Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2018.08
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0461  Fuel Level Sensor "A" Circuit Range / Performance  


DESCRIPTION

The fuel sender gauge is located inside the fuel tank and measures the amount of fuel. The fuel sender gauge converts the fuel level in the fuel tank into a resistance value and outputs it to the combination meter assembly. The ECM determines when it is necessary to refuel the vehicle based on changes in the output value of the fuel sender gauge.

DTC No. DTC Detection Condition Trouble Area
P0461 The change in the fuel sender gauge value is below the threshold when a certain amount of fuel is calculated to have been consumed. (1 trip detection logic).
·

Fuel sender gauge assembly

·

ECM



MONITOR DESCRIPTION

When the fuel sender gauge assembly output value changes less than a specified amount, when compared to the fuel consumption calculated from the fuel injection volume, the ECM will detect a malfunction, illuminate the MIL and store a DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel level sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A421650E05
1.083,1.917 2,2.115 0.917,0.198 10 false Idling 0.104,2.229 1.698,2.479 1.594,0.25 10 false Power Switch on (IG) 0.333,1.094 1.375,1.656 1.042,0.563 10 false 80 km/h or more [Engine running] 0.469,0.385 1.479,0.917 1.01,0.531 10 false Vehicle Speed 6.781,2.604 7.146,2.854 0.365,0.25 10 false Time 1.927,2.083 2.844,2.281 0.917,0.198 10 false [A] 2.344,1.813 3.26,2.01 0.917,0.198 10 false [B] 3.385,0.698 4.302,0.896 0.917,0.198 10 false [C] 3.146,0.417 4.063,0.615 0.917,0.198 10 false 30 minutes 5.333,0.427 6.25,0.625 0.917,0.198 10 false 30 minutes 4.458,3.135 5.375,3.333 0.917,0.198 10 false [D] 5.594,0.719 6.51,0.917 0.917,0.198 10 false [E] 6.604,3.125 6.938,3.458 0.333,0.333 10 false [F]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

8.

Start the engine [B].

9.

Drive the vehicle at 80 km/h (50 mph) or more for 30 minutes [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0461

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [F] again.



15.

Drive the vehicle at 80 km/h (50 mph) or more for 30 minutes [E].

16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

19.

Input the DTC: P0461

20.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INTERVIEW THE CUSTOMER
a.

Interview the customer for details about when the they refuel the vehicle.

HINT:

When the fuel tank is full, if the vehicle is repeatedly driven a short distance and then refueled, the fuel sender gauge output value will not change. In this case, the ECM may judge that the fuel sender gauge is stuck and store DTC P0461. If the vehicle was driven in this manner, as the DTC was stored due to a user action, clear the DTCs without performing troubleshooting and return the vehicle to the customer.



Result:
Proceed to
NEXT



NEXT

2.INSPECT FUEL SENDER GAGE ASSEMBLY