Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2018.08
RM2170E _55 Steering _057026 POWER ASSIST SYSTEMS _0278045 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in a speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the power switch from off (lock) to on (ready).

WIRING DIAGRAM

C406427E02
1.75,0.938 1.969,1.094 0.219,0.156 10 false G4 0.938,1.813 1.188,1.979 0.25,0.167 10 false CG 0.958,0.927 1.208,1.094 0.25,0.167 10 false TS 1.344,0.719 1.542,0.875 0.198,0.156 10 false 12 1.385,1.594 1.583,1.75 0.198,0.156 10 false 4 5.667,2.927 5.885,3.073 0.219,0.146 10 false G6 6.031,0.927 6.229,1.073 0.198,0.146 10 false TS 5.833,0.813 6.01,0.958 0.177,0.146 10 false 6 5.917,2.927 6.896,3.271 0.979,0.344 10 false Power Steering ECU Assembly 0.573,2.927 0.958,3.083 0.385,0.156 10 false DLC3 1.76,0.719 1.958,0.875 0.198,0.156 10 false 12 1.802,1.594 2,1.75 0.198,0.156 10 false 4 1.75,1.813 1.969,1.969 0.219,0.156 10 false G4 1.292,0.938 1.75,1.135 0.458,0.198 10 false G93 1.281,1.823 1.74,2.021 0.458,0.198 10 false G93 1.323,1.177 1.635,1.375 0.313,0.198 10 false *1 1.333,2.052 1.646,2.25 0.313,0.198 10 false *1 1.75,1.167 2.063,1.365 0.313,0.198 10 false *2 1.75,2.052 2.063,2.25 0.313,0.198 10 false *2 1.333,3.25 3.021,3.448 1.688,0.198 10 false *1: for LHD 2.75,3.25 4.438,3.448 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - TS of DLC3)
a.

Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G6-6 (TS) - G93-12 (TS) Always Below 1 Ω
G6-6 (TS) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G6-6 (TS) - G4-12 (TS) Always Below 1 Ω
G6-6 (TS) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C406212C17
1.51,0.844 1.885,1.083 0.375,0.24 1.51,1.208 1.885,1.448 0.375,0.24 1.646,1.927 2.479,1.229 false 0.313,0.281 0.625,0.479 0.313,0.198 10 false *a 1.604,1.25 1.917,1.448 0.313,0.198 10 false G4 1.563,0.885 1.875,1.083 0.313,0.198 10 false G93 1.948,0.885 2.26,1.083 0.313,0.198 10 false *1 1.958,1.24 2.271,1.438 0.313,0.198 10 false *2 2.479,1.052 2.792,1.25 0.313,0.198 10 false CG
*a Front view of DLC3
*1 for LHD
*2 for RHD


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G93-4 (CG) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
G4-4 (CG) - Body ground Always Below 1 Ω




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR