Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2170E _55 Steering _057026 POWER ASSIST SYSTEMS _0278045 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1512/12  Torque Sensor2  


DESCRIPTION

The power steering ECU assembly supplies a voltage of 5 V to the torque sensor (electric power steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (electric power steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

While DTC C1512/12 is detected, power assist is stopped due to fail-safe operation.

DTC No. DTC Detection Condition Trouble Area
C1512/12 Diagnosis Condition: IG ON
Malfunction Status: TRQ2 voltage is less than 0.25 V or more than 4.6 V
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly



WIRING DIAGRAM

C375646E20
5.844,0.594 6.156,0.792 0.313,0.198 10 false 5V 5.094,0.802 5.708,1 0.615,0.198 10 false TRQV 5.135,1.594 5.75,1.792 0.615,0.198 10 false TRQ2 5.115,2.271 5.729,2.469 0.615,0.198 10 false TRQG 4.875,0.802 5.063,1.031 0.188,0.229 10 false 8 4.885,1.479 5.042,1.677 0.156,0.198 10 false 1 4.885,2.229 5.042,2.427 0.156,0.198 10 false 2 4.792,2.938 5.104,3.135 0.313,0.198 10 false z7 4.813,3.094 7.115,3.375 2.302,0.281 10 false Power Steering ECU Assembly 0.427,3.01 2.865,3.385 2.438,0.375 10 false Torque Sensor (Electric Power Steering Column Sub-assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

If the electric power steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



PROCEDURE

1.CHECK POWER STEERING ECU ASSEMBLY (TRQ2 VOLTAGE)
a.
C375640C19
0.365,0.969 0.76,1.229 0.396,0.26 1.781,0.896 2.24,0.406 true 1.083,0.521 1.469,0.875 true 1.677,1.49 1.271,1.885 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 0.875,1.833 1.49,2.031 0.615,0.198 10 false TRQV 0.688,0.49 1.302,0.688 0.615,0.198 10 false TRQ2 2.313,0.354 2.927,0.552 0.615,0.198 10 false TRQG 0.51,1.031 0.823,1.229 0.313,0.198 10 false z7
*a Component without harness connected
(Torque Sensor (Electric Power Steering Column Sub-assembly))


Disconnect the power steering ECU assembly connector.


b.

Connect 3 new 1.5 V batteries in series to prepare a 4.5 V power supply.

HINT:

Check that the voltage of the prepared power supply is 4.5 V.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z7-1(TRQ2) - z7-2(TRQG)
1.

Connect the 4.5 V positive (+) terminal to z7-8 (TRQV) and 4.5 V negative (-) terminal to z7-2 (TRQG)

2.

Steering wheel not being turned (without load)


2.07 to 2.43 V
1.

Connect the 4.5 V positive (+) terminal to z7-8 (TRQV) and 4.5 V negative (-) terminal to z7-2 (TRQG)

2.

Steering wheel being turned to right with vehicle stopped


1.08 to 2.25 V
1.

Connect the 4.5 V positive (+) terminal to z7-8 (TRQV) and 4.5 V negative (-) terminal to z7-2 (TRQG)

2.

Steering wheel being turned to left with vehicle stopped


2.25 to 3.42 V


NOTICE:

To avoid damaging the torque sensor (electric power steering column assembly), do not apply a voltage of more than 5 V.


HINT:
·

The voltage values specified above are applicable when using an applied voltage of 4.5 V, and vary depending on the applied voltage (When compared to values for an applied voltage of 5 V, these values differ by a factor of 0.9).

·

When using an applied voltage of 5 V, the specified values are as follows.

Condition Specified Condition
Steering wheel not being turned (without load) 2.3 to 2.7 V
Steering wheel being turned to right with vehicle stopped 1.2 to 2.5 V
Steering wheel being turned to left with vehicle stopped 2.5 to 3.8 V




Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY