A38 257 Short to GND in the generator temperature sensor circuit
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Hybrid vehicle transaxle assembly (Generator temperature sensor)


P0A39 259 Open or short to +B in the generator temperature sensor circuit

HINT:

After confirming that DTC P0A38-257 or P0A39-259 is output, use the intelligent tester to check "Motor Temp No2" in the hybrid vehicle control ECU Data List.


Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to GND

WIRING DIAGRAM

A407382E22
2.302,1.177 2.76,1.375 0.458,0.198 10 false 4 1.802,1.927 2.563,2.25 0.76,0.323 10 false GMTG 1.906,1.177 2.667,1.5 0.76,0.323 10 false GMT 2.302,1.927 2.76,2.125 0.458,0.198 10 false 8 0.146,2.688 0.906,3.01 0.76,0.323 10 false C24 0.167,2.844 2.385,3.604 2.219,0.76 10 false Hybrid Vehicle Transaxle Assembly (Generator Temperature Sensor) 2.552,2.667 4.563,3.521 2.01,0.854 10 false No. 1 Engine Room Relay Block Assembly Connector 2.531,2.51 3.292,2.833 0.76,0.323 10 false CA1 3.042,1.177 3.802,1.5 0.76,0.323 10 false 22 3.042,1.938 3.802,2.26 0.76,0.323 10 false 11 3.677,1.938 4.438,2.26 0.76,0.323 10 false 11 3.677,1.177 4.438,1.5 0.76,0.323 10 false 22 4.615,1.167 5.375,1.49 0.76,0.323 10 false 26 4.865,1.167 5.625,1.49 0.76,0.323 10 false GMT 4.635,1.927 5.396,2.25 0.76,0.323 10 false 27 4.875,1.917 5.635,2.24 0.76,0.323 10 false GMTG 4.865,2.667 5.625,2.99 0.76,0.323 10 false A71 4.865,2.844 6.573,3.521 1.708,0.677 10 false Hybrid Vehicle Control ECU 5.958,1.302 6.719,1.625 0.76,0.323 10 false ADC

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 5 seconds or more.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2C-247

Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C


A

2.CHECK CONNECTOR CONNECTION CONDITION (ENGINE ROOM RELAY BLOCK NO. 1 CA1 CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (ENGINE ROOM RELAY BLOCK NO. 1 CA1 CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR TEMPERATURE SENSOR CONNECTOR)
a.
A267571N03
0.25,0.063 0.625,0.323 0.375,0.26 0.292,0.104 0.615,0.323 0.323,0.219 10 false C24

Check the connection condition of the C24 generator temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.READ VALUE USING GTS (MOTOR TEMP NO2)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (MOTOR TEMP NO2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.


d.

Read the Data List.

Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)

B

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
a.
A267571N03
0.25,0.063 0.625,0.323 0.375,0.26 0.292,0.104 0.615,0.323 0.323,0.219 10 false C24

Disconnect the C24 generator temperature sensor connector.


b.
A397757C05
1.469,0.167 1.917,0.417 0.448,0.25 0.948,1.719 1.365,1.302 true 1.792,1.729 1.479,1.094 true 0.552,0.281 0.865,0.438 0.313,0.156 10 false *a 1.656,1.76 2.115,1.958 0.458,0.198 10 false GMT 0.771,1.76 1.229,1.958 0.458,0.198 10 false GMTG 1.542,0.208 2.156,0.406 0.615,0.198 10 false C24
*a Component without harness connected
(Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-4 (GMT) - C24-8 (GMTG) Power switch off 0.3436 to 1442 kΩ


HINT:

The generator temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



c.

Reconnect the C24 generator temperature sensor connector.



OK

6.INSPECT HYBRID VEHICLE CONTROL ECU

NG

6.INSPECT HYBRID VEHICLE CONTROL ECU
a.
A395365C08
0.594,0.938 1.021,1.219 0.427,0.281 0.344,2.24 0.594,1.833 false 1.021,2.271 0.635,1.833 false 0.688,0.979 1.146,1.177 0.458,0.198 10 false A71 0.125,2.26 0.74,2.458 0.615,0.198 10 false GMTG 0.896,2.281 1.51,2.479 0.615,0.198 10 false GMT 0.177,0.583 0.49,0.74 0.313,0.156 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Connect terminals 26 (GMT) and 27 (GMTG) of connector A71 of the hybrid vehicle control ECU.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.


e.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Motor Temp No2 Terminals GMT and GMTG connected.
Power switch on (IG)
215°C (419°F)



f.

Turn the power switch off.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
a.
A267571N01
0.25,0.063 0.625,0.323 0.375,0.26 0.292,0.104 0.615,0.323 0.323,0.219 10 false C24

Disconnect the C24 generator temperature sensor connector.


b.
A397757C05
1.469,0.167 1.917,0.417 0.448,0.25 0.948,1.719 1.365,1.302 true 1.792,1.729 1.479,1.094 true 0.552,0.281 0.865,0.438 0.313,0.156 10 false *a 1.656,1.76 2.115,1.958 0.458,0.198 10 false GMT 0.771,1.76 1.229,1.958 0.458,0.198 10 false GMTG 1.542,0.208 2.156,0.406 0.615,0.198 10 false C24
*a Component without harness connected
(Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-4 (GMT) - C24-8 (GMTG) Power switch off 0.3436 to 1442 kΩ


HINT:

The generator temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



c.

Reconnect the C24 generator temperature sensor connector.



OK

8.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

NG

8.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the C24 generator temperature sensor connector.


b.

Disconnect the A71 hybrid vehicle control ECU connector.


c.
A379064C03
0.542,0.917 0.917,1.167 0.375,0.25 1.333,3.583 1.75,3.833 0.417,0.25 1.927,1.042 2.406,0.854 false 1.938,1.177 2.427,1.313 false 0.375,4.281 0.594,3.844 false 0.875,4.313 0.635,3.844 false 0.094,0.094 0.521,0.385 0.427,0.292 10 false *a 0.604,0.948 1.031,1.24 0.427,0.292 10 false C24 2.458,1.24 2.969,1.51 0.51,0.271 10 false GMTG 1.406,3.615 1.833,3.906 0.427,0.292 10 false A71 0.104,2 0.531,2.292 0.427,0.292 10 false *b 2.458,0.771 2.969,1.042 0.51,0.271 10 false GMT 0.76,4.333 1.271,4.604 0.51,0.271 10 false GMT 0.188,4.313 0.698,4.583 0.51,0.271 10 false GMTG
*a Front view of wire harness connector
(to Generator Temperature Sensor)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
C24-4 (GMT) - A71-26 (GMT) Power switch off Below 1 Ω
C24-8 (GMTG) - A71-27 (GMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
C24-4 (GMT) or A71-26 (GMT) - Body ground and other terminals Power switch off 10 kΩ or higher
C24-8 (GMTG) or A71-27 (GMTG) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A71 hybrid vehicle control ECU connector.


e.

Reconnect the C24 generator temperature sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR