Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog lights.

WIRING DIAGRAM

E374727E01
0.385,0.448 1.26,1.063 0.875,0.615 10 false from Auxiliary Battery 2.021,0.615 2.792,0.813 0.771,0.198 10 false DC/DC 2.99,0.469 3.302,0.667 0.313,0.198 10 false 3F 3.031,0.26 3.188,0.458 0.156,0.198 10 false 1 4.615,1.146 5.229,1.344 0.615,0.198 10 false TAIL 5.354,1.021 5.969,1.219 0.615,0.198 10 false TAIL 6.104,0.365 6.417,0.563 0.313,0.198 10 false 14 6.375,0.479 6.99,0.677 0.615,0.198 10 false TRLY 6.104,1.865 6.417,2.063 0.313,0.198 10 false 13 6.375,1.979 6.99,2.177 0.615,0.198 10 false FFGO 5.219,2.531 6.135,2.729 0.917,0.198 10 false FOG FR 4.49,2.656 5.406,2.854 0.917,0.198 10 false FOG FR 3.01,2.167 3.167,2.365 0.156,0.198 10 false 7 2.979,2.375 3.292,2.573 0.313,0.198 10 false 3C 1.969,2.26 2.125,2.469 0.156,0.208 10 false 2 1.99,3.552 2.146,3.76 0.156,0.208 10 false 2 0.99,2.271 1.146,2.469 0.156,0.198 10 false 1 1,3.573 1.156,3.771 0.156,0.198 10 false 1 0.833,2.844 1.292,3.042 0.458,0.198 10 false A12 0.823,2.969 4.031,3.167 3.208,0.198 10 false Fog Light Assembly LH 0.833,4.115 1.292,4.313 0.458,0.198 10 false A63 0.833,4.25 4.042,4.448 3.208,0.198 10 false Fog Light Assembly RH 3.49,3.354 6.313,3.625 2.823,0.271 10 false Instrument Panel Junction Block Assembly 5.469,3.719 5.781,3.917 0.313,0.198 10 false MB 5.469,3.875 7.125,4.615 1.656,0.74 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.




OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Front Fog Light Relay Front fog lights OFF or ON Light control switch is in tail position

OK:

Front fog light relay operates. (Front fog lights come on.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (FOG LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (FOG LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the A12 fog light assembly LH connector.


b.

Disconnect the A63 fog light assembly RH connector.


c.

Disconnect the 3C instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-2 - 3C-7 Always Below 1 Ω
A63-2 - 3C-7 Always Below 1 Ω
A12-2 or 3C-7 - Body ground Always 10 kΩ or higher
A63-2 or 3C-7 - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E173042C28
1.75,0.406 2.104,0.625 0.354,0.219 4.5,0.406 4.854,0.625 0.354,0.219 3.417,2.313 3.771,2.531 0.354,0.219 3.177,3.042 2.99,3.427 false 3.302,3.042 3.5,3.427 false 0.302,0.25 0.5,0.406 0.198,0.156 10 false *a 2.813,3.448 3.313,3.719 0.5,0.271 10 false FFGO 3.365,3.448 4.031,3.656 0.667,0.208 10 false TRLY 1.823,0.427 2.25,0.677 0.427,0.25 10 false 3F 4.583,0.438 5.021,0.667 0.438,0.229 10 false 3C 3.49,2.333 4.125,2.635 0.635,0.302 10 false MB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the auxiliary battery to terminal 3F-1.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14 (TRLY) and MB-13 (FFGO).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-7 - Body ground Always 11 to 14 V




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY