Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Drive Start Control System  


DESCRIPTION

The drive start control is controlled by the hybrid vehicle control ECU.

If the hybrid vehicle control ECU determines that the shift lever and accelerator pedal are operated abnormally, driving torque is restricted and, when necessary, a warning is displayed on the combination meter assembly.

C312753E12
0.344,0.25 2.656,0.469 2.313,0.219 10 false Accelerator Pedal Sensor Assembly 0.365,1.052 2.063,1.531 1.698,0.479 10 false Steering Angle Sensor and Yaw Rate Sensor 0.406,2.417 2.365,3.125 1.958,0.708 10 false Shift Lever Position Sensor 0.396,3.406 1.979,3.813 1.583,0.406 10 false Vehicle Speed Sensor or Wheel Speed Sensor 2.917,3.771 4.031,4.125 1.115,0.354 10 false Vehicle Speed 2.729,2.604 4.094,2.875 1.365,0.271 10 false Shift Lever Position 2.677,1.458 3.99,1.885 1.313,0.427 10 false Vehicle Acceleration and Steering Angle 2.76,0.479 3.938,0.854 1.177,0.375 10 false Actual accelerator opening 5.427,1.063 7.052,1.656 1.625,0.594 10 false Meter Display Request 5.5,3.094 7.021,3.333 1.521,0.24 10 false Driving Torque Request 3.708,4.198 5.604,4.448 1.896,0.25 10 false Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

HINT:

Even if the accelerator pedal position is maintained, the engine output may increase when driving uphill and decrease when driving downhill. This is due to the drive start control controlling the driving torque, and is not a malfunction.


PROCEDURE

1.SYMPTOM CONFIRMATION
a.

Interview the customer to confirm the problem.

Result:
Result Proceed to
Hunting A
Hesitation/poor acceleration B




A

2.PAST ACTIVATION CONFIRMATION

B

8.PAST ACTIVATION CONFIRMATION
2.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:

Drive Start Control Activation Conditions


i.

Condition 1 (Reverse control)

Activation conditions
·

The shift lever is in R.

·

The accelerator pedal is depressed.


A322483E07
1.156,0.156 2.396,0.427 1.24,0.271 10 false Shift Lever Position 1.24,0.521 2.365,0.781 1.125,0.26 10 false Accelerator Pedal 2.667,0.177 2.823,0.375 0.156,0.198 10 false R 3.115,0.521 3.427,0.719 0.313,0.198 10 false ON 2.927,0.99 3.615,1.292 0.688,0.302 10 false Activated 4.625,1.563 5.365,1.823 0.74,0.26 10 false Restricted 1.573,1.573 2.458,1.896 0.885,0.323 10 false Driving Torque 3.698,2.427 4.094,2.646 0.396,0.219 10 false Time

Items Controlled
·

Driving torque is restricted.


Deactivation Conditions
·

The shift lever is moved to any position other than R.

·

The accelerator pedal is released.



ii.

Condition 2 (Shift control A)

Activation conditions
·

The shift lever is moved from P to any forward position (D or B) or R.

·

The accelerator pedal is open by approximately 1/5 or more.


A322484E06
1.063,0.177 2.292,0.406 1.229,0.229 10 false Shift Lever Position 1.135,0.51 2.24,0.729 1.104,0.219 10 false Accelerator Pedal 2.594,0.188 2.771,0.438 0.177,0.25 10 false P 3.156,0.188 3.333,0.438 0.177,0.25 10 false D 2.531,0.542 2.802,0.75 0.271,0.208 10 false ON 2.917,0.865 3.563,1.104 0.646,0.24 10 false Activated 1.49,1.615 2.406,1.885 0.917,0.271 10 false Driving Torque 4.479,1.563 5.208,1.792 0.729,0.229 10 false Restricted 3.656,2.438 4.271,2.635 0.615,0.198 10 false Time

Items Controlled
·

Driving torque is restricted.


Deactivation Conditions
·

The shift lever is in P or N.

·

The accelerator pedal is released.



iii.

Condition 3 (Shift control B)

Activation conditions
·

The shift lever is moved from R to any forward position (D or B), any forward position (D or B) to R, or N to R.

·

The accelerator pedal is open by approximately 1/5 or more.


A322485E07
1.083,0.167 2.302,0.417 1.219,0.25 10 false Shift Lever Position 1.156,0.531 2.302,0.771 1.146,0.24 10 false Accelerator Pedal 2.594,0.177 2.75,0.375 0.156,0.198 10 false N 3.156,0.188 3.313,0.385 0.156,0.198 10 false R 2.531,0.542 2.833,0.771 0.302,0.229 10 false ON 2.917,0.833 3.521,1.063 0.604,0.229 10 false Activated 1.49,1.625 2.375,1.885 0.885,0.26 10 false Driving Torque 3.615,2.427 4.229,2.625 0.615,0.198 10 false Time 4.573,1.542 5.375,1.813 0.802,0.271 10 false Restricted

Items Controlled
·

Driving torque is restricted.


Deactivation Conditions
·

The shift lever is in P or N.

·

The accelerator pedal is released.


HINT:

During reverse control or shift control, driving torque is adjusted based on the road gradient and steering angle.




Result:
Result Proceed to
Performed A
Not performed B



A

3.CHECK DTC OUTPUT

B

3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / Utility / All Codes.


d.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output. A
DTCs are output B



e.

Turn the power switch off.



A

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

B

GO TO DTC CHART

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.


d.

Read the value displayed on the intelligent tester.

Tester Display Measurement Item / Range Normal Condition
FR Wheel Speed Front speed sensor RH
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
When driving at constant speed:
No large fluctuations
FL Wheel Speed Front speed sensor LH
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
When driving at constant speed:
No large fluctuations
RR Wheel Speed Rear speed sensor RH
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
When driving at constant speed:
No large fluctuations
RL Wheel Speed Rear speed sensor LH
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
When driving at constant speed:
No large fluctuations

Standard:
Tester Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle being driven at constant speed between 16 to 64 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



e.

Turn the power switch off.



OK

5.READ VALUE USING GTS (VEHICLE SPD)

NG

5.READ VALUE USING GTS (VEHICLE SPD)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Spd.


d.

Read the value displayed on the intelligent tester.

Standard:
Tester Display Condition Specified Condition
Vehicle Spd Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at a constant speed (16 to 64 km/h (10 to 40 mph)) No large fluctuations in displayed speed


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



e.

Turn the power switch off.



OK

6.READ VALUE USING GTS (DECELERATION SENSOR)

NG

INSPECT ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

6.READ VALUE USING GTS (DECELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Deceleration Sensor and Deceleration Sensor2.


d.

Read the value displayed on the intelligent tester.

Standard:
Tester Display Condition Specified Condition
Deceleration Sensor
Deceleration Sensor2
During deceleration Value changes with vehicle speed
During acceleration Value changes with vehicle speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



e.

Turn the power switch off.



OK

7.READ VALUE USING GTS (STEERING ANGLE SENSOR)

NG

7.READ VALUE USING GTS (STEERING ANGLE SENSOR)
a.

Connect the GTSto the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Steering Angle Sensor.


d.

Read the value displayed on the intelligent tester.

Tester Display Measurement Item / Range Normal Condition
Steering Angle Sensor Steering angle sensor
Min.: -3276.8 degrees, Max.: 3276.7 degrees
Turning left: Increases
Turning right: Decreases

Standard:
Tester Display Condition Specified Condition
Steering Angle Sensor Steering wheel turned left Value increases with steering wheel operation
Steering wheel turned right Value decreases with steering wheel operation


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



e.

Turn the power switch off.



OK

NG

8.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:

Drive Start Control Activation Conditions


i.

Condition 1 (Reverse control)

Activation conditions
·

The shift lever is in R.

·

The accelerator pedal is depressed.


A322483E07
1.156,0.156 2.396,0.427 1.24,0.271 10 false Shift Lever Position 1.24,0.521 2.365,0.781 1.125,0.26 10 false Accelerator Pedal 2.667,0.177 2.823,0.375 0.156,0.198 10 false R 3.115,0.521 3.427,0.719 0.313,0.198 10 false ON 2.927,0.99 3.615,1.292 0.688,0.302 10 false Activated 4.625,1.563 5.365,1.823 0.74,0.26 10 false Restricted 1.573,1.573 2.458,1.896 0.885,0.323 10 false Driving Torque 3.698,2.427 4.094,2.646 0.396,0.219 10 false Time

Items Controlled
·

Driving torque is restricted.


Deactivation Conditions
·

The shift lever is moved to any position other than R.

·

The accelerator pedal is released.



ii.

Condition 2 (Shift control A)

Activation conditions
·

The shift lever is moved from P to any forward position (D or B) or R.

·

The accelerator pedal is open by approximately 1/5 or more.


A322484E06
1.063,0.177 2.292,0.406 1.229,0.229 10 false Shift Lever Position 1.135,0.51 2.24,0.729 1.104,0.219 10 false Accelerator Pedal 2.594,0.188 2.771,0.438 0.177,0.25 10 false P 3.156,0.188 3.333,0.438 0.177,0.25 10 false D 2.531,0.542 2.802,0.75 0.271,0.208 10 false ON 2.917,0.865 3.563,1.104 0.646,0.24 10 false Activated 1.49,1.615 2.406,1.885 0.917,0.271 10 false Driving Torque 4.479,1.563 5.208,1.792 0.729,0.229 10 false Restricted 3.656,2.438 4.271,2.635 0.615,0.198 10 false Time

Items Controlled
·

Driving torque is restricted.


Deactivation Conditions
·

The shift lever is in P or N.

·

The accelerator pedal is released.



iii.

Condition 3 (Shift control B)

Activation conditions
·

The shift lever is moved from R to any forward position (D or B), any forward position (D or B) to R, or N to R.

·

The accelerator pedal is open by approximately 1/5 or more.


A322485E07
1.083,0.167 2.302,0.417 1.219,0.25 10 false Shift Lever Position 1.156,0.531 2.302,0.771 1.146,0.24 10 false Accelerator Pedal 2.594,0.177 2.75,0.375 0.156,0.198 10 false N 3.156,0.188 3.313,0.385 0.156,0.198 10 false R 2.531,0.542 2.833,0.771 0.302,0.229 10 false ON 2.917,0.833 3.521,1.063 0.604,0.229 10 false Activated 1.49,1.625 2.375,1.885 0.885,0.26 10 false Driving Torque 3.615,2.427 4.229,2.625 0.615,0.198 10 false Time 4.573,1.542 5.375,1.813 0.802,0.271 10 false Restricted

Items Controlled
·

Driving torque is restricted.


Deactivation Conditions
·

The shift lever is in P or N.

·

The accelerator pedal is released.


HINT:

During reverse control or shift control, driving torque is adjusted based on the road gradient and steering angle.




Result:
Result Proceed to
Not performed A
Performed B


HINT:

If the customer operated the vehicle in a way which caused the drive start control to operate, explain the operation of the system to the customer and that the operation is not a malfunction.



A

9.CHECK DTC OUTPUT

B

SYSTEM NORMAL

9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / Utility / All Codes.


d.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output. A
DTCs are output B



e.

Turn the power switch off.



A

10.INSPECT SHIFT LEVER POSITION SENSOR

B

GO TO DTC CHART

10.INSPECT SHIFT LEVER POSITION SENSOR

A

11.READ VALUE USING GTS (ACCEL PEDAL POS #1, ACCEL PEDAL POS #2)

B