Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2019.07
RM2170E _58 Vehicle Interior _057037 METER / GAUGE / DISPLAY _0278095 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. DTC Detection Condition Trouble Area
B1507 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Open in turn signal light circuit


·

Harness or connector

·

Bulb

·

Instrument panel junction block assembly

·

Combination meter assembly


B1508 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Short in turn signal light circuit or hazard warning light circuit


·

Harness or connector

·

Bulb

·

Instrument panel junction block assembly

·

Combination meter assembly



WIRING DIAGRAM

E418897E01
6.073,0.938 6.385,1.135 0.313,0.198 10 false LL 6.073,4.958 6.385,5.156 0.313,0.198 10 false LR 5.802,0.813 6.115,1.01 0.313,0.198 10 false 13 5.875,4.823 6.188,5.021 0.313,0.198 10 false 7 4.76,0.74 5.073,0.938 0.313,0.198 10 false 24 4.771,4.76 5.083,4.958 0.313,0.198 10 false 25 4.76,4.958 5.073,5.156 0.313,0.198 10 false 3B 4.76,0.969 5.073,1.167 0.313,0.198 10 false 3B 3.083,6.99 3.396,7.188 0.313,0.198 10 false 3B 3.073,2.927 3.385,3.125 0.313,0.198 10 false 3B 3.083,0.948 3.396,1.146 0.313,0.198 10 false 3C 3.083,1.938 3.396,2.135 0.313,0.198 10 false 3D 3.094,5.979 3.406,6.177 0.313,0.198 10 false 3D 3.094,0.75 3.406,0.948 0.313,0.198 10 false 28 3.094,1.74 3.406,1.938 0.313,0.198 10 false 18 3.094,2.729 3.406,2.927 0.313,0.198 10 false 38 3.135,5.781 3.448,5.979 0.313,0.198 10 false 5 3.094,4.958 3.406,5.156 0.313,0.198 10 false 3C 3.104,4.771 3.417,4.969 0.313,0.198 10 false 38 3.094,6.802 3.406,7 0.313,0.198 10 false 39 2.271,0.833 2.583,1.031 0.313,0.198 10 false 1 2.292,1.823 2.604,2.021 0.313,0.198 10 false 5 2.281,3.823 2.594,4.021 0.313,0.198 10 false 2 2.292,4.833 2.604,5.031 0.313,0.198 10 false 1 2.281,2.823 2.594,3.021 0.313,0.198 10 false 2 2.292,5.865 2.604,6.063 0.313,0.198 10 false 5 2.292,6.885 2.604,7.083 0.313,0.198 10 false 2 2.292,7.896 2.604,8.094 0.313,0.198 10 false 2 0.948,0.823 1.26,1.021 0.313,0.198 10 false 2 0.927,1.802 1.24,2 0.313,0.198 10 false 1 0.927,2.823 1.24,3.021 0.313,0.198 10 false 9 0.927,3.823 1.24,4.021 0.313,0.198 10 false 9 0.927,4.823 1.24,5.021 0.313,0.198 10 false 2 0.927,5.854 1.24,6.052 0.313,0.198 10 false 1 0.938,6.875 1.25,7.073 0.313,0.198 10 false 9 0.938,7.896 1.25,8.094 0.313,0.198 10 false 9 1.125,1.813 1.281,2.01 0.156,0.198 10 false E 2.083,1.823 2.24,2.021 0.156,0.198 10 false B 2.104,2.823 2.26,3.021 0.156,0.198 10 false B 1.156,2.823 1.313,3.021 0.156,0.198 10 false - 2.104,3.823 2.26,4.021 0.156,0.198 10 false B 1.156,3.813 1.313,4.01 0.156,0.198 10 false - 2.094,5.865 2.25,6.063 0.156,0.198 10 false B 1.135,5.865 1.292,6.063 0.156,0.198 10 false E 1.146,6.865 1.302,7.063 0.156,0.198 10 false - 2.094,6.885 2.25,7.083 0.156,0.198 10 false B 2.125,7.896 2.281,8.094 0.156,0.198 10 false B 1.135,7.896 1.292,8.094 0.156,0.198 10 false - 5.281,5.677 5.594,5.875 0.313,0.198 10 false G3 5.281,5.833 7.156,6.083 1.875,0.25 10 false Combination Meter Assembly 2.583,2.823 2.896,3.021 0.313,0.198 10 false *1 2.594,3.813 2.906,4.01 0.313,0.198 10 false *2 0.74,1.188 1.198,1.385 0.458,0.198 10 false A93 0.74,1.333 2.563,1.563 1.823,0.229 10 false Headlight Assembly LH 0.521,2.156 0.979,2.354 0.458,0.198 10 false M5 0.521,2.313 2.885,2.563 2.365,0.25 10 false Rear Combination Light Assembly LH 0.563,3.146 1.021,3.344 0.458,0.198 10 false J7 0.583,4.146 1.042,4.344 0.458,0.198 10 false J7 0.74,5.198 1.198,5.396 0.458,0.198 10 false A92 0.76,5.365 3.125,5.615 2.365,0.25 10 false Headlight Assembly RH 0.51,6.198 0.969,6.396 0.458,0.198 10 false M6 0.521,6.365 2.885,6.615 2.365,0.25 10 false Rear Combination Light Assembly RH 2.604,6.875 2.917,7.073 0.313,0.198 10 false *1 2.604,7.906 2.917,8.104 0.313,0.198 10 false *2 0.531,3.302 2.896,3.552 2.365,0.25 10 false Outer Rear View Mirror Assembly LH 0.51,7.385 2.875,7.635 2.365,0.25 10 false Outer Rear View Mirror Assembly RH 0.521,7.24 0.979,7.438 0.458,0.198 10 false H7 0.583,8.24 1.042,8.438 0.458,0.198 10 false H7 0.313,9.479 2.875,9.75 2.563,0.271 10 false *1: for Bulb Type Side Turn Signal Light 3.219,8.531 4.823,9.146 1.604,0.615 10 false Instrument Panel Junction Block Assembly 2.958,9.479 5.521,9.75 2.563,0.271 10 false *2: for LED Type Side Turn Signal Light 0.573,4.323 2.906,4.656 2.333,0.333 10 false Outer Rear View Mirror Assembly LH 0.563,8.396 2.896,8.729 2.333,0.333 10 false Outer Rear View Mirror Assembly RH 0.135,0.083 1.958,0.313 1.823,0.229 12 false for Halogen Headlight

E418897E03
6.083,0.938 6.396,1.135 0.313,0.198 10 false LL 6.073,4.948 6.385,5.146 0.313,0.198 10 false LR 5.802,0.823 6.115,1.021 0.313,0.198 10 false 13 5.875,4.865 6.188,5.063 0.313,0.198 10 false 7 4.76,0.76 5.073,0.958 0.313,0.198 10 false 24 4.771,4.76 5.083,4.958 0.313,0.198 10 false 25 4.76,4.969 5.073,5.167 0.313,0.198 10 false 3B 4.76,0.938 5.073,1.135 0.313,0.198 10 false 3B 3.083,7.01 3.396,7.208 0.313,0.198 10 false 3B 3.073,2.938 3.385,3.135 0.313,0.198 10 false 3B 3.094,0.958 3.406,1.156 0.313,0.198 10 false 3C 3.083,1.938 3.396,2.135 0.313,0.198 10 false 3D 3.094,5.99 3.406,6.188 0.313,0.198 10 false 3D 3.094,0.771 3.406,0.969 0.313,0.198 10 false 28 3.094,1.729 3.406,1.927 0.313,0.198 10 false 18 3.094,2.74 3.406,2.938 0.313,0.198 10 false 38 3.135,5.792 3.448,5.99 0.313,0.198 10 false 5 3.094,4.969 3.406,5.167 0.313,0.198 10 false 3C 3.104,4.76 3.417,4.958 0.313,0.198 10 false 38 3.094,6.813 3.406,7.01 0.313,0.198 10 false 39 2.271,0.833 2.583,1.031 0.313,0.198 10 false 1 2.292,1.823 2.604,2.021 0.313,0.198 10 false 5 2.292,3.833 2.604,4.031 0.313,0.198 10 false 2 2.271,4.844 2.583,5.042 0.313,0.198 10 false 1 2.292,2.823 2.604,3.021 0.313,0.198 10 false 2 2.292,5.875 2.604,6.073 0.313,0.198 10 false 5 2.292,6.906 2.604,7.104 0.313,0.198 10 false 2 2.292,7.906 2.604,8.104 0.313,0.198 10 false 2 0.938,0.823 1.25,1.021 0.313,0.198 10 false 2 0.927,1.813 1.24,2.01 0.313,0.198 10 false 1 0.927,2.823 1.24,3.021 0.313,0.198 10 false 9 0.927,3.823 1.24,4.021 0.313,0.198 10 false 9 0.927,4.854 1.24,5.052 0.313,0.198 10 false 2 0.938,5.854 1.25,6.052 0.313,0.198 10 false 1 0.938,6.906 1.25,7.104 0.313,0.198 10 false 9 0.938,7.896 1.25,8.094 0.313,0.198 10 false 9 1.125,1.813 1.281,2.01 0.156,0.198 10 false E 2.083,1.823 2.24,2.021 0.156,0.198 10 false B 2.104,2.823 2.26,3.021 0.156,0.198 10 false B 1.156,2.813 1.313,3.01 0.156,0.198 10 false - 2.104,3.833 2.26,4.031 0.156,0.198 10 false B 1.177,3.823 1.333,4.021 0.156,0.198 10 false - 2.094,5.875 2.25,6.073 0.156,0.198 10 false B 1.146,5.865 1.302,6.063 0.156,0.198 10 false E 1.146,6.896 1.302,7.094 0.156,0.198 10 false - 2.094,6.906 2.25,7.104 0.156,0.198 10 false B 2.115,7.906 2.271,8.104 0.156,0.198 10 false B 1.135,7.885 1.292,8.083 0.156,0.198 10 false - 5.281,5.656 5.594,5.854 0.313,0.198 10 false G3 5.281,5.833 7.156,6.083 1.875,0.25 10 false Combination Meter Assembly 2.583,2.823 2.896,3.021 0.313,0.198 10 false *1 2.594,3.823 2.906,4.021 0.313,0.198 10 false *2 0.74,1.135 1.198,1.333 0.458,0.198 10 false A95 0.74,1.292 2.563,1.521 1.823,0.229 10 false Headlight Assembly LH 0.521,2.146 0.979,2.344 0.458,0.198 10 false M5 0.521,2.292 2.885,2.542 2.365,0.25 10 false Rear Combination Light Assembly LH 0.542,3.156 1,3.354 0.458,0.198 10 false J7 0.583,4.156 1.042,4.354 0.458,0.198 10 false J7 0.76,5.198 1.219,5.396 0.458,0.198 10 false A96 0.76,5.333 3.125,5.583 2.365,0.25 10 false Headlight Assembly RH 0.51,6.208 0.969,6.406 0.458,0.198 10 false M6 0.521,6.354 2.885,6.604 2.365,0.25 10 false Rear Combination Light Assembly RH 2.604,6.906 2.917,7.104 0.313,0.198 10 false *1 2.604,7.896 2.917,8.094 0.313,0.198 10 false *2 0.521,3.302 2.885,3.552 2.365,0.25 10 false Outer Rear View Mirror Assembly LH 0.521,7.406 2.885,7.656 2.365,0.25 10 false Outer Rear View Mirror Assembly RH 0.531,7.26 0.99,7.458 0.458,0.198 10 false H7 0.583,8.24 1.042,8.438 0.458,0.198 10 false H7 0.313,9.479 2.875,9.75 2.563,0.271 10 false *1: for Bulb Type Side Turn Signal Light 3.188,8.51 4.781,9.135 1.594,0.625 10 false Instrument Panel Junction Block Assembly 2.958,9.479 5.521,9.75 2.563,0.271 10 false *2: for LED Type Side Turn Signal Light 0.573,4.323 2.906,4.656 2.333,0.333 10 false Outer Rear View Mirror Assembly LH 0.563,8.396 2.896,8.729 2.333,0.333 10 false Outer Rear View Mirror Assembly RH 0.115,0.073 1.938,0.302 1.823,0.229 12 false for LED Headlight

CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs for this system before performing the following inspection procedure.

Side turn signal light assembly*: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


*: for LED Type Side Turn Signal Light


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.

Result:
Result Proceed to
Turn signal lights for one side do not illuminate A
Front turn signal light does not illuminate B
Rear turn signal light does not illuminate C
Side turn signal light does not illuminate D




A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT (HEADLIGHT ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

D

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G3 combination meter assembly connector.


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
G3-13 (LL) - 3B-24 Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
G3-7 (LR) - 3B-25 Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
G3-13 (LL) or 3B-24 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
G3-7 (LR) or 3B-25 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT (HEADLIGHT ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

for Halogen Headlight

i.

Disconnect the A92*1 or A93*2 front turn signal light (headlight assembly) connector.

*1: for RH

*2: for LH



ii.

Disconnect the 3C instrument panel junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A93-1 - 3C-28 Always Below 1 Ω
A93-2 - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A92-1 - 3C-38 Always Below 1 Ω
A92-2 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A93-1 or 3C-28 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A92-1 or 3C-38 - Body ground Always 10 kΩ or higher




b.

for LED Headlight

i.

Disconnect the A96*1 or A95*2 front turn signal light (headlight assembly) connector.

*1: for RH

*2: for LH



ii.

Disconnect the 3C instrument panel junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A95-1 - 3C-28 Always Below 1 Ω
A95-2 - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A96-1 - 3C-38 Always Below 1 Ω
A96-2 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A95-1 or 3C-28 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A96-1 or 3C-38 - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B





A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the M6*1 or M5*2 rear turn signal light connector.

*1: for RH

*2: for LH



b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
M5-5 (B) - 3D-18 Always Below 1 Ω
M5-1 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
M6-5 (B) - 3D-5 Always Below 1 Ω
M6-1 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
M5-5 (B) or 3D-18 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
M6-5 (B) or 3D-5 - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the H7*1 or J7*2 outer rear view mirror assembly connector.

*1: for RH

*2: for LH



b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
J7-2 (B) - 3B-38 Always Below 1 Ω
J7-9 (-) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
H7-2 (B) - 3B-39 Always Below 1 Ω
H7-9 (-) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
J7-2 (B) or 3B-38 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
H7-2 (B) or 3B-39 - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U183702E02
1.177,0.969 1.5,1.135 0.323,0.167 10 false 3B 0.052,0 0.375,0.167 0.323,0.167 10 false *a 5.802,0.948 6.125,1.115 0.323,0.167 10 false 3D 3.458,0.979 3.781,1.146 0.323,0.167 10 false 3C


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-25 - 3C-38 Always Below 1 Ω
3B-25 - 3D-5 Always Below 1 Ω
3B-25 - 3B-39 Always Below 1 Ω
3B-24 - 3C-28 Always Below 1 Ω
3B-24 - 3D-18 Always Below 1 Ω
3B-24 - 3B-38 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY