Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2017.06
RM2170E _58 Vehicle Interior _057044 INTERIOR PANELS / TRIM _0278146 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


PROCEDURE

Hide 82171 1.INSTALL NO. 1 ROOF WIRE (w/o Coat Hook)

a.

w/o Room Light:

i.

Align the positioning tape (Red) on the front part of the No. 1 roof wire with the front tab of the roof headlining.

B485144C02
1.333,2.167 1.75,2.167 false 1.781,2.073 2.094,2.271 0.313,0.198 10 false *a
*a Marking - -
V100144

Positioning Tape (Red)
V100145

Positioning Tape
V100155

Adhesive Tape - -



ii.

Align the No. 1 roof wire positioning tape with the markings on the roof headlining.


iii.

Install the No. 1 roof wire to the roof headlining with the adhesive tape.

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.





b.

w/ Room Light:

i.

Align the positioning tape (Red) on the front part of the No. 1 roof wire with the front tab of the roof headlining.

B485145C02
1.135,2.125 1.385,2.125 false 1.406,2.042 1.719,2.24 0.313,0.198 10 false *a
*a Marking - -
V100144

Positioning Tape (Red)
V100145

Positioning Tape
V100155

Adhesive Tape - -



ii.

Align the No. 1 roof wire positioning tape with the markings on the roof headlining.


iii.

Install the No. 1 roof wire to the roof headlining with the adhesive tape.

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.





Hide 82171 2.INSTALL NO. 1 ROOF WIRE (w/ Coat Hook)

a.

Align the positioning tape (Red) on the front part of the No. 1 roof wire with the front tab of the roof headlining.

B485144C03
1.333,2.167 1.583,2.167 false 1.615,2.073 1.927,2.271 0.313,0.198 10 false *a
*a Marking - -
V100144

Positioning Tape (Red)
V100145

Positioning Tape
V100155

Adhesive Tape - -



b.

Align the No. 1 roof wire positioning tape with the markings on the roof headlining.


c.

Install the No. 1 roof wire to the roof headlining with the adhesive tape.

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 63359 3.INSTALL ROOF HEADLINING END PAD

a.

Remove the release paper from 2 new roof headlining end pads.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.
B301172E02
0.168,1.631 0.325,1.780 0.157,0.149 10 *a 0.341,1.716 0.725,1.639 false

Align the 2 roof headlining end pads with the markings on the roof headlining and install the pads as shown in the illustration.

Text in Illustration
*a Marking


Hide 63387 4.INSTALL ROOF HEADLINING FORMING PAD

a.

Remove the release paper from 2 new roof headlining forming pads.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.
B387585E01
0.208,0.923 0.366,1.072 0.157,0.149 10 *a 0.207,1.172 0.322,1.274 false 0.789,1.736 1.091,2.025 1.091,2.025 0.373,1.748 false 0.033,1.072 0.190,1.220 0.157,0.149 10 *a 1.104,1.938 1.262,2.087 0.157,0.149 10 *a 0.382,1.02 0.754,1.259 false

Align the 2 roof headlining forming pads with the markings on the roof headlining and install the pads as shown in the illustration.

Text in Illustration
*a Marking


Hide 66425B 5.INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Coat Hook)

a.
B308238E04
2.344,0.927 2.656,1.271 false 1.719,1 1.948,1.344 false 1.083,1.344 1.302,1.688 false 0.406,1.052 0.771,1.104 false 0.219,0.969 0.406,1.135 0.188,0.167 10 true *b 1.948,1.385 2.167,1.552 0.219,0.167 10 true *a 2.625,1.292 2.833,1.458 0.208,0.167 10 false *a 1.26,1.708 1.458,1.885 0.198,0.177 10 true *a

Align a new rear No. 2 side rail spacer LH with the markings on the roof headlining and install the spacer using hot-melt glue as shown in the illustration.

Text in Illustration
*a Hot-melt Glue
*b Marking


Hide 66425B 6.INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/ Coat Hook)

a.
B482707C01
0.885,1.292 0.396,1.188 0.396,1.188 0.885,0.875 true 1.948,0.802 1.865,1.531 1.865,1.531 1.531,0.802 true 1.76,1.552 1.969,1.719 0.208,0.167 10 true *a 0.177,1.104 0.396,1.292 0.219,0.188 10 true *b
*a Hot-melt Glue
*b Marking


Align a new rear No. 2 side rail spacer LH with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.


Hide 66414A 7.INSTALL REAR NO. 2 SIDE RAIL SPACER RH

HINT:

Use the same procedure as for the LH side.


Hide 63343 8.INSTALL NO. 3 ROOF SILENCER PAD (w/o Coat Hook)

a.

Align a new No. 3 roof silencer pad with the markings on the roof headlining and install the pad using hot-melt glue as shown in the illustration.

B392185E02
6.802,0.396 6.927,0.635 false 4.917,1.396 5.281,1.552 false 3.438,1.75 3.802,1.917 false 6.865,0.635 7.021,0.781 0.156,0.146 10 false *b 6.156,0.281 6.271,0.427 0.115,0.146 10 false A 6.625,0.719 6.74,0.865 0.115,0.146 10 false A 5.292,1.5 5.448,1.646 0.156,0.146 10 true *b 3.281,1.688 3.438,1.833 0.156,0.146 10 true *a

Text in Illustration
*a Hot-melt Glue *b Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 63343 9.INSTALL NO. 3 ROOF SILENCER PAD (w/ Coat Hook)

a.

Align a new No. 3 roof silencer pad with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

B483111C02
6.479,0.417 6.583,0.583 false 3.625,2.615 3.625,2.948 3.625,2.948 3.958,2.615 true 4.906,2.646 4.833,2.917 4.833,2.917 5.365,2.646 true 5.406,1.75 5.74,1.667 5.74,1.667 5.313,1.333 true 4.479,1.24 4.333,0.927 true 3.667,1.25 3.417,0.833 3.417,0.833 4,1.25 true 3.917,1.833 3.333,1.583 3.333,1.583 3.917,1.417 true 3.927,0.833 4.427,1.417 true 5.052,1.385 4.802,0.719 true 3.917,2.417 3.313,2.344 3.313,2.344 4.479,1.885 true 5.25,2.417 5.667,2.417 5.667,2.417 5.146,1.885 true 4.083,2.75 4.5,2.417 true 3.104,1.49 3.302,1.667 0.198,0.177 10 true *a 6.521,0.594 6.833,0.75 0.313,0.156 10 false *b 5.833,0.302 5.99,0.5 0.156,0.198 10 false A 6.302,0.719 6.458,0.917 0.156,0.198 10 false A 3.542,2.938 3.833,3.083 0.292,0.146 10 true *b 4.75,2.917 5.042,3.063 0.292,0.146 10 true *b 5.75,1.583 6.042,1.729 0.292,0.146 10 true *b 4.219,0.75 4.51,0.896 0.292,0.146 10 false *b 3.271,0.667 3.563,0.813 0.292,0.146 10 false *b 3.115,2.25 3.313,2.427 0.198,0.177 10 true *a 3.792,0.656 3.99,0.833 0.198,0.177 10 false *a 4.667,0.552 4.865,0.729 0.198,0.177 10 false *a 5.698,2.333 5.896,2.51 0.198,0.177 10 true *a 3.99,2.729 4.188,2.906 0.198,0.177 10 true *a
*a Hot-melt Glue *b Marking


Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 63342 10.INSTALL NO. 2 ROOF SILENCER PAD (w/o Coat Hook)

a.

w/o Room Light:

i.

Align a new No. 2 roof silencer pad and with the markings on the roof headlining and install the pad using hot-melt glue as shown in the illustration.

B443909C02
2.188,1.5 2.542,1.469 false 3.688,1.917 4.271,2.031 false 1.24,0.469 1.333,0.635 false 0.604,0.344 0.948,0.635 0.344,0.292 10 false A 1.281,0.667 1.625,0.958 0.344,0.292 10 false *b 4.292,1.969 4.5,2.167 0.208,0.198 10 true *a 2,1.427 2.198,1.615 0.198,0.188 10 true *b 1.042,0.771 1.385,1.063 0.344,0.292 10 false A

Text in Illustration
*a Hot-melt Glue *b Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)




b.

w/ Room Light:

i.

Align a new No. 2 roof silencer pad with the markings on the roof headlining and install the pad using hot-melt glue as shown in the illustration.

B392181C01
0.466,0.674 0.582,0.823 0.116,0.149 10 A 0.868,0.272 0.983,0.421 0.116,0.149 10 A 0.83,0.581 0.987,0.730 0.157,0.149 10 *b 4.722,2.132 4.879,2.281 0.157,0.149 10 *a 2.29,1.345 2.447,1.494 0.157,0.149 10 *b 0.395,0.363 0.83,0.643 false 2.435,1.41 2.83,1.571 false 3.958,1.893 4.718,2.202 false

Text in Illustration
*a Hot-melt Glue *b Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)




Hide 63342 11.INSTALL NO. 2 ROOF SILENCER PAD (w/ Coat Hook)

a.

Align a new No. 2 roof silencer pad with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

B483112C03
0.24,0.688 0.323,0.5 false 2.948,1.292 2.865,0.875 true 3.458,1.26 3.76,0.844 3.76,0.844 3.677,1.26 true 3.323,2.615 3.573,2.948 3.573,2.948 3.583,2.635 true 2.76,2.906 2.76,2.656 true 2,2.667 1.938,2.844 1.938,2.844 2.25,2.635 true 2.198,2.438 1.948,1.854 1.948,1.854 2.281,1.917 true 2.802,2.448 4,2.167 4,2.167 3.385,2.448 true 3.458,1.896 3.833,1.917 true 2.917,1.917 3.917,1.75 true 3,1.479 4.417,1.583 4.417,1.583 3.5,1.448 true 2.427,1.458 2.333,0.917 true 1.854,1.5 2.188,1.5 true 2.573,1.271 2.573,0.938 true 4.031,2.063 4.281,2.229 0.25,0.167 10 true *a 0.177,0.688 0.49,0.844 0.313,0.156 10 false *b 0.417,0.76 0.573,0.958 0.156,0.198 10 false A 0.854,0.333 1.01,0.531 0.156,0.198 10 false A 2.49,0.75 2.802,0.906 0.313,0.156 10 false *b 2.75,0.698 3.063,0.854 0.313,0.156 10 false *b 3.656,0.667 3.969,0.823 0.313,0.156 10 false *b 1.854,2.833 2.094,2.99 0.24,0.156 10 true *b 2.688,2.906 2.927,3.063 0.24,0.156 10 true *b 3.531,2.958 3.771,3.115 0.24,0.156 10 true *b 1.688,1.698 1.917,1.875 0.229,0.177 10 true *a 3.948,1.635 4.198,1.802 0.25,0.167 10 true *a 3.865,1.833 4.115,2 0.25,0.167 10 true *a 4.427,1.479 4.677,1.646 0.25,0.167 10 true *a 2.229,0.74 2.458,0.917 0.229,0.177 10 false *a 1.667,1.396 1.917,1.583 0.25,0.188 10 true *b
*a Hot-melt Glue *b Marking


Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 63341 12.INSTALL NO. 1 ROOF SILENCER PAD

a.
B392179E01
0.482,0.216 0.639,0.365 0.157,0.149 10 *a 1.199,0.761 1.315,0.910 0.116,0.149 10 A 1.716,0.266 1.832,0.415 0.116,0.149 10 A 0.664,0.299 1.105,0.392 false

Align a new No. 1 roof silencer pad with the markings on the roof headlining and install the pad using hot-melt glue as shown in the illustration.

Text in Illustration
*a Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 63341D 13.INSTALL FRONT ROOF SILENCER PAD

a.
B392177E01
2.772,0.216 2.929,0.365 0.157,0.149 10 *a 1.525,0.264 1.641,0.413 0.116,0.149 10 A 2.045,0.796 2.161,0.945 0.116,0.149 10 A 2.259,0.437 2.766,0.301 false

Align 2 new roof headlining silencer pads with the markings on the roof headlining and install the pads using hot-melt glue as shown in the illustration.

Text in Illustration
*a Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 73137A 14.INSTALL UPPER SHOULDER BELT ANCHOR COVER

a.
B297740

Install the seat belt anchor cover to the roof headlining.


b.

Engage the 4 claws to install the upper shoulder belt anchor cover.


Hide 63355D 15.INSTALL ROOF HEADLINING PAD LH (w/ Coat Hook)

a.
B300811E02
3.031,2.344 2.677,2.385 false 0.969,2.948 0.875,2.729 false 0.885,2.948 1.042,3.094 0.156,0.146 10 false *b 2.5,2.313 2.656,2.458 0.156,0.146 10 false *a

Align the a new roof headlining pad LH with markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

Text in Illustration
*a Hot-melt Glue
*b Marking


Hide 63355C 16.INSTALL ROOF HEADLINING PAD RH (w/ Coat Hook)

HINT:

Use the same procedure as for the LH side.


Hide 63148 17.INSTALL ROOF PANEL PAD (w/ Coat Hook)

a.
B300809E02
1.792,2.667 1.698,2.427 false 2.25,2.594 2.021,2.531 false 2.26,2.51 2.417,2.656 0.156,0.146 10 false *b 1.698,2.677 1.854,2.823 0.156,0.146 10 false *a

Align the a new roof panel pad with markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

Text in Illustration
*a Hot-melt Glue
*b Marking


Hide 63119E 18.INSTALL NO. 1 ROOF PANEL PAD (w/ Coat Hook)

HINT:

Use the same procedure as for the roof panel pad.


Hide 66426B 19.INSTALL REAR NO. 3 SIDE RAIL SPACER LH (w/ Coat Hook)

a.

Align a new rear No. 3 side rail spacer LH with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

B483114C01
3.438,0.938 3.833,0.833 3.833,0.833 3.448,0.729 false 4.719,0.948 5.135,0.781 5.135,0.781 4.719,0.615 false 6.396,0.927 6.083,0.75 6.083,0.75 6.396,0.51 false 4,1.25 3.635,1.104 false 4.833,1.25 5.083,1.104 false 3.167,0.552 3.417,0.417 false 4,0.417 4.25,0.542 false 6.583,1.271 6.604,1.115 false 5.167,0.667 5.479,0.823 0.313,0.156 10 false *a 4.042,1.167 4.354,1.323 0.313,0.156 10 false *b 3.844,0.729 4.156,0.885 0.313,0.156 10 false *a 3.438,0.292 3.75,0.448 0.313,0.156 10 false *b 5.885,0.635 6.198,0.792 0.313,0.156 10 false *a 3.823,0.271 4.135,0.427 0.313,0.156 10 false *b 6.458,1.25 6.771,1.406 0.313,0.156 10 false *b 4.646,1.167 4.958,1.323 0.313,0.156 10 false *b
*a Hot-melt Glue *b Marking



Hide 66416 20.INSTALL REAR NO. 3 SIDE RAIL SPACER RH (w/ Coat Hook)

HINT:

Use the same procedure as for the LH side.


Hide 62436 21.INSTALL FRONT ROOF SIDE RAIL PAD LH (w/ Coat Hook)

a.
B441675E02
2.99,1.156 2.896,0.854 false 2.917,1.156 3.073,1.302 0.156,0.146 10 false *a

Align a new front roof side rail pad LH with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

Text in Illustration
*a Marking


Hide 62435B 22.INSTALL FRONT ROOF SIDE RAIL PAD RH (w/ Coat Hook)

HINT:

Use the same procedure as for the LH side.


Hide 63352D 23.INSTALL NO. 2 ROOF HEADLINING PAD (w/ Coat Hook)

a.
B300805E02
1.531,1.719 1.281,1.74 false 2.417,1.854 2.052,1.813 false 2.427,1.771 2.583,1.917 0.156,0.146 10 false *b 1.094,1.656 1.25,1.802 0.156,0.146 10 false *a

Align a new No. 2 roof headlining pad with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

Text in Illustration
*a Hot-melt Glue
*b Marking


Hide 63351C 24.INSTALL ROOF HEADLINING PAD (w/ Coat Hook)

HINT:

Use the same procedure as for No. 2 roof headlining pad.


Hide 63341G 25.INSTALL ROOF SILENCER PAD (w/ Coat Hook)

a.

Remove the release paper from a new roof silencer pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.
B441673E03
2.625,0.927 2.75,0.719 false 2.51,0.948 2.74,1.208 0.229,0.26 10 false *a

Align the roof silencer pad with the markings on the roof headlining and install it as shown in the illustration.

Text in Illustration
*a Marking

HINT:

Use the same procedure for the RH side and LH side.



Hide 86101J 26.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 86730C 27.INSTALL AMPLIFIER MICROPHONE ASSEMBLY

Hide 63359B 28.INSTALL ROOF HEADLINING RETAINER COVER