Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2017.06
RM2170E _51 Engine / Hybrid System _057012 CRUISE CONTROL _0277986 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the hybrid vehicle control ECU. When the hybrid vehicle control ECU receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. Cruise control cancellation occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the hybrid vehicle control ECU through the STOP fuse and the stop light switch assembly, and the hybrid vehicle control ECU turns the cruise control off.

DTC No. DTC Detection Condition Trouble Area
P0571 Voltage of STP signal and that of ST1- signal of hybrid vehicle control ECU are less than 1 V for 0.5 seconds or more
·

Stop light switch assembly

·

Stop light switch circuit

·

Hybrid vehicle control ECU



WIRING DIAGRAM

B381571E29
0.5,0.479 1.344,0.917 0.844,0.438 10 false from Auxiliary Battery 0.75,1 1.906,1.198 1.156,0.198 10 false IG2 relay 2.833,1.875 4.76,2.063 1.927,0.188 10 false Stop Light Switch Assembly 5.198,1.719 6.979,2.125 1.781,0.406 10 false Hybrid Vehicle Control ECU 1.844,0.667 2.76,0.865 0.917,0.198 10 false DC/DC 2.552,0.677 3.469,0.875 0.917,0.198 10 false STOP 2.052,1.146 3.188,1.385 1.135,0.24 10 false IG2 NO. 2 3.25,0.521 3.573,0.75 0.323,0.229 10 false B 3.24,1 3.563,1.229 0.323,0.229 10 false B 3.24,1.354 3.563,1.583 0.323,0.229 10 false GND 3.833,1.188 4.156,1.417 0.323,0.229 10 false L 3.833,0.615 4.156,0.844 0.323,0.229 10 false L 3.083,0.417 3.406,0.646 0.323,0.229 10 false 1 3.083,0.906 3.406,1.135 0.323,0.229 10 false 5 3.083,1.26 3.406,1.49 0.323,0.229 10 false 3 4.021,0.521 4.344,0.75 0.323,0.229 10 false 2 4.031,1.094 4.354,1.323 0.323,0.229 10 false 4 5.406,0.615 5.729,0.844 0.323,0.229 10 false A71 5.406,1.177 5.729,1.406 0.323,0.229 10 false A72 5.448,0.438 5.771,0.667 0.323,0.229 10 false 15 5.448,1 5.771,1.229 0.323,0.229 10 false 28 2.844,1.719 3.167,1.948 0.323,0.229 10 false A65 5.75,0.625 6.073,0.854 0.323,0.229 10 false STP 5.75,1.188 6.167,1.385 0.417,0.198 10 false ST1-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WIRE HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE)
a.
U183740E02
1.708,1.281 1.76,1.698 false 1.354,1.292 1.177,1.698 false 2.094,1.271 2.271,1.688 false 0.104,0.063 0.396,0.302 0.292,0.24 10 false *a 1.573,0.26 2.146,0.469 0.573,0.208 10 false A65 1.073,1.708 1.219,1.885 0.146,0.177 10 false B 1.615,1.719 1.938,1.896 0.323,0.177 10 false GND 2.25,1.708 2.573,1.885 0.323,0.177 10 false B

Disconnect the A65 stop light switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-1 (B)- A65-3 (GND) Power switch off 11 to 14 V
A65-5 (B)- A65-3 (GND) Power switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A65-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A71 and A72 hybrid vehicle control ECU connectors.


b.

Disconnect the A65 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A71-15 (STP) - A65-2 (L) Always Below 1 Ω
A72-28 (ST1-) - A65-4 (L) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A71-15 (STP) or A65-2 (L) - Body ground Always 10 kΩ or higher
A72-28 (ST1-) or A65-4 (L) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)