19100P
1. PERFORM SPARK TEST
Check for DTCs.
w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR
w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR
If any DTC is output, perform troubleshooting procedures for that DTC.
Remove the ignition coil assemblies and spark plugs.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL
Disconnect the 4 injector connectors.
Set the vehicle to inspection mode. (Step 3)
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Install the spark plug into the ignition coil assembly, and then connect the ignition coil connector. (Step 4)
Ground the spark plug. (Step 5)
Check that spark occurs at each spark plug while the engine is being cranked. (Step 6)
Be sure to ground the spark plugs when checking them.
Do not crank the engine for more than 2 seconds.
Cranking will stop if the power switch is pushed again for models with cranking holding function.
If a spark plug has been struck or dropped, replace it.
If an ignition coil assembly has been struck or dropped, replace it.
Repeat steps 3 to 6 for each spark plug and ignition coil assembly.
If spark does not occur for any cylinder, perform the following Inspect Ignition Coil and Spark Test procedure.
Connect the 4 fuel injector connectors.
Install the spark plugs and ignition coil assemblies.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION
Check for DTCs.
w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR
w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR
Clear the DTCs.
w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR
w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR
19500
2.INSPECT IGNITION COIL AND SPARK TEST
Perform "Inspection After Repair" after replacing the spark plug and ignition coil assembly.
w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION
Check that the wire harness side connector of the ignition coil assembly is securely connected.
| Result | Action |
|---|---|
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on each ignition coil assembly.
Replace the ignition coil assembly with a known good one.
Set the vehicle to inspection mode.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Perform the spark test again.
| Result | Action |
|---|---|
| NG | Go to next step |
| OK | Replace ignition coil assembly |
Perform a spark test on each spark plug.
Replace the spark plug with a known good one.
Set the vehicle to inspection mode.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
19100P
3.CHECK SPARK PLUG
Do not use a wire brush for cleaning.
Do not adjust the electrode gap of a used spark plug.
Perform "Inspection After Repair" after replacing the spark plug.
w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION
Check the electrode using a megohmmeter:
| *a | Ground |
Using a megohmmeter, measure the insulation resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Spark plug (terminal part) - Body ground | Always | 10 MΩ or higher |
If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:
Quickly accelerate the engine to 2500 rpm 5 times.
Remove the spark plug.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its thread and insulator.
If there is any damage, replace the spark plug.
| Manufacturer | Spark Plug Type |
|---|---|
| DENSO | FK16R-A8 (except Hong Kong and Taiwan) |
| FK16BR-AL8 (for Hong Kong and Taiwan) |
Reference:
Check the spark plug electrode gap.
1.1 mm (0.0433 in.)
If the gap is more than the maximum, replace the spark plug.
Never attempt to adjust the gap of a used plug.
0.7 to 0.8 mm (0.0276 to 0.0315 in.)
| *A | FK16R-A8 (except Hong Kong and Taiwan) |
| *B | FK16BR-AL8 (for Hong Kong and Taiwan) |
| *a | Spark plug electrode gap |
| *b | Iridium Tip |
| *c | Platinum Tip |
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
588 kPa (6.0 kgf/cm2, 85 psi)
20 seconds or less
Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
Install the spark plug.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION