Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › from 2017.06
RM2170E _52 Drivetrain _057014 DRIVE SHAFT / PROPELLER SHAFT _0277996 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41336E 1.INSTALL FRONT DRIVE SHAFT DUST COVER

a.
C157559E07
0.698,0.719 0.542,0.281 0.542,0.281 0.385,0.281 false 0.219,0.208 0.688,0.521 0.469,0.313 10 false *1

Using a steel plate and a press, install a new front drive shaft dust cover into the front drive inboard joint assembly until it is flush with the end.

Text in Illustration
*1 Steel Plate

NOTICE:
·

Install the front drive shaft dust cover in the correct direction.

·

Do not deform the front drive shaft dust cover.




Hide 2.INSTALL OUTBOARD JOINT BOOT

a.
C166359E06
2.265,0.508 2.438,0.683 0.174,0.176 10 *1 1.883,0.843 2.125,0.601 2.125,0.601 2.263,0.601 false

Wrap the splines of the front axle outboard joint shaft assembly with protective tape to prevent the boot from being damaged.

Text in Illustration
*1 Protective Tape


b.
U154675E02
1.656,1.479 1.656,1.823 false 2.365,1.833 2.365,1.438 false 2.99,1.823 2.99,1.219 false 1.094,1.833 1.094,1.417 false 2.292,1.844 2.448,2.021 0.156,0.177 10 false *3 2.927,1.833 3.083,2.01 0.156,0.177 10 false *4 1.583,1.844 1.74,2.021 0.156,0.177 10 false *2 1.021,1.854 1.177,2.031 0.156,0.177 10 false *1

Install new parts onto the front axle outboard joint shaft assembly in the following order:

Text in Illustration
*1 Front Axle Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side

i.

Front No. 2 axle outboard joint boot clamp


ii.

Outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front axle outboard joint shaft assembly and outboard joint boot with grease.

Standard grease capacity:

116 to 126 g (4.09 to 4.44 oz.)



d.

Install the outboard joint boot onto the front axle outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 3.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C415871C01
2.156,1.5 2.677,1.5 false 0.833,1.24 1.354,1.24 false 1.917,2.031 2.438,2.031 false 2.708,1.438 3.021,1.594 0.313,0.156 10 false *a 0.667,1.177 0.979,1.333 0.313,0.156 10 false *b 1.729,1.948 2.042,2.104 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Install the front No. 2 axle outboard joint boot clamp to the outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




b.

As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415872C01
3.604,1.052 3.135,1.406 3.135,1.406 3.708,1.042 true 2.083,1.49 1.594,1.49 true 1.958,2.281 1.688,2.281 1.688,2.281 1.448,1.906 true 5.927,2.229 5.646,1.938 5.646,1.938 5.49,1.938 true 3.823,0.292 4.135,0.448 0.313,0.156 10 false *a 4.104,1.302 4.417,1.458 0.313,0.156 10 false *b 5.24,0.583 5.552,0.74 0.313,0.156 10 false *c 2.979,1.354 3.292,1.51 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.417 1.74,1.573 0.313,0.156 10 false *d 2.01,2.219 2.323,2.375 0.313,0.156 10 false *e 5.281,1.875 5.594,2.031 0.313,0.156 10 false *d
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.




c.
C233614

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

Do not damage the outboard joint boot.



Hide 43447E 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C107948

Install the front axle outboard joint boot clamp onto the outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




b.
C158356E08
2.476,0.872 2.664,1.052 0.188,0.180 10 *a

Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it.

Text in Illustration
*a Place the tip near the center of the lever.


c.
C327546

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

Do not damage the outboard joint boot.



Hide 43474A 5.INSTALL DRIVE SHAFT DAMPER SETTING CLAMP

a.
C315773E02
0.188,1.313 0.188,1.688 false 1.25,1.302 1.25,1.677 false 0.656,1.385 0.656,1.667 false 1.406,0.448 1.688,0.646 0.281,0.198 10 false (A) 0.573,1.688 0.854,1.885 0.281,0.198 10 false *2 1.167,1.698 1.448,1.896 0.281,0.198 10 false *1 0.104,1.698 0.385,1.896 0.281,0.198 10 false *1

Temporarily install the drive shaft damper and 2 new drive shaft damper setting clamps to the front axle outboard joint shaft assembly as shown in the illustration.

Text in Illustration
*1 Drive Shaft Damper Setting Clamp
*2 Drive Shaft Damper

Dimension (A):

461.6 to 465.6 mm (1.515 to 1.527 ft.)



Hide 43474 6.INSTALL DRIVE SHAFT DAMPER

a.

Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C205160E01
2.444,1.248 2.676,1.421 0.232,0.173 10 *a 2.663,0.648 2.529,1.238 2.529,1.238 1.843,0.853 false

Using needle-nose pliers, install the 2 drive shaft damper setting clamps as shown in the illustration.

Text in Illustration
*a Claws


Hide 43040 7.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
U113913E04
0.688,1.75 0.688,1.323 false 1.521,1.729 1.521,1.479 false 2.49,1.75 2.49,1.667 false 2.917,1.74 2.917,1.25 false 2.833,1.76 3.031,1.948 0.198,0.188 10 false *4 2.406,1.76 2.604,1.948 0.198,0.188 10 false *3 1.438,1.75 1.635,1.938 0.198,0.188 10 false *2 0.615,1.76 0.813,1.948 0.198,0.188 10 false *1

Install new parts onto the front axle outboard joint shaft assembly in the following order:

Text in Illustration
*1 Front Axle Inboard Joint Boot Clamp
*2 Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*4 Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side

i.

Front axle inboard joint boot clamp


ii.

Inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C157561E03
1.531,1.615 2.479,1.75 2.479,1.75 2.083,1.323 true 2.521,1.677 2.708,1.844 0.188,0.167 10 false *a

Align the matchmarks and install the tripod joint onto the front axle outboard joint shaft assembly as shown in the illustration.

Text in Illustration
*a Matchmark

NOTICE:

Face the serrated side of the tripod joint outward and install it onto the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front axle outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.




f.
C160822

Using a snap ring expander, install a new shaft snap ring to the front axle outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and inboard joint boot with grease.

Standard grease capacity:

125 to 135 g (4.40 to 4.76 oz.)



h.
C160821E06
0.918,0.354 1.095,0.531 0.177,0.177 10 *a 1.462,1.225 1.136,0.473 1.136,0.473 1.821,0.786 false

Align the matchmarks and install the front drive inboard joint assembly onto the front axle outboard joint shaft assembly.

Text in Illustration
*a Matchmark


Hide 8.INSTALL INBOARD JOINT BOOT

a.

Install the inboard joint boot to the front drive inboard joint assembly.

NOTICE:

Keep the grooves free of grease.



Hide 43448F 9.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Install the front axle inboard joint boot clamp onto the inboard joint boot.


b.

for One Touch Type:

i.
C081795

Using a screwdriver, install the front axle inboard joint boot clamp.

NOTICE:
·

Be sure to install the front axle inboard joint boot clamp in the correct position.

·

Be careful not to damage the inboard joint boot.





c.

for Claw Engagement Type:

i.
C157519E02
0.404,1.078 0.691,1.191 0.691,1.191 1.081,0.934 false 0.597,1.206 0.765,1.359 0.168,0.153 10 *a

Using needle nose pliers, install the front axle inboard joint boot clamp.

Text in Illustration
*a Claws

NOTICE:
·

Be careful not to deform the front axle inboard joint boot clamp.

·

Be careful not to damage the inboard joint boot.





Hide 43448G 10.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Install the boot clamp onto the inboard joint boot.


b.
C157783E15
1.5,1.688 1.771,1.875 0.271,0.188 10 false (A)

Adjust dimension (A) until it is within the specified length.

Dimension (A)
LH Side RH Side
562.1 mm (1.84 ft.) 842.1 mm (2.76 ft.)


c.

for One Touch Type:

i.
C081794

Using a screwdriver, install the front No. 2 axle inboard joint boot clamp.

NOTICE:
·

Be sure to install the front No. 2 axle inboard joint boot clamp in the correct position.

·

Be careful not to damage the inboard joint boot.





d.

for Claw Engagement Type:

i.
C157518E03
0.807,1.147 1.000,1.310 0.192,0.162 10 *a 0.51,0.718 0.885,1.13 0.885,1.13 1.397,0.664 false

Using needle nose pliers, install the front No. 2 axle inboard joint boot clamp.

Text in Illustration
*a Claws

NOTICE:
·

Be careful not to deform the front No. 2 axle inboard joint boot clamp.

·

Be careful not to damage the inboard joint boot.