In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using the CAN communication system. The combination meter assembly displays an engine coolant temperature warnings based on the data received from the ECM.
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI system.
w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DIAGNOSTIC TROUBLE CODE CHART
w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DIAGNOSTIC TROUBLE CODE CHART
If the exhaust heat recirculation system has a malfunction, the water temperature warning is displayed to inform the driver of the malfunction.
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output | A |
| CAN communication DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR
w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| SFI system DTCs are output | B |
A
B
w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DIAGNOSTIC TROUBLE CODE CHART
w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus:
for Combination Meter: Body / Combination Meter / Data List.
for Engine: Powertrain / Engine and ECT / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temperature | Engine coolant temperature / 0 to 127.5°C (0 to 261.5°F) | After warming up: 75 to 100°C (167 to 212°F) | - |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Coolant Temp | Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up | ·
Stored as Freeze Frame Data ·
This is the engine coolant temperature. |
|
|||
Enter inspection mode.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Result | Proceed to |
|---|---|
| The data list values of the ECUs do not match | A |
| The data list values of the ECUs match | B |
When the Data List values of the ECUs do not match, a signal output error of the ECM is suspected.
A
B
Replace the combination meter assembly with a new or a known good one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
The operation of the water temperature warning light returns to normal.
OK
NG